Thanks for the great video. I did this after watching your video on my 2011 Nissan Rogue (X-Trail in Europe), there were 4 bolts instead of 3 but the part was exactly the same. By any chance, do you know the torque specs of the bolts? Thanks again :)
I drive a Nissan Qashqai j 10 1. 6 petrol engine I have a problem when I go over something big I hear a dull sound what do you can this fix my problem?
Thanks for watching. Sorry I dont. I only make videos of jobs that come into the garage if one comes in for Replacement al make a video. Thanks for watching
i have a question. my nissan qashqai the poke of it , it moves a little bit on the forth acceleration , i have changed the left motor mount and it is still there, my friend checked the middel one. underneeth the motor, and it doesnt move there. and the right one doesnt move eather. what could couse the moving of the poke ?
@@TEAMR4ULTV thank you for your prompt response. It would be so nice if you can provide your workshop address as I am looking for Clutch set replacement and center mount aswell for my Nissan Quashqui n-tec Petrol 2010 reg.
I have a 2012 Nissan Qashqai, 2 liter gasoline engine. Lately the car shakes when standing, for example when I'm at a red light. If I shift from D to N or lift the handbrake the shaking stops.
Thanks just fixed my wife’s card, she has had this fault for years, made the ride very rough. Now it’s a beauty.
Thanks for watching really appreciate it
looks easy enough, going to give this a shot!
job done, thanks for the video super easy job. the old mount rubber was knackered
Good luck and good video bro.
Thanks for watching really appreciate it
Thanks, nice so you don’t need to have a jack on the engine ?
Great easy explanation 👍
A pesar el idioma, pude comprender el tutorial.
Gracias
Is the engine stabiliser also called lower gearbox mounting thanks.
Thanks for watching really appreciate it. I would say yes
Thank you very much so informative 👌
Thanks mate very helpful
Thanks for the great video. I did this after watching your video on my 2011 Nissan Rogue (X-Trail in Europe), there were 4 bolts instead of 3 but the part was exactly the same. By any chance, do you know the torque specs of the bolts? Thanks again :)
Thanks for watching really appreciate it. I'll be honest I just got a breaker bar and just tighten it up
@@TEAMR4ULTV I found the answer in the haynes manual. All 4 bolts are 81 ft/lbs. Probably the same in Qashqai.
I drive a Nissan Qashqai j 10 1. 6 petrol engine I have a problem when I go over something big I hear a dull sound what do you can this fix my problem?
Great video and nice accent 👍
Thanks guys. Great video
Thanks for watching really appreciate it
Do you need to support the gearbox when changing these ?
No you don't need to
Have to check that mount on mine. Replaced CV-axels but the shakeings got moutch worse.
Thanks for watching really appreciate it. It's easy to do don't worry about it.
Does anyone know the torque settings for these bolts
Thanks
Great video do you have the part number please.
Have you ever changed the other engine mounts on one of these, I'm aiming to change my central mount but I'm guessing more than that one have gone
I have replaced the mount on other cars not on QASHQAI but shouldn't be that hard
@@TEAMR4ULTV no worries bud, I'll do what needs doing and take a look at the others see if I can get it done
great have you got movie how to do other two mounts?
Thanks for watching.
Sorry I dont. I only make videos of jobs that come into the garage if one comes in for Replacement al make a video. Thanks for watching
my center bolt is only undoing a bit then going tight, what do you recommend. thanks
Thanks for watching really appreciate it. If you can, can you get a nut and bolt on it
Does the 2011 model have the same mount set up?..
It should do yes
@@TEAMR4ULTV cheers mate
i have a question. my nissan qashqai the poke of it , it moves a little bit on the forth acceleration , i have changed the left motor mount and it is still there, my friend checked the middel one. underneeth the motor, and it doesnt move there. and the right one doesnt move eather. what could couse the moving of the poke ?
Thanks for watching really appreciate it. Check the front Wishbone Bushes
hey mate! i have a same car and only bad vibrating when put gear on D and R . would it be centre engine mount?
thanks!
Could be try it,its very cheap to do worth a try
Nice one
What was the customer experiencing with the car before the job was done?
It was making a clunky noise when changing gears
@@TEAMR4ULTV I’m getting juddering or engine movement when idling.
@@criszafi2940 could be that I would try it
Only this mount engine for qashqai ? Is there more or only this?
You should have a mount on driver side top of engine. One on top of gear box passenger side
Thank you great video.
Is this the 1.5 dCi K9K engine?
Yes
Hi there.. can you please tell me the part code number for said engine mount
To be honest I just gave the Registration to the parts shop and they gave me the part
@@TEAMR4ULTV thank you for your prompt response. It would be so nice if you can provide your workshop address as I am looking for Clutch set replacement and center mount aswell for my Nissan Quashqui n-tec Petrol 2010 reg.
Is this mount fit to Nissan note 2014 ?
Should be the same
I suffer from vibrations during acceleration
Thanks for watching really appreciate it. The vibration could be anything from bent drive shaft, tyre has bulge in it etc so many other things.
I have a 2012 Nissan Qashqai, 2 liter gasoline engine.
Lately the car shakes when standing, for example when I'm at a red light.
If I shift from D to N or lift the handbrake the shaking stops.
@@c.s.b6459 that has to be something to do with the auto box
WTF is a qashqai?
Nissan QASHQAI I don't know what they call it in other parts of the world but in uk its call Nissa QASHQAI
It's called Rogue Sport in USA. Sub-compact version of Rogue/X-Trail