My wife walked in during the blow and suck portion of your video. It was awkward. Very informative video! This helped me find my leak after a local dealer told me I had a cracked cylinder.
Thanks, Mower Medic 1! That's the engine I have on my Cub Cadet XT2 tractor style rider. Although I've never had any trouble with it, this tip is really great to know!
great troubleshooting technique, appreciate it it. I have an older 2011 600 fr600 20 hp and it is leaking oil everywhere will take a look at that thanks!
Great tip! I have a Hustler Raptor with the Kawasaki Fr619v and was curious if that engine is also prone to the same issue and it's a 2015 model 23 horsepower I believe
Hey I liked your video, my FH680D is leaking like a cive. I changed out the breather gasket twice now, still leaking after I run it a few times. I think there must be a lot of pressure for it to keep blowing past the gasket, any ideas of what I need to do? Thanks
where do we get the updated kit again ??? and is other items on this motor to update with better parts ? is there a pan gaskit that better than factory ?
Thanks for the info. Should help a lot of people. I run a lot of kawasaki's but most of mine are FX series and a little bigger aren't the 481's around 15 HP? The smallest one I'M running is a FX651V and a FX850v carburetor would these engines have this same problem?
Would this apply to the Kawasaki 15 hp FH451V engine as well? First time into this exMark Metro. 48” walk behind…. left side (oil filter side) is leaking oil coming off the back of the shroud. Replacing valve cover gasket and starting it up and observe. Hint - It really starts to piss oil once its been operating for 10 minutes. Thx Anyone!❤❤
I have an FV500 that i just did this upgrade on. It did not have the reed valve. How does the vent work and how can I test it properly? Thanks for any info you can provide.
Great video, thank you. Fairly certain mine has the same issue, was mowing, suddenly felt as if it bogged down so I cut the unit off. I looked under the mower, nothing underneath but smoke pouring out if filler tube. Guess it finally got to hot and engine died. Anyone to know for sure that if I do this repair it's going to start back up?
Do you see upper bearing failure on early FH680V engines? I have a 1999 (400 hours), around 2001 they sent me a revised dipstick (more oil). Apparently there is no oil hole for the upper bushing on the early ones. Oil level is very important.
I've got oil coming out of my breather tube, a little, I have it off my air filter so oil dont go into my carb, is that ok till I do what you did? Thanks
I've had a few of these come in with oil in the filter and carb, the reed valve fails and the engine pressurizes and has oil bleed back thru the bypass tube into the filter.
I’ve got the same motor, and at this point I am just trying to get it running. I cleaned it with a pressure washer, and just sitting there it leaks oil from who knows where. (The valve cover gaskets are dry) any suggestions? ( haven’t started it yet
I can't speak for mower medic but it depends on what I'M cleaning. I think brake cleaner does a better job of cleaning up oil and other debris but it can effect some plastic and rubber materials so on those i use carb cleaner
My wife walked in during the blow and suck portion of your video. It was awkward. Very informative video! This helped me find my leak after a local dealer told me I had a cracked cylinder.
Lol gold
you're the man...not sure if its the exact problem I've got but you probably saved me a ton of headache trying to diagnose. thanks for posting
Thanks, Mower Medic 1! That's the engine I have on my Cub Cadet XT2 tractor style rider. Although I've never had any trouble with it, this tip is really great to know!
great troubleshooting technique, appreciate it it. I have an older 2011 600 fr600 20 hp and it is leaking oil everywhere will take a look at that thanks!
really good information Jeremy, thanks
Thank You for information and advice
Thank you very much! 👍
Thanks for the smooch technique.
Great tip! I have a Hustler Raptor with the Kawasaki Fr619v and was curious if that engine is also prone to the same issue and it's a 2015 model 23 horsepower I believe
Great diagnosis. Oil leaks can be hard to find especially if they are slight leaks. Thanks for the tips.
Hey I liked your video, my FH680D is leaking like a cive. I changed out the breather gasket twice now, still leaking after I run it a few times. I think there must be a lot of pressure for it to keep blowing past the gasket, any ideas of what I need to do? Thanks
Great job. You can also use a presure vacume tester insted of using your mouth.
Vac tester doesn’t produce the volume of air needed to perform the Test effectively
Good stuff, man. Thank you for sharing. Don't think I've ever worked on one quite like this, but it's good to know.
Good to know for an old fogie like me. Thanks!!
where do we get the updated kit again ??? and is other items on this motor to update with better parts ? is there a pan gaskit that better than factory ?
Turns out it wasn't my problem but thanks for the great video. I had the other common, easy to fix Governor shaft seal leak
Can't find your Kawasaki flywheel removal video. Can you give me a link?
Thanks for the info. Should help a lot of people. I run a lot of kawasaki's but most of mine are FX series and a little bigger aren't the 481's around 15 HP? The smallest one I'M running is a FX651V and a FX850v carburetor would these engines have this same problem?
Where did you get you update kit from . Video was great.
My engine FH680V failed the suck test. Almost no resistance even sealing the hole there is no resistance. what should i check next?
Great to know. Thanks 👍
thanks for the info helped me out.
I just had a surging problem after changing the carburetor. All I can say is don't forget the pcv hose under cover by fuel pump.
How about a link to Part 2?
Would this apply to the Kawasaki 15 hp FH451V engine as well? First time into this exMark Metro. 48” walk behind…. left side (oil filter side) is leaking oil coming off the back of the shroud. Replacing valve cover gasket and starting it up and observe. Hint - It really starts to piss oil once its been operating for 10 minutes. Thx Anyone!❤❤
I have an FV500 that i just did this upgrade on. It did not have the reed valve. How does the vent work and how can I test it properly? Thanks for any info you can provide.
Would that cause one of these engines to surge and and run rough
Good video as usual. Any tips on a leaky gov shaft seal on an fs481. I have replaced seal and still is weeping oil from the seal, thanks
I had the same problem and it was the crank seal ..thanks
WalMart has the best price I have found for Brake Clean... just under $2 a can (14.5oz, the flammable kind [not sure if that's chlorinated or non]).
Great video, thank you. Fairly certain mine has the same issue, was mowing, suddenly felt as if it bogged down so I cut the unit off. I looked under the mower, nothing underneath but smoke pouring out if filler tube. Guess it finally got to hot and engine died. Anyone to know for sure that if I do this repair it's going to start back up?
Do you see upper bearing failure on early FH680V engines? I have a 1999 (400 hours), around 2001 they sent me a revised dipstick (more oil). Apparently there is no oil hole for the upper bushing on the early ones. Oil level is very important.
I've got oil coming out of my breather tube, a little, I have it off my air filter so oil dont go into my carb, is that ok till I do what you did? Thanks
Have you ever tried the cans of gasket remover?
I've had a few of these come in with oil in the filter and carb, the reed valve fails and the engine pressurizes and has oil bleed back thru the bypass tube into the filter.
I’ve got the same motor, and at this point I am just trying to get it running. I cleaned it with a pressure washer, and just sitting there it leaks oil from who knows where. (The valve cover gaskets are dry) any suggestions? ( haven’t started it yet
Great info and video.
Man I need your help I lost my breath valve is there anyway I can communicate with you to get some advice.
Right here what ya got?
Guess he found it lol
Would this be similar for Kawasaki FX600V?
Mower medic do you like brake cleaner better then carb cleaner?? And why?
I can't speak for mower medic but it depends on what I'M cleaning. I think brake cleaner does a better job of cleaning up oil and other debris but it can effect some plastic and rubber materials so on those i use carb cleaner
@@nashguy207 I agree.and it's harsh on paint as well. so I use brake clean most of the time
Do you recommend honing out an aluminum cylinder on a small engine?
Yes I use a dingle berry hone
You don't recommend the flexible 3 stone deglazing hone?
Cool
did you get the email I sent you?
Great video god bless
Why don't you make your own gasket?
No thanks I only make gaskets when one is no longer available