Thank you so much for this video I am 72 years old and put this thing together by myself. I could have never done it if not for this video again thank you so very much😊
Just got the shed, yesterday and assembled it today, found the instructions simple and easy to follow, but for the hinges, took a bit to figure out which side is up, five minutes of playing around sorted it out nicely. Would appreciate some hints re fasteners to the base, either concrete or wood. All in all took about an hour to assemble.
Very helpful, especially given the written instructions are a bit wonky. At one point, it orders you to put a washer and bolt going in both directions in the same hole (?!). This clarifies the intent was just to put a washer on each side. The written instructions also say to put just two screws in the roof brackets, although they still have four holes and seem to need them. The extra two screws aren't included (used my own). Both the written instructions and video are oddly vague on exactly where the reinforcing bar goes on the underside of the roof as well. No pre-drilled holes or even indents, so I sort of centered it between two similar-looking bumps. Agree with others that the hinge screws are tricky to install given the hinge doesn't open far enough to really get a screwdriver in there and alignment is apparently just "however you can make it work." A powered driver with a longish-bit helped. Despite these clunky issues with the assembly and instructions, this is a good product. Feels solid, looks good, and the Suncast shed my Dad has had for 15 years still looks great.
Guys i figured it out. Put all sides in starting from back left. The sides where the corners connect line up and rubber mallet into place starting from the bottom. They dont slide in like they look like they are made to do. You just hammer them into each other with rubber mallet.
I just got a Suncast BNS5700 Shed via Home Depot. I carefully followed the poorly written instructions and have found some issues: 1. Parts #s of left and right panels do not match the #s in the instructions; 2. Quality is not as good as expected or it’s just overpriced for its quality. The plastic parts got bent after placing them at 75 degree F under sunlight for about an hour; 3. The metal support is hard to be installed on the roof because the pre-drilled holes are too small for the 6 screws to screw in. If you follow the written instructions to install it without watching this video, you may get confused with some steps. Not recommended!
On all these videos for putting this together it is not showing the bottom of the back panels that are like mine. The tabs are different on mine. I can't figure out how to slide the sides on and the bottom to slide in place similar to he sides.
Thank you so much for this video I am 72 years old and put this thing together by myself. I could have never done it if not for this video again thank you so very much😊
Thank you for this video. It helped me finish assembling our Suncast shed. Very helpful!
This video helped out sooo much! Thanks! Between the instructions and this video assembly was no problem. ❤
Just got the shed, yesterday and assembled it today, found the instructions simple and easy to follow, but for the hinges, took a bit to figure out which side is up, five minutes of playing around sorted it out nicely. Would appreciate some hints re fasteners to the base, either concrete or wood. All in all took about an hour to assemble.
Very helpful, especially given the written instructions are a bit wonky. At one point, it orders you to put a washer and bolt going in both directions in the same hole (?!). This clarifies the intent was just to put a washer on each side. The written instructions also say to put just two screws in the roof brackets, although they still have four holes and seem to need them. The extra two screws aren't included (used my own). Both the written instructions and video are oddly vague on exactly where the reinforcing bar goes on the underside of the roof as well. No pre-drilled holes or even indents, so I sort of centered it between two similar-looking bumps. Agree with others that the hinge screws are tricky to install given the hinge doesn't open far enough to really get a screwdriver in there and alignment is apparently just "however you can make it work." A powered driver with a longish-bit helped.
Despite these clunky issues with the assembly and instructions, this is a good product. Feels solid, looks good, and the Suncast shed my Dad has had for 15 years still looks great.
Guys i figured it out. Put all sides in starting from back left. The sides where the corners connect line up and rubber mallet into place starting from the bottom. They dont slide in like they look like they are made to do. You just hammer them into each other with rubber mallet.
I just got a Suncast BNS5700 Shed via Home Depot. I carefully followed the poorly written instructions and have found some issues: 1. Parts #s of left and right panels do not match the #s in the instructions; 2. Quality is not as good as expected or it’s just overpriced for its quality. The plastic parts got bent after placing them at 75 degree F under sunlight for about an hour; 3. The metal support is hard to be installed on the roof because the pre-drilled holes are too small for the 6 screws to screw in. If you follow the written instructions to install it without watching this video, you may get confused with some steps. Not recommended!
On all these videos for putting this together it is not showing the bottom of the back panels that are like mine. The tabs are different on mine. I can't figure out how to slide the sides on and the bottom to slide in place similar to he sides.
Same. There is no way to slide in the side pieces without warping the bottom or the sides.
This is the exact issue I’m having now. It doesn’t just snap in like they show. What the crud.
Can’t get panel c in bottom slot. Three days now.
The doors are a pain to install but otherwise a great shed
Seriously?
Can you do it simple?
IKEA is example
Good luck people!
Put screws to hinge is a really pain in the ass. Wall panel doesn't fit to the side panel. Idea for this product is simple, but sadly quality is not.
Not Ble to install the hinges to the door