Це відео не доступне.
Перепрошуємо.
224 212 governor and oil sensor removal
Вставка
- Опубліковано 22 лют 2022
- In this video we go step by step and completely remove the governor and oil sensor in a 224cc predator. This process will work and any of these Honda clone engines.
Amazon Affiliate Links
Metal Coat Hanger
amzn.to/3wS7cnv
1\4 20 Bolt For top Governor Hole
amzn.to/3GgfV7f
1\4 20 Tap
amzn.to/3sTvfkM
#7 Drill for 1\4 20 Tap
amzn.to/39Ty8ep
1\2 13 Bolt For Oil Sensor Hole
amzn.to/3LK2MUP
1\2 13 Tap
amzn.to/3LLZMYh
27\64 Drill For 1\2 13
amzn.to/3LR067T
VM22 26MM Crab
amzn.to/3wNNFUY
VM22 26MM Carb Main Jet Kit
amzn.to/3wNmpWz
224 Billet Flywheel 6689
amzn.to/3PFeLqc
18Lb Valve Springs
amzn.to/3lFqKq0
Arc 212 Hemi Billet Side Cover
amzn.to/3wERewA
Side cover Unvented
amzn.to/3z40Aoq
Crankshaft oil seal
amzn.to/3LKbqmc
212 .010 Head Gasket (May Need To Open Holes For Dowel Pins)
amzn.to/3MLvPZr
OEM 212/224 Non Hemi Head
amzn.to/3MLBFu3
ARC Racing 212/224 Cylinder Head for Clone - HI COMP 14cc
amzn.to/38hHpwH
Predator 212 Non Hemi Stainless Steel Push Rods
amzn.to/3Nv2Qcq
30 Series Torque Converter
amzn.to/3m0GOCV
Centrifugal Clutch
amzn.to/38gABiI
Coleman Jackshaft
amzn.to/38gABiI
If you cut the governor arm above the clip notch you can slide it out without removing the crank. You can then cut it again at the 45° but leave the ears on it so you can remove the burs and slide it back in and use the factory clip to secure it.
That is an excellent tip! I never thought of that!
I'm going to pin this comment hopefully people will see it!
Thank u bro, 😊outta all the videos I watched on UA-cam your video is the BEST in details and explaining the whole process in doing the governor and oil sensor removal.
Awesome man thanks alot!
48 ain't bad dude. I'm sure the more u do the faster she'll get! Informative thanks man
Right on man thanks! Next is a mikuni knock off sitting on my table already!
Lot of work just for removal, but I do appreciate the education on it for possible future projects.
It seems like a lot of work but it's not really to bad.
This video is excellent.
Hey thanks I appreciate that!
@nicsminibikes i am using your advice. Your use of the throttle lever is perfect
Thanks brother I followed your guidance man thanks again
Right on! I try to make easy to follow videos. Some are harder to make then others!
Great video👍👍
Thanks!!
Good job 👍
Thanks I tried hitting on as many things as I saw people asking for help with and this was a big one!
Very good video
Thanks! I appreciate it!
Does removing the ring gear for the governor increase the end play on the crank?
Nope, there is a shoulder on the crank that takes care of the end play.
Would incorrect value clearance cause the motor to not start
Yes it could or at least run really bad
Was able to follow the video well but when I got to removing the crank shaft I can’t get it out? Does anyone know what it can be stuck on? I took rod off and now the crankshaft will move forward and backwards a bit. But won’t budge all the way out.
Cam is out I would imagine and piston is pushed all the way to the top and flywheel is off? U'll have to look inside and make sure the crank balance weights are not hitting anything
@@nicsminibikes the cams out, flywheels off, piston didn’t wanna go into the top after taking rod off but then I got it pushed up but crank still wouldn’t wanna come out. I’ll check the weights next. Cause I’m not sure why else it wouldn’t come out
@@jonathanhurst5904 ya it should just slide out. U can also maybe get in there with something to cut the hockey stick looking end off and not need to remove the whole crank. If ur pulling the whole top governor rod out and plugging the hole u can cut the part of it that sticks out the top and u should be able to get the rod out but u won't be able to set the the throttle up like I did in the video.
I don’t have anything to cut it with unfortunately. I tried just pulling the gov arm out without taking crank off but it would get stuck on the crank right before it was all the way out.
@@nicsminibikesand I’m putting new carb on so I won’t need any of the throttle assembly stuff afterwards
How fast does a 224 go stock with this governor removed?!
Probably around 30-35 also will depend on your gearing
How risky is taking the governor off on a stock 224cc and will it make it less risk of blowing the engine if I get 18ib valves springs?
Adding the 18lb springs will help to not have valve float. The motor will Rev higher without the governor. I highly recommend billet rod and flywheel with a governor removal.
@@nicsminibikes how much and where could I get those tho I’m 16 so I don’t have a lot of cash lol
@@smokey4002 go check out my 224 build videos links to parts will be in those video descriptions
@@nicsminibikes thanks I’ll check it out
@@nicsminibikes man I want to bite the bullet and buy a performance kit for my 224 but I’m afraid of clearancing, I’ve never done it before and I’d hate to mess up
Can't hear ya
Well that's a bummer the sound is good on my end when I play it on UA-cam. I don't know?
@@nicsminibikes i think he's just deaf
@@PseudoGuido lol I don't know I've been told a few times my audio is quite