Replacing the fuel fitting on a BMW R 1200 GS

Поділитися
Вставка
  • Опубліковано 17 січ 2025
  • There are two assemblies on the outside of the fuel tank on a 2005-07 BMW R 1200 GS that make sure gas gets to where it needs to be. Both come equipped from the factory with cheap, crappy plastic quick disconnects that break sooner or later.
    Mine broke later, at about 86,000 miles, but the kicker is it wasn't the original one. It was part of an assembly that was replaced due to a recall.
    At any rate, in this video you'll learn how to replace the fuel fittings in question, as well as how to siphon gas out of the tank and remove and fit the side panels.
    Tools needed:
    Needlenose pliers
    Special tool for removing housing ring
    T25 Torx driver to remove body panels
    Other various tools (mentioned or seen in the video)
    Parts came from Beemer Boneyard (www.beemerboney...) and the kit for my bike cost $82.95. Always look up your part numbers before buying parts and ensure you're getting the right stuff!
    Check out Motorcycle Test Kitchen! right here on UA-cam for product review videos and visit the MOA website at BMWMOA.org. Enjoy!

КОМЕНТАРІ • 26

  • @cypilotiowan4761
    @cypilotiowan4761 Рік тому

    GREAT video. My ‘05 GS developed a leak on my right leg. Got the kit from BeemerBoneyard and had it fixed in 30 min, which included a cold beer.

  • @donaldelliot8490
    @donaldelliot8490 2 роки тому +2

    Word of warning, on your plastic fairing, the 1/2 turn inner front one, change it for a screw (mine flew off at 70 mph) it hurt my knee like hell!
    Lovely fuel fitting job, great videos (I would love to see the out-takes) 😂🤣🇬🇧

    • @BMWMOAorg
      @BMWMOAorg  2 роки тому +1

      The outtakes for this one involved a lot of gas on the floor in FEBRUARY!! :)

  • @tonybaumgartner6014
    @tonybaumgartner6014 4 роки тому +1

    This is a really helpful tutorial on BMW. I love my 2008 R1200RT but it has been to the shop three times for this problem. I am going to do the work myself this time and buy the
    stainless steel part. Why did the dealer replace one defective part with another defective part as evidenced by its failure. Good tips in the video. Thanks

  • @rafalozy4648
    @rafalozy4648 2 роки тому +1

    You help me to solve the same problem :). Thx Guys

  • @howhelovesusall
    @howhelovesusall 2 роки тому +1

    When I pulled the fitting out a piece of the inside wedged itself in the opening. Will the ez thread out work to retrieve that piece, or will it fall into the tank? Thanks

    • @BMWMOAorg
      @BMWMOAorg  2 роки тому

      In my experience, you always have to be careful with EZ-out type tools to ensure the debris doesn't fall the wrong way, but if it does, it's easy enough to shake it out of the tank.

  • @colinl1597
    @colinl1597 2 роки тому

    Hi great video. Can you tell me the name of the thread sealant. Thanks

    • @BMWMOAorg
      @BMWMOAorg  2 роки тому +1

      GASOILA Soft Set with PTFE Premium Thread Sealant

    • @colinl1597
      @colinl1597 2 роки тому +1

      @@BMWMOAorg Thanks 👍

  • @ShedOfDreams
    @ShedOfDreams 4 роки тому +1

    Nice. Useful info. Thanks for bothering. Hope the bike is more reliable for you.

  • @attilapal8490
    @attilapal8490 Рік тому

    Hi. I beg you. what gasket did you use for the thread???? well thank you

    • @BMWMOAorg
      @BMWMOAorg  Рік тому

      I used what Beemer Boneyard supplied in the kit, but any gas-proof threadlock will do the trick.

  • @johnbalkenbush6374
    @johnbalkenbush6374 3 роки тому

    Great video! Can you tell me what size easy out you used to remove the broken fitting?

    • @BMWMOAorg
      @BMWMOAorg  3 роки тому

      John, I'm sorry but I don't remember any more what size it was.

  • @MentallFloss
    @MentallFloss 2 роки тому

    Hello I'm in the process of doing the same thing on my 2010 RT and accidentally broke the flow shut-off valve of the female QD do you know if it can be replaced ?
    Thank you

    • @BMWMOAorg
      @BMWMOAorg  2 роки тому

      Hey there - yes, you can replace the QD. I don't think you can replace just the valve on it, though. Most likely you'll need to replace the entire QD.

    • @MentallFloss
      @MentallFloss 2 роки тому

      @@BMWMOAorg I watched another video and I think that shut off valve is a part of the QD, will check it later today. I thought i had to replace the entire pump because of this shut off valve, was dreading it. Thank you

  • @howhelovesusall
    @howhelovesusall 2 роки тому

    What size was the easy out tool?

    • @BMWMOAorg
      @BMWMOAorg  2 роки тому

      sorry - don't recall any more

  • @mattcero1
    @mattcero1 3 роки тому

    It seem liked I dropped a cylinder the other night and limped home on one cylinder. I checked all plugs and they all sparked as I turned the motor over with one out and grounded at a time and they all sparked. Do you think I'm having a fuel problem on my 2012 BMW R1200GS Adventure? Any insight will be much appreciated sir or anyone reading this. Thank you.

    • @BMWMOAorg
      @BMWMOAorg  3 роки тому +1

      Matt, you might want to check the ignition coils. You can get spark, but not enough to be effective if that makes sense. That would be my first guess without having the bike in front of me.
      Of course, it's been 5 months since you asked your question (sorry!) so maybe you figured it out by now? If you did, what was it?

    • @mattcero1
      @mattcero1 3 роки тому

      @@BMWMOAorg I was not getting good compression on the right side. This is after swapping coils and plugs and fuel injectors for T-shooting. When I pulled the head and filled it with gas, it was leaking through the closed valves. I checked the rings and piston after pulling the jug off and they "passed" clearance checks. I also bought the cam jig tool and retimed the valves after I lapped the valves with coarse then fine compound. It started right away after reassembly. I did buy a coil and fuel injector to test and will now have these as spares. I just got back from an 11 state, 10 national forest trip through the southwest and had zero problems with the engine. Thanks for your thoughts though.

    • @rizwankhan5822
      @rizwankhan5822 Рік тому +2

      Hi I have the same problem but on the left side all injectors and coils and plugs checked I think may be I should try what you did I gave up changing so many sensors with no hope

    • @mattcero1
      @mattcero1 Рік тому

      Mine ended up being the valve timing went out of adjustment. I took the entire offending head off and did a valve job (proper lapping) and put it all back together using a cam locking tool and a TDC locking pin when I torqued the timing gears down and it started right up. FYI. @@rizwankhan5822

  • @tangowiskey4740
    @tangowiskey4740 Рік тому

    I have a 2009 GSA fuel pumps and controller suck. My bike has definitely let me down more time than care to talk about. Fuel pump clutch ect ect. Wonder if was really made in china.