Це відео не доступне.
Перепрошуємо.
PnPduino Honda OBD1 B/D Standalone ECU
Вставка
- Опубліковано 12 сер 2024
- This is the first of many Plug and Play Standalone ECUs for our beloved JDM engines. This is based on Speeduino firmware and UA4C board, which connects directly to any Honda B/D engines without ANY modification.
Please visit www.pnpduino.com for more info
Great job....
Well done sir!
Great work! Now I want one for K series engines
will be available soon!
Sana, soon pang Toyota 3SFE, OBD1 nman😁
4EFTE pa surr
High very interested i emialled via thanpho tuning
What baseman is being used ? Is it just plug in and it will run the car??
When is there a new stock coming
Will this support Alpha N? Very kool, I like the idea of modern electronics. I lost a p28 because the capacitors started leaking. Hondata is going to have to lower their prices if you get a distributor in North America
Hi. Yes, alpha n is supported. Will be available next year due to revisions. Thanks!
Hii, great job sir..
I very interest to your project.
Regarding the knock sensor is working properly on this PnPduino?
Hi. The knock control is already in the firmware, just not implemented.
Stock honda distributors have 3 sensors (CKP, TDC, and CYP). Does ECU use all these sensors to run the engine?
Hi. Only CKP and CYP is being used by PnPduino
Can you tell me if this is a complete plug and play for obd1 hondas? Do I need to download a baseman to get my car running or how about injectors offsets and what not when boosting ? Will this ecu plug in and require no modification to crank sensors or dizzy?
Hi. yes no need to modify the crank sensors or distributor. you can also adjust the injector dead times from Tunerstudio
On the wide band you no longer have to splice into d14 to connect wide band or how did you connect wide band im confused on that part boss
There is a dedicated onboard connector for the wideband. If you use that connector (its provided), no need to splice. Just calibrate within the software. You need to disconnect the oem o2 sensor if there is
Can I buy the parts case/obd1 adapter/ special vr conditioner and build myself?
hi. sadly no sorry
Will it work with obd2 with obd1 jumper harness ?
Yes, but make sure the obd2 to obd1 jumper harness is a good quality, not from the cheap chinese copies. we have experience that the pins do not contact properly, specially the ground pins
Could the honda tuning suite software be used with this also?
Hi. no, only tunerstudio
Do you have a PnP ecu for 4age 20v blacktop?
Yes we have! check on the website
Can it be used for H series?
Yes, but I don't have an H series engine to confirm it. if the pinouts are the same, then it should work.
How to get the adaptor board
Its in my website www.pnpduino.com, but currently out of stock
magkano
hm
when u get stock
Hi. Hopefully before the end of december. Thanks
Speedy is a great product, but for these obd1 Hondas a chipped ecu is king...
Agree, as long as they are working. I have 2 obd1 ecus not working anymore
@@choyr You can try replacing the caps, they go bad with age. you can also use automatic ecus and convert them to vtec manual etc
@@turboimport95 already tried it, but its not from the caps and not worth it to find where is the fault
Tried to contact with you but not luck, let me know! Thanks
Hi. you can check the website to contact me. Thanks!
@@choyr sent you already a +1 week ago and not reply.
@@Walterronny hi. Can you send an email again?
@@choyr Sent.
How much to buy one ?
Hi. Its $400 for the complete ecu