This is an amazing mod! I'm wondering why the metal tube is much shorter than in your previous mods. Do you get the same fps on all four darts? Does the first dart really shoot because the other three push it out?
metal tube i cut correct length for this, i i donot have test machine ,but looks not very obvious diffrent, yes the first one can shot normally,cos the whole lenght longer then 4 darts a little bit ,
Built it and it works! I had not realized that you must lower the gun (or just give it a shake) to load a dart. I was confused for some time. Once I watched tutorials on how an inline 4-shot clip works, I understood. All four darts shoot at about 80 feet per second. Lots of sanding down and filing the parts from the 3D printers, especially the o-ring mount on the dart door slide. If it isn't a firm fit, it will unseal when a dart is fired.
I've searched for a better springer pistol and I honestly think this is the best one. A Rival Knockout inline-4 mod is a close contender because the plunger tube is larger, but without the silencer, this pistol is short and effective. You can stuff it into any cheap drop holster you can buy and have it ready in case your primary jams. I must be getting 100 feet per second on the 1st dart and 120 feet per second on the 2nd to 4th. I'm using a Retaliator 9kg spring. I watched Captain Xavier's BigShock "Can it take a K26?" video and his Spring Removal video to learn how to swap it. The plunger head is well-cushioned. Plumber's thread seal tape is very cheap and you'll need to put a couple of winds of it under the plunger head o-ring to give it a tighter air seal to the plunger tube. I also put as many winds as I could on the thinner diameter section of the 3D-printed inner tube (1:40) so that it can still slide in with a tight fit. I use duct tape on the thicker diameter section to friction-fit it into the BigShock. I used a lot of superglue on the printed ring (1:50) to seal any air leaks with the BigShock. I think I would wrap some thin amounts of threading tape on the printed ring before gluing inside if I did this again. I don't bother putting the handles on (4:50) because the air pressure is too strong from each shot. I keep the dart door held tight against the blaster with my thumb.
I would like to see a mod kit for the strife that doesn’t reduce performance. I can’t find cheap mod kits for the stryfe. This is only a suggestion, you don’t need to do this.
This is an amazing mod! I'm wondering why the metal tube is much shorter than in your previous mods. Do you get the same fps on all four darts? Does the first dart really shoot because the other three push it out?
metal tube i cut correct length for this, i i donot have test machine ,but looks not very obvious diffrent, yes the first one can shot normally,cos the whole lenght longer then 4 darts a little bit ,
Built it and it works! I had not realized that you must lower the gun (or just give it a shake) to load a dart. I was confused for some time.
Once I watched tutorials on how an inline 4-shot clip works, I understood. All four darts shoot at about 80 feet per second.
Lots of sanding down and filing the parts from the 3D printers, especially the o-ring mount on the dart door slide.
If it isn't a firm fit, it will unseal when a dart is fired.
I've searched for a better springer pistol and I honestly think this is the best one.
A Rival Knockout inline-4 mod is a close contender because the plunger tube is larger, but without the silencer, this pistol is short and effective. You can stuff it into any cheap drop holster you can buy and have it ready in case your primary jams.
I must be getting 100 feet per second on the 1st dart and 120 feet per second on the 2nd to 4th.
I'm using a Retaliator 9kg spring. I watched Captain Xavier's BigShock "Can it take a K26?" video and his Spring Removal video to learn how to swap it. The plunger head is well-cushioned.
Plumber's thread seal tape is very cheap and you'll need to put a couple of winds of it under the plunger head o-ring to give it a tighter air seal to the plunger tube. I also put as many winds as I could on the thinner diameter section of the 3D-printed inner tube (1:40) so that it can still slide in with a tight fit. I use duct tape on the thicker diameter section to friction-fit it into the BigShock.
I used a lot of superglue on the printed ring (1:50) to seal any air leaks with the BigShock. I think I would wrap some thin amounts of threading tape on the printed ring before gluing inside if I did this again.
I don't bother putting the handles on (4:50) because the air pressure is too strong from each shot. I keep the dart door held tight against the blaster with my thumb.
There is a problem with previous video, image shake . so Re-upload here. Friends who have watched it can ignore this , sorry~~~~~~~
can you share the file to the 16mm barrel version of the inner tube like the one you used in the video
Could this not work as a six shot with that suppressor?
This mods look really nice
yes,the design very good😁
Whats the barreling material used in this video?
16mm aluminium barrel
where did you get the big orange muzzle that's shown at 0:30
oh ,its the dart zone mk2 muzzle,just fit perfect this one😁
I can’t wait to make my own mod kit
just do it😁
Could you link the o ring please
what fps can i get on this mod?
hi, i am not sure bro, but looks almost same as mega transfer to elite directly.
I'm getting 80 - 90 fps with the stock spring
Now getting 100-120fps with a 9kg Retaliator spring and all air-leaks prevented with thread tape.
Where did you get that sweet silencer?
hi, its Worker s product
bonjour c est quel type le tube que vous mettez dedans merci
hi,you mean the metal one? its WORKER stander tube id 13mm,od 16mm
@@ZDLSPACE thanks you
aw man i wish i have a 3d printer :(
多谢分享,这个好漂亮啊~ 请问螺丝应该用什么规格的?
谢谢,我忘记了,手上螺丝太多了,好像是普通的m3,希望没记错
@@ZDLSPACE 收到,多谢~
i have printet me this kit but i dont know hoe to put the silencer behind the stopper
i have made some change on innner tube,i have 3d file,if u want,let me know ur email,i sent to you😁
@@ZDLSPACE I would also like the file if possible
感覺最麻煩的莫過於金屬管的部分?
不曉得用塑膠管行不行
我猜呀,只要足够光滑的应该可以,之所以放金属管,是因为打印件表面太不光滑啦.
@@ZDLSPACE 原來如此,我以為是因為金屬管比較堅固、穩固,塑膠管太軟沒辦法
@@貓東巴 哈哈 那里都不受力的,无需太稳固,保证内径正确就可以上.
@@ZDLSPACE 了解 謝謝解答
I happen to have a mega bigshock and a friend who can help me print.
can i buy the kit from you? i cant find a local 3d printer :(
aha you stay in Singapore?
@@ZDLSPACE no i stay at indonesia
@@AzzamSukaMobil just come back from Bintan😄
@@ZDLSPACE was it nice?
請問金屬管需要用多長?
用我改过的那个管子,需要使用31mm金属管.
請問下是如何一發一發的打出來的呢?
我复制一段别人讲解的话哈:“应该是第一发顶在缩小的出口上密封住,后三发空间大,空气绕过了。视频中提到第二发需要整体朝下,应该就是让后面的软弹顶到前面密封住出口。” 不知道能看懂不😁
太帅了
😁😁😁
這樣改也太帥了吧
谢谢呀,这个改件设计的挺好😁
I would buy a printed kit from you, I dont have access to a high quality 3d printer.
hi ,i think download 3d file from Thingiverse,then find a local print service is better~
halllooo
😁😁😁ni hao
@@ZDLSPACE 你好!我的中文进步了 still not very good at the ping ins stuff put I have speaking nailed! 😅😆
I would like to see a mod kit for the strife that doesn’t reduce performance. I can’t find cheap mod kits for the stryfe. This is only a suggestion, you don’t need to do this.
i see lots of worker product for stryfe ,plastic and 3d printed. like kriss🤣
@@ZDLSPACE yeah, but they are extremely expensive
@@bigbodyboy2193I think your best bet is one of those knockoff stryfes or try make on out of cardboard