I don't want to sound too negative because this video was incredibly helpful but there are some major differences between these Grand Cherokee's and my 2014 Grand Cherokee. In my GC The lower ball joints are pressed into the steering knuckle. The sway bar bushings are molded onto the sway bar. Also, the upper control arm nuts can only be accessed from the engine bay. I did follow you step by step and the video was very helpful. There must be some regional or model year differences.
thank sir ... you can find in my channel ... Playlists ... U.S.A Cars ... i have there video for jeep grand cherokee 2014 ... thank you for watching 🙏❤️🔧
Rattle Over Bumps - if you have an older WK2 (mine is a 2015 with 100K) with original brake pads, your rattle could be caused by rusted mounting studs on the break pads. They make the little pressure mounting tabs out of cheap metal and they literally rust away with time and then allow the pads to make an annoying rattle over bumps (can occur on rear as well). I live in Cleveland, OH and dump a lot of salt on our roads, so if you go longer than say 5 years, and live in a similar environment you may have the same issue. Simple fix with new pads (although both my rotors and pads had another 10-15K in them). I have NEVER had a set of pads last longer than 35-40K - Jeep did a great job engineering the pads and rotors to match the WK2 (mine is V6)! When I went to replace them, I paid up to use MOPAR parts hoping to get same results again - don't mess with success!
hello sir ... I will be do that in the future .. but can watch this video ... ball joint in dodge charger looks like your jeep ua-cam.com/video/dxZlqe95g0M/v-deo.htmlsi=4owsB5OE5f6Ejeis And this ua-cam.com/video/UDoIXDS-QLk/v-deo.htmlsi=007w-9JFdxun0d0R and this ua-cam.com/video/YB1jJMlSwcs/v-deo.htmlsi=XUeL1U9ma2kx9g5H
One more comment, if you live anywhere, where cars rust don't try to remove the wheel speed sensor from the steering knuckle. Unplug it and leave it in the knuckle.
ما شاء الله، ربي يعطيك الصحة، في اختلاف في الموديلات لأن مسامير upper control arm في سيارتي يوجد به سن بارزة للتأمين ، يعني لازم تفتح الصواميل اللي تحت صندوق الفيوزات ، المشكلة ما عرفت كيف افك الصندوق خايف نقطع خيوط الكهرباء. رحمة على والديك ورينا مكان الصواميل بجهة الراكب و كيف نشيل صندوق الفيوزات
الله يعافيك و يحفظك و يرحم والديك اخويه .... اخي تقدر تبحث في قناتي عن تبديل upper control arm jeep ...اني افتحها من الداخل بأستخدام ( الكوسرة ) يعني اكسر سن التأمين .. لا تحتاج لفتح الصواميل من صندوق الفيوزات ... لازم تستخدم الكوسرة او درنفيس حاد لكسر سن التأمين و هذا لا يؤثر على السيارة ابد
I don't want to sound too negative because this video was incredibly helpful but there are some major differences between these Grand Cherokee's and my 2014 Grand Cherokee. In my GC The lower ball joints are pressed into the steering knuckle. The sway bar bushings are molded onto the sway bar. Also, the upper control arm nuts can only be accessed from the engine bay.
I did follow you step by step and the video was very helpful.
There must be some regional or model year differences.
thank sir ... you can find in my channel ... Playlists ... U.S.A Cars ... i have there video for jeep grand cherokee 2014 ... thank you for watching 🙏❤️🔧
Rattle Over Bumps - if you have an older WK2 (mine is a 2015 with 100K) with original brake pads, your rattle could be caused by rusted mounting studs on the break pads. They make the little pressure mounting tabs out of cheap metal and they literally rust away with time and then allow the pads to make an annoying rattle over bumps (can occur on rear as well). I live in Cleveland, OH and dump a lot of salt on our roads, so if you go longer than say 5 years, and live in a similar environment you may have the same issue. Simple fix with new pads (although both my rotors and pads had another 10-15K in them). I have NEVER had a set of pads last longer than 35-40K - Jeep did a great job engineering the pads and rotors to match the WK2 (mine is V6)! When I went to replace them, I paid up to use MOPAR parts hoping to get same results again - don't mess with success!
Thank you for the information 👍🏻🔧❤️
Great video. Curious why the tie rod end ball joint wasn't replaced while you had the whole suspension apart?
Because he was not harmed ... thank you for watching 👍🏻❤️🔧
Hey Ali. Can you please make a video how to change that ball joint on the steering knuckle? thank you!
hello sir ... I will be do that in the future .. but can watch this video ... ball joint in dodge charger looks like your jeep
ua-cam.com/video/dxZlqe95g0M/v-deo.htmlsi=4owsB5OE5f6Ejeis
And this
ua-cam.com/video/UDoIXDS-QLk/v-deo.htmlsi=007w-9JFdxun0d0R
and this
ua-cam.com/video/YB1jJMlSwcs/v-deo.htmlsi=XUeL1U9ma2kx9g5H
One more comment, if you live anywhere, where cars rust don't try to remove the wheel speed sensor from the steering knuckle. Unplug it and leave it in the knuckle.
you can clean that
Great Video. Thank you for not starting off with an autobiography and dumb music.
you welcome ... thank you for watching ... do not forget to subscribe to my channel ❤️🔧👍🏻
ما شاء الله، ربي يعطيك الصحة، في اختلاف في الموديلات لأن مسامير upper control arm في سيارتي يوجد به سن بارزة للتأمين ، يعني لازم تفتح الصواميل اللي تحت صندوق الفيوزات ، المشكلة ما عرفت كيف افك الصندوق خايف نقطع خيوط الكهرباء.
رحمة على والديك ورينا مكان الصواميل بجهة الراكب و كيف نشيل صندوق الفيوزات
الله يعافيك و يحفظك و يرحم والديك اخويه .... اخي تقدر تبحث في قناتي عن تبديل upper control arm jeep ...اني افتحها من الداخل بأستخدام ( الكوسرة ) يعني اكسر سن التأمين .. لا تحتاج لفتح الصواميل من صندوق الفيوزات ... لازم تستخدم الكوسرة او درنفيس حاد لكسر سن التأمين و هذا لا يؤثر على السيارة ابد
@@ALI_FIX12 الصامولة اتطيح من مكانها ، و نرد نفك صندوق الفيوزات ، اخي انا لست صاحب ورشة افتح و أغلق بيدي ما عندي عدة هواء مضغوط في المنزل .
تقدر تمسكها بمفك رقم ١٨ مع تطواله او من الاعلى تثبت المفك بالسيارة و تفتح من الداخل بدون ماتطيح الصاموله
عاشت ايدك شغل امرتب
اشكرك ياغالي ... شكرا على المشاهده ❤️🙏
Great video. Doing this on my wife’s car, does the rear mount have specific placement or alignment when pressed in to the lower control arm?
you welcome sir ... no effect ... thank you for watching 🔧❤️👍🏻
What year model and how many miles?
I think it was 2014 ... thank you for watching
where you located at?
iraq - baghdad city