Kitchenaid Mixer Plastic Worm Gear Replacement! Mixer Not Spinning.
Вставка
- Опубліковано 1 лис 2020
- In this video, we dive into one of the most common issues that mixers face. When under a heavy load the worm gear strips leaving the mixer useless. Fix it cheap! Parts and grease available on our website! Make sure to replace the grease and gasket while inside!
----------------------------------------------------------------------------------------------------
Mr. Mixer store: www.mrmixer.store/
Discord server: / discord
Facebook: / mrmixer316
TikTok: www.tiktok.com/@mr._mixer?lan...
Instagram: / mr._mixer_
![Lp. Последняя Реальность #107 РОДНОЙ ДОМ [Финал] • Майнкрафт](http://i.ytimg.com/vi/IK3QKzKUlHM/mqdefault.jpg)
Boom! Amazon + your video, Money saved. Easy fix. Bravo!
Nooo!! If you buy an Amazon gear it will fail! The gear is going to start spinning around the bearing and slipping so it won't mix properly. Consider picking one up from our website. You'll notice the issue the first couple times you use it.
until this video, I wasn't aware that the PROPER gear material was Kevlar and that the "cheap knock-offs" did not have either that same material and/or had an inferior method of how the hub attached to the plastic portion. In viewing other viewers' comments i can see that they learned the hard way about the difference! You have very useful videos addressing typical repair/maintenance issues for these mixers.
I appreciate you
Received the replacement gear and grease today. The videos were perfect for replacing both. Thank you so much for such simple clear directions.
Dude!! Thank you for making this vid! I watched 3 vids before I found yours and I would have saved so much hassle if I’d watched yours first. Thank you!!!
Thanks for the break down info. Very nice. Those mixers are surprisingly built very well.
They really are!
Thanks for the video, I replaced gear successfully. Machine working perfectly.
Congratz! 🙌
Bought an Amazon worm gear and my mixer appeared to work until it was put under load. I Replaced that gear with one of your factory gears and it works great now. Thanks for the videos!
Happy to help
Wish I had watched your videos last year when i replaced with an Amazon gear. Here I am doing the job again, this time, I bought from you, great videos!
😢 It's a shame that they are even able to sell those. It's such a joke. I'm glad I could help
You make it look so easy the pin won't come out !!
Mr. Mixer is right! I bought a cheap worm gear replacement on ebay some weeks ago together with two replacement motor carbon brushes. The gear failed on the first run - 100% waste of money. If you buy cheap, you buy twice! Thanks fpr the nice video. Greetings from Germany :-)
Hello! Thanks for watching glad to help!
Same here bought a cheap worm gear. Claimed to be stronger than oem! It spins but won't turn even cookie dough!
Awesome thanks so much, saved the day!
Nice! Finally I got solution from this video, thank you so much
My pleasure!
Thank you!!!!! This was so detailed I felt I could do it….and did it!!
Love to hear it! Its my pleasure!
Wish I would have watched this video before buying cheap replacement on Amazon. Immediately broke. Good video!
It's so unfortunate that they are even able to sell those!! Happy to help
Mr Mixer and team are doing god's work here.
I appreciate you
I bought "that" gear. Now I'm paying for it twice! didn't even get through one batch of cookies. Bought a factory one from you and now I'm watching your video to install it!
Sorry I wish I could have warned you sooner!
Thank you so much.
You are very welcome!
Thanks
Spectacular tutorial! Very educational for my current situation. Now let me educate you on proper gear names…
What you are replacing is properly called a helical gear, designed to be quieter in car transmissions and great forrr…. Worm gear driven applications. The long screw like gear driving your Kevlar helical? THAT is your worm gear.
omg I laughed so hard when you opened that desk drawer. so relatable.
😅 Watching these old videos brings back some memories! My shop has changed drastically since then!
Great info. Thanks
Hi, thank you for this video! Can you please tell me how to remove the planetaire with that punch? Cause when I use the punch I cannot take the pen out. It is stocked into the machine. I do not dare to slam so hard with my hammer. Do you have an advise for me?
Thank you so much for this video! Would you recommend doing this if my mixer gets warm and struggles/stops spinning when mixing heavy things like bread doughs?
I would recommend regreasing your machine, it will help quite a bit!
I opened mine up and expected to find busted gears, but all looked ok! The mixer is 13 years old and a few months ago it stopped working very well under loads and the orbital would not turn well. Should I regrease and try again?
Carefully tapping the pin in but it's bending toward the gear. I'm going to keep trying but have my doubts. Very tight, and this is a vintage Hobart lift bowl model.
damn, did not realize the worm gear was made of kevlar, that is way stronger then some plastic aftermarket one.
Now, this is for the tilt head. But what about the lift bowl? I have the professional 6 and need to replace mine. Help!
I have enjoyed following along with the video. I have my machine half way apart.
My mixer does not tilt back, but the bowl holding arm raises and lowers. I have follow up to the point of removing the screws that hold the top cover on near the planetary but I do not see screws in the back. I got the plug wire freed from where it was but now I am stuck. I don't have two screws in the back and the top cover seems quite secure.
Do you have any advice for me?
Thank you very much.
I think this is the video series you'll want to watch! ua-cam.com/video/20-UJD_asKA/v-deo.html
good video i want to ask if what to do if the machine will run for a second and will stop thankyou
Does the motor completely stop or does it keep running but the beater shaft stops? Which model of machine?
14:00 What would cause the worm gear pin to be loose, and how to fix it? It slides all the way through with no resistance. It was tight enough when I punched it out...
Great video cheers, don't suppose you or anyone else has heard of people buying good quality gears from the uk? the amazon ones look cheap and my wife relies on the mixer for her business. thanks again.
I'm not sure where to get them in the UK, we ship there but shipping is 20$, do not buy Amazon the gears fail immediately and you will have to take it apart and swap it again.
I... Um... Got the pin from the worm gear housing stuck in the backside, punched it towards the back wall rather than out of the side. What do I do now?
I repaired my mixer a year ago and replaced the worm gear. But now the accessory head will not turn the accessories. I can't find any video that addresses this issue. I NEED my juicer and meat grinder to work!!!!! no accessories work. They "turn" but any resistence makes them stop. Help.
After replacing the worm gear my mixer is hesitating and won’t spin though anything denser than water, what can I do
Thanks for the video, though I had a question, I bought a worm gear (before seeing your video) the description says it is an OEM part (and it came in a "whirlpool factory certified part" bag) but the gears are black (instead of yellow) do you know if they changed colors recently? The part states it was manufactured in 2021 and doesn't spin freely.
Yes they switched to black about a year ago, however it should free spin. Did you buy the whole tower or just the gear?
@@MrMixer316 thanks for that conformation. I was just talking about the worm gear not the whole tower. I gear itself doesn't spin free on the bearings (like you showed it shouldn't in the video) so I assumed it was genuine OEM but the color was concerning me. Thanks for making me feel better before making the repair, love the videos they are very informative
I have a KitchenAid Artisan Stand Mixer KSM150, which is about 5 years old. Recently it had some big noises and thus I changed the worm gear as well as grease. Now it can spin quietly without anything in the bowl, but when it is making a dough with a flat beater it occasionally gets stuck and stops spinning (motor still sounds running) until it slowly gets over it. It looks as if it is not powerful enough or the torque is not large enough. Do you have any idea what might cause this problem? Thank you
The gear you used was not a factory replacement it's slipping on its bearing. Get a factory worm gear
My mixer is making a loud whining noise and grinding a bit under heavy loads, I’ve also noticed inconsistent orbital speed at higher settings. Could this be an issue with the worm gear? Thanks for the great videos and advice!
It could be, but more likely an issue with the phase board/speed plate or governor
Hi where can i find the squarehead bit in your store?
www.mrmixer.store/store-2den3/p/hx6n06ypknh0f3u3wjqkfystf9lorq
After changing the worm gear my kitchenaid makes an infernal noise. Any suggestions? I regreased everything. But the clicking sort of electrical noise is awful. Any help will be appreciated. Thanks
Send me a video please
Followed everything. Putting together became easy. Turned it on, rotated and stopped. Took it apart, rotated the large gear, it get almost full circle and stop. Reverse the other way, gets to that exact point and stops. What happened?
I opened mine up and the worm gear looks fine but the pinion gear it wrecked to the point that the grease was silver. Is this common? I'm going to order the part if I can in Canada but I'm worried if I don't know what caused it it will just happen again.
I think just replacing it is fine! You'll need grease, a gasket and the pinion shaft gear is what it's called. Ive seen it a few times
I went to your site to get a worm gear, but the link above is just a general one, and I couldn’t find a worm gear in the section for 5 qt lift mixers
Here you go! www.mrmixer.store/store/p/5qx3tt8knkavd73vvwc7ms5z2jjreb
Removing the pin is extremely difficult, especially with the whole part rotating. Wish you slowed this down and showed how you did it close up. Your insteuctions are great, but this prpcess took me several hours in reality. Things dont come apart easily at all.
Is it possible to show how to replace the center gear of an Artisan 5KSM175? Thanks in advance :-)
Watch the regrease series all you would need is a new gear the assembly is the same!
@@MrMixer316 I thought about everything, but not that easy. I'm sorry LOL. Thanks very much!!!!
@@angelikathiele8351 it's an easy process you got it no problem!
@@MrMixer316 Thanks!!!
Thanks for the video! I watched a couple and yours helped the most! I have the KSM 125 Artisan. Do you ship the worm gear to Singapore? And what is that thing which is used to remove the pins , going to get them. any specific sizes? Dm if need to! Daniel
im not sure if we have singapore opened up, shipping out of the country is 20$, i would recommend grease and gasket as well! i can open up singapore on our website if you would like to order!
@@MrMixer316 do you sell the whole worm gear set? part wp240309-2 i think
About to replace a Worm gear on my machine, looking to buy the parts but am in Canada and dont want to get a cheapo part, any suggestions on reputable parts suppliers in Canada?
I'm not sure honestly! We do offer them but we charge 20 dollars for shipping out of the country
is there any store online where i can buy original gear? im from philippines
I'm not sure if we have the Phillipines open for shipping but our online store is Mrmixer.store
hey,thanks for posting these helpful videos. i am stuck at removing the pin . looks the pin is stuck completely. how do i proceed?
Two option hit it harder with a bigger hammer, or any little machine shop will punch it out for you or drill it if necessary.
@@MrMixer316 ok
I try it
@@MrMixer316 not happening
ok mine has 5 square screws but they are really small and i can't get to open them. what should i use please
@@umeramirza3173 it's an S1 square bit we have them in our store
I don't have tick toc and am so glad a friend sent this to me.. Do you have a video on general maintenance? i know now I am goingto go grab my small one from storage and see about fixing it now.!! I love my kitchen aids! Oh and will you be selling parts?? Can I "Wash" my parts clean and replace with all new grease?
I'm glad they did too! Happy to have you here! I'm working to get a full line of videos out for every issue and aspect of the mixer. I offer parts and grease on my website in the description!
I am stuck. The pin from the worm gear housing will not come out. I can punch it back and forth a millimeter from one side to the other but that's it. How do I get it out?
Hit it harder, worst case scenario replace the whole worm gear assembly! We offer them on our website it comes as the whole tower complete with gears
Can't seem to find worm gear for model KSM150PSMC.
Here is a link to our website www.mrmixer.store/store-2DeN3/p/5qx3tt8knkavd73vvwc7ms5z2jjreb
@@MrMixer316 Thank you so much. Your video was very helpful. I put my order in Just now!
Are the gears the same? how to buy the one that fits my KitchenAid model?
All of the tilt head models use the same gears
It's referred to as the factory replacement worm gear on our website
I’m looking and I can’t see any damage to the worm gear. Is there something else it could be?
It could be the worm gear/center gear or it could be sheared pins
@@MrMixer316 yeah, the pin is gone lol
@@stephengalindo6340 whoops!
Hello guys I am new here.my name is Adrian and I am from Romania. I have a Kitchenaid mixer with the warm gear damaged. My question is if thisbwas original or fake ( it was black color ). How should I reconise this .
The black is normal, they can be yellow or black as the kitchenaid company originally made them black then it switched to yellow then back to black!
@@MrMixer316 Thank you very much for the information. I still have a last question: is the grinder accessory destroying the warm gear? I have the classic model but as I understood from you the warm gear is same for Artisan also. thank you.
@@adriananghel-vn7jb the worm gear will naturally wear over time and grinding shouldn't damage it unless youre meat is frozen soild or room temp. It's best to grind with the meat being really cold, almost firm to the touch
Wish me luck!
You got this!!
I did it! Thanks to your video I was able to swap that gear out and grease it up in no time.
@@nickhaney4882 you rock, so glad we could help!
Wear am I Supposed to buy the gear then
We carry them! www.mrmixer.store/store/p/5qx3tt8knkavd73vvwc7ms5z2jjreb?rq=Factory
Where can I get a good worm gear?
From our website Mrmixer.store
@@MrMixer316 Okay will look. Can you do a vid on repalcing the worm gear on a cuisinart M-50 Or do you know where I can find that vid? It's a little different than the kitchenaid Thanks
@@MrMixer316 Which on of your worm gears will work on the cuisinart M-50? Thanks
@@inthehouse9062 sorry we only carry parts for the kitchenaid mixers
@@MrMixer316 But the worm gear is the same right?
Do I need a special WORM gear for model #KG25H0XAQ
This is the gear you will lost likely need. Watch our professional 600 regrease tutorial for the how to! www.mrmixer.store/store-2den3/p/yhnwsrjcxcw0t2oaigs2ylh89p9pqi-f49w3
Can I ask you something?
Certainly
@Roman N haha hey it happens to me all the time, there one minute gone the next, thank heavens for adhd am I right?? 😭
Mister mixer is very secsi. Mr mixer should marry me so we can be Mr and Dr. Mixer
@@user-vn7ky2xr1x 😉
@@MrMixer316 Dr. Mixer, MD. Double board certified in internal medicine and critical care and Pulmonology. I like the sound of it.
The problem with the 5 quart mixers is they put in a Nylon aka plastic gear which wears out. That is one reason I payed $50 more and got the 6 quart model with a heavier motor. I like metal gears which last longer . Also easier to work on. I say better built as well.