How to install Mikuni Carburetor on mini bike! +20mph

[@STLWILDONE]

1:15 INSTALL STARTS FOR ANYBODY NEEDING IT

[@dawsonrickman1500]

Always put the bracket on carb first... so u can look down the bracket to see if it lines up with the O gasket built in if not then it can cause an air leak and run like crap

[@baudeliodiaz4094]

Pulling hoses, taking nuts and bolts pretty much easy to figure out but the ONLY special part of the job you Did Not take time to explain...taking off and putting back the cable that controls the amount of gas put into the mix. The cable that is activated when you push on the gas pedal

[@Ohio_Hobbies_Guy]

What do i do with the governor? We arent removing it.

[@undagroundhustla]

Very good question.🤔

[@Cal3b587]

Just leave it in their as long as you don't upgrade the valve springs the stock ones will float before it gets too high of rpm

[@Harristunerracing]

Fun fact yall before y’all put that carburetor on there you haft to remove the ! governor ! If not it will break of in to you motor so that’s one thing he didn’t show you

[@Gera-zm4et]

So the governor will break?

[@LovejoyBoi785]

@@Gera-zm4etDEFINITELY

[@isaiahperez7010]

It’s that a stock motor

[@Deucealive75]

It won't break if RPM is limited. I wouldn't trust it 6K RPM and up. I use a small bracket bolted to the head to connect the spring to. Governor just pulls on it like it does with the stock carb. I'm running 5K RPM and under so it's not a concern.

[@b-stodomingokenluii9202]

@@Deucealive75how to know if how much rpm you running like if you doing 50mph is that low?

[@DollarhiteDelight]

Says ur gonna show how to install it then skips over the steps of unhooking of the old one, or how u assembled the new one…wtf

[@ryantevlin4884]

Hey did u have to order a new throttle cable? I ordered the same kit for my Colman ct200uxe and I haven’t installed it yet. Or can I by pass it with this carb? Also great video really helpful and well Shit my guy.

[@xptics]

so the stock cable doesn’t have a bead on the end for it to hook into the slide on the carb, you could either get a soldering iron and some solder and put that on the end or get a new cable

[@JayBubba]

That’s the part I hated most with mine 😂

[@aidenbecker6325]

Can you link everything in the description or something otherwise this video is damn near unless unless you already magically have the same filter card and manifold

[@ajvanhouten7687]

Have the same exact carburetor leaks a lot of gas miss around with it for two hours or one

[@elliottfilms6254]

I would just check all the seals

[@AJ-uf2tp]

should i have not removed my throttle assembly on the motor? will that affect it idk i havent heard it run yet

[@chrishall1025]

Have you figured that out I’m not sure if I shouldn’t have

[@Cal3b587]

​@chrishall1025 this completely bypasses the whole throttle assembly and governor

[@dangotti3454]

Put the carb up n first guys trust me if it don’t line up well it won’t be an enjoyable experience

[@shushunliu6572]

Do I have to remove the governor arm for my 212cc since I have have governor removed will the governor arm effect my engine with high idle since I have the mikuni installed just curious?

[@lilbitotoxic]

did you findout? should i remove it

[@shushunliu6572]

@@lilbitotoxicyeah it’s fine after I started mine up it did no high idle effect just ran quietly with choke on

[@TAKEoverIAN]

What parts of the linkage do you take off

[@jasongallardo7075]

What throttle cable did you use

[@Mlox]

I put it all on its getting fuel from the tank but its not spraying into the engine

[@elliottfilms6254]

I will be coming out with another video answering all the questions so ask them in the comments!!

[@dallas749]

what did you do about the govenor? does it still limit at 4000rpm

[@carsonlarabie]

Does anyone know if this setup would work on a Baja 196cc

[@125club]

Wonder the same just got one yesterday

[@Cal3b587]

​@@125clubtheir both clones of the same engine your good it'll fit

[@Nimbo-hn3ri]

What do you do with the line that sticks out of the top of the fuel tank

[@cuh_2023]

It’s just to release fumes from the gas tank just cut it short

[@Nimbo-hn3ri]

@@cuh_2023 thanks

[@mexico3484]

@@Nimbo-hn3rihow’d it go?

[@user-oj3fw3fw8r]

Would it work on a 100cc engine

[@starlaheartless2708]

Did the belts come with the carburetor

[@troyholland3436]

Do I half to remove the Throddle linkage ?

[@cuh_2023]

You don’t have to but to me it just looks way better with it off

[@gtanino2061]

Does the mikuni come tuned already?

[@dangotti3454]

You just did a governer bypass if I’m not mistaken. Upgraded your flywheel?

[@jacklivingston4182]

i’ve done the same thing but haven’t upgraded my flywheel or rod. just have to know the engines limits

[@Cal3b587]

​@jacklivingston4182 the valves start to float at 5500rpm as long as you don't pin it for extended periods of time your good

[@LovejoyBoi785]

Y’all gonna. Blow the motor without removing the governor

[@slurpe8357]

What all have you done to the bike

[@theclaytonshow838]

What about the linkage underneath the gas tank?

[@Its-Steven]

Holy fuck dude, hold the damn camera steady!

[@altraveling7019]

Link to the carb?

[@andrew_the_coin_collector8584]

How do you install the fuel lines

[@elliottfilms6254]

Part 4:07 on my video there is a close up on the carb, there should be a brass nipple that you pith the fuel line around! And then hook it to you gas tank the same way!

[@davidhammond3721]

Whare can I get some

[@Kevin2valid]

Do I need that 212 for me to put a carb in my 100u stock?

[@zakrYAH]

What about the loose piece?That's attached to the governor on the top underneath the gas tank is that important Do you need that in a certain direction

[@buddahmayne9273]

Most people remove the governor

[@Yumm-qk2lk]

After removing the govenor and governor arm theres a decent sized hole that might be a pain in yhe ass to remove

[@xptics]

just take off all the linkage and the arm and leave the governor in the engine that’s what i did

[@trokiandokeh1836]

Do i need to rejet it or is it already good for stage 1

[@cuh_2023]

You will need to reject it to like a 120 or 115 jet

[@perkututperkutut8725]

wanted to buy or purchase intake manipol 6 unit (manipol) how much?

[@montiel33b]

Do you with that hose on the bottom I didn’t see you hook it up to anything

[@richardhammah9887]

would this work on a stock massimo mb200

[@elliottfilms6254]

Yes it should work, just make sure you get the correct size carb.

[@janiceuga8785]

hm ,package deal ?

[@madshaman3911]

Whats the link to the parts

[@crybabylocr4012]

Did put on braket for after or no ?

[@crybabylocr4012]

Because I'm stuck I can put everything else on but stuck when it comes to throttle what do I do after I put carb and gas line on I just unhook old throttle and hook new one up to carb and it will work 🤔 ps I have 79 cc predator egine very simple

[@elliottfilms6254]

You might need a different throttle cable to match carb!

[@Hitech82]

Nice work son..

[@chrismitsven8544]

What kit is this?

[@carlosfrances01]

Fuel lines ????

[@B4N4N4-1DK]

Yes on the predator

[@noturtleleftbehind2242]

did u have to remove the internal governor for the new throttle set up

[@chrishall1025]

That’s what I’m wondering did you ever figure that out?

[@ItsLando]

@@chrishall1025 No u dont need to remove the governor inside

[@Mattydaddy80]

@@ItsLandoso how did you connect it to the carb?

[@ItsLando]

@@Mattydaddy80 the throttle cable goes into the carb so the throttle linkage on the predator isn’t being used so u can just take that all off and the governor arm isn’t being pulled with all that linkage so the governor just didnt kick in my bike does like 60 with the mikuni and the governor is still inside the motor 🤷🏻

[@Mattydaddy80]

@@ItsLando so is the governor arm just sitting there? It doesn’t affect the engine at all?

[@richardgordon3202]

My guy slow the camera down next time, all over the place

[@CrazyJoker48]

Why in the world are you using a crescent wrench? lol Do you not have a ratchet and socket set? Fixed end wrenches or even a ratchet end wrench! Crescent wrenches should only be used as a last resort when nothing else is available! They will strip the heads off a nut in an eyeblink! The 2:46 mark for example...I don't even have one in my collection because they cause more harm than help! You're a rookie in this video I can tell by that alone! But we all have to start somewhere! I'm sure you've grown wiser by now!

[@561jitt]

Can I put it on there without the extra manifold😂? I juss don’t like how it sticks out

[@xptics]

won’t get a good seal, plus the cylinder head gets really hot and the intake helps mediate that

[@gr3513]

Would this work on a honda clone? I got the bt200x. I always find videos but every vid I watch they have a predator 212 engine

[@elliottfilms6254]

Yes it should if the bolt patter is the same!

[@gr3513]

Thanks for the quick response brotha looking forward to your next vids

[@jasonjulian1]

It'll all work perfectly on the bt200x or any Coleman mini bike .
I juet installed a vm22 and adaptor on my rb200, basically identical.

[@Trains_n_stuff08]

Did the carb you got needed to be re jetted

[@elliottfilms6254]

No it was perfect

[@Trains_n_stuff08]

@@elliottfilms6254 oh ok thanks

[@slim2peezy281]

@@Trains_n_stuff08 I would suggest jetting them so they won’t bog at full throttle

[@jaydenmcmillen6748]

What jet did you run?

[@Cal3b587]

I'm running a 110 jet on my lifan 196cc with a straight pipe and it runs good

[@mikiecastro3957]

Will this fit on tilly 212

[@viceanime7685]

it should theyre all basic honda clones

[@troyholland3436]

Can I do this with out removing the Throddle linkage???

[@cuh_2023]

You don’t have to but then theirs just useless part on the engine

[@Tmask32]

So what do you do with all the other linkages??

[@daejuan282]

you don’t need them

[@J_ake]

can i just use the stock throttle cable?

[@jacklivingston4182]

yes

[@deutschlandgaming407]

Need help at 2:39 what size nuts do you put on the exist bolt?

[@Geneva_suggestions]

My size

[@teshuvahemmet3036]

Good job 👍

[@Dwp911]

What size fuel line did you use ..thank you in advance

[@Tota1Everything]

Should be 3/8s

[@elliottfilms6254]

It should 3/8. It also depends on the carb!

[@mohamadalhennawi842]

Do I need to remove the govonor 😅

[@danielclouse1546]

if your building a go-kart or mini bike its really up to you the governor makes it so it cant go to max rpm rated for the engine so not you don't need to but its recommended to remove it and if you decide to I recommend upgrading the valve springs I put 22lb springs in my Honda gx 160 and it ran great I have since retired it but it ran amazingly

[@Fiatfan]

Where did you get the air filter?

[@TeddyLoaf]

i got the same thing as him but black, amazon, it comes with the carb

[@trokiandokeh1836]

I have a stage 1 exhaust and a tc do i have to get another jet or is it adjustable

[@elliottfilms6254]

You shouldn’t need another jet unless you are running a bigger engine or a different fuel line size.

[@Cal3b587]

Yeah throw a 110 jet in it if you have a different exhaust or else you'll run lean

[@Deucealive75]

@@Cal3b587 Others need to tune to their engine and environment. A 110 jet worked for you but may not work for others. My stock 196's with a header pipe and silencer ran best with a 120 main. My built 196 likes a 125 main jet.

[@christopherflores6751]

Hi what carburetor is this I am trying to buy it

[@danielclouse1546]

YOXUFA VM22 Carburetor Carb

[@antoniojaime4253]

Both of my bolts got stuck bro

[@david-bx1ox]

At that point, just buy an actual Mikuni carb

[@stonerboiphoenix8732]

Can I put that carb on a 49cc engine

[@Ypn_m5]

no

[@Frank_336]

Will it go on a carter brothers go kart

[@Cal3b587]

Does it have a gx200 clone engine?

[@brokeblackguru9344]

Only ONE word for today: DIZZYING!!!😢
RalphyNovotney
The BrokeBlackGuru

[@fadefrees3729]

Did it crank tho 🤣🤣🤣

[@joelmccall5665]

Where do you get the kit from?

[@elliottfilms6254]

Amazon

[@Hareelevio]

​@@elliottfilms6254 could you send me a link if you can

[@danielclouse1546]

YOXUFA VM22 Carburetor Carb

[@YourBasicRat]

How do you take those rods out tf

[@Cal3b587]

Put two nuts on the rods then you then you can just use a wrench on the first nut to unscrew it

[@richardramirez-st8nc]

Did it work ? Haha

[@cesarcabanillas9333]

Must be nice having to order the black one they won’t ship red or gold to California🤦‍♂️

[@elliottfilms6254]

Ah darn!

[@blakesmith9632]

Deal with what you got bro

[@pedroferreia974]

@@blakesmith9632 literally no reason to comment that but Ight

[@timothykiniris1724]

​@@pedroferreia974he isn't wrong tho. Like fuck dude all he has to do is order a red air filter off Amazon

[@zachfloyd4049]

Dont live in California then

[@chevylandtv670]

Can you drop a link to the carb

[@elliottfilms6254]

www.google.com/search?q=mukini+carb+mini+bike+FVRITo&ie=UTF-8&oe=UTF-8&hl=en-us&client=safari

[@Ghost88890REAL]

hey we have the same build with a chikuni carb!

[@313_darnell2.0]

Does that carb make your bike a little faster ?

[@Ghost88890REAL]

@@313_darnell2.0 it should, the chikuni (if jetted right and no damage because it’s easily fragile) basically adds more fuel and air than the stock engine does

[@slim2peezy281]

@@313_darnell2.0 yea but all gearing is a big factor

[@noturtleleftbehind2242]

did u have to remove the internal governer

[@Ghost88890REAL]

@@noturtleleftbehind2242 yes

[@jimmartin9440]

The background music is annoying, why have it?

[@Tokyo816k]

I hate when peoples make videos and don’t show everything

[@user-cc1tm1bh7w]

ngl bro it’s a pretty straight forward assembly

[@ancientdebris7102]

Yo did it Fr add +20 mph from stock

[@ancientdebris7102]

Also what jet did you use? Thx

[@elliottfilms6254]

Yesss it was look at the end of the video I have the before and after also a torque converter adds a lot of power!

[@elliottfilms6254]

I used the jet that came
With it it worked great

[@Cal3b587]

​@@ancientdebris7102 I have the same kit with a straight pipe I have a 110 in mine

[@americandad4864]

Can’t hear because of the music .

[@norcal8718]

Snore 😴

[@emu55]

not a real mikuni

[@rogerrose8220]

Yup!

[@charliewilliams8026]

What do you mean it says mikuni on it

[@Tahmanakki]

@@charliewilliams8026 😂

[@jeremymartin8857]

Probably already know ,it works just as good and less $ . No brainer to get the knock offs

[@emu55]

@@jeremymartin8857 they work the same until they completely break…

[@picklekondor791]

What do you do with the extra black tube hanging out the bottom

[@wonderingwildling2598]

Zip tie it to the frame and angle it down towards the ground, or you can connect it to a catch can and strap the can to the frame but it doesn’t matter either way.