@NubsWithGuns You'll find it's a poorly designed engine. Kohler had an opposed twin before B&S did & it used a gear driven pump. Use a B&S twin on slopes & hillsides & see what you'll get. As for the 1st part of your reply I fully agree.
@@darrellepickering8433 I have a ~30* hill that tips the engine toward the right side. I've had it like that 8 years without problems. Only here because the engine is ~25 years old and could probably do with a rebuild.
@SalientDebate verticle or horizontal motor? Verticles had a slinger, horizontals only had a single dipper & it was only on 1 rod. If those were used on slopes with much of an angle whether it be side to side or up/down oil starvation could happen.
Hello, thank you for your video. I am just getting into small engines. I’ve never known anything about them till I came upon a used non working mini bike I got for my son. Luckily it just needed a carb clean, but got me hooked on small motors. I recently found an old opposing valve 18 hp Briggs that was thrown away and then found your video. The project will be a step up from the predators I’ve been messing with but I want to see that big motor running again. Where did you find the replacement stuff, and how much did the new parts cost?
I got the parts from eBay the parts cost about $150 for the all the parts I got for this engine but you can get a full rebuild kit for it now that comes with everything including the valves and pistons for about $225 I think. Thanks for watching
22:53 Can I flush that out with Kerosene where the valve stems are without having to take any other parts off (besides the carb and air intake manifold)? Where would that drain out to? (I have dirty rain water/mud in that section) Would you suggest me taking the cylinder head cover off and flush it through the valve openings while hand spinning the engine? Thanks. I've fixed/replaced everything else on my rebuild and only have this problem left. I appreciate the video and your time! Thank you.
Yes I would suggest taking the cylinder heads off and flush it through the the valve openings and if you don't take the heads off it should drain into the crankcase so I would also suggest changing the oil when you are done
I am currently working on an 18hp opposed twin engine. Do these engines have a compression release in them? I haven't found any indication anywhere that they do. Thanks for your kind answer. I have installed dual carburetors along with the dual exhaust on mine, but have been having issues with exhaust coming back through the carburetors. I am in process of adjusting the valves right now and have found that they are way out of adjustment.
Could you possibly send me some picture of all the carb linkage I rebuilded the engine but I cant remember the linkage hookup PLEASE AND THANK YOU i ORDERED A CARB FROM BRIGGS AND IT'S A LITTLE DIFF FROM MY OLD ONE
Thank you. because for your video I have found the correct parts to fix my 1984 brigs & Stratton twin 18hp
Good that you’re rebuilding it before it blows up, it’s surly worth saving
im a bit late to the party (so to speak lol..i just found your channel)) i see you rockin the us general rolli8ng cart pretty cool....
Those were essentially 2 11 hp B&S mated. Had a very poor oiling system (dipper). Don't run those over 15° from level. Done a few of those.
@NubsWithGuns You'll find it's a poorly designed engine. Kohler had an opposed twin before B&S did & it used a gear driven pump. Use a B&S twin on slopes & hillsides & see what you'll get. As for the 1st part of your reply I fully agree.
@@darrellepickering8433 I have a ~30* hill that tips the engine toward the right side. I've had it like that 8 years without problems. Only here because the engine is ~25 years old and could probably do with a rebuild.
@SalientDebate verticle or horizontal motor? Verticles had a slinger, horizontals only had a single dipper & it was only on 1 rod. If those were used on slopes with much of an angle whether it be side to side or up/down oil starvation could happen.
Flat land engine for sure 😊
Hello, thank you for your video. I am just getting into small engines. I’ve never known anything about them till I came upon a used non working mini bike I got for my son. Luckily it just needed a carb clean, but got me hooked on small motors. I recently found an old opposing valve 18 hp Briggs that was thrown away and then found your video. The project will be a step up from the predators I’ve been messing with but I want to see that big motor running again. Where did you find the replacement stuff, and how much did the new parts cost?
I got the parts from eBay the parts cost about $150 for the all the parts I got for this engine but you can get a full rebuild kit for it now that comes with everything including the valves and pistons for about $225 I think. Thanks for watching
22:53 Can I flush that out with Kerosene where the valve stems are without having to take any other parts off (besides the carb and air intake manifold)? Where would that drain out to? (I have dirty rain water/mud in that section) Would you suggest me taking the cylinder head cover off and flush it through the valve openings while hand spinning the engine? Thanks.
I've fixed/replaced everything else on my rebuild and only have this problem left. I appreciate the video and your time! Thank you.
Yes I would suggest taking the cylinder heads off and flush it through the the valve openings and if you don't take the heads off it should drain into the crankcase so I would also suggest changing the oil when you are done
@@rescuerestorerepeat8500 Thank you!
Where would you find the points Gap the ignition Gap spark plug gap is there a source
You should be able to Google it and check but it should be .020 on the points and .025 for the spark plug gap
What year did they go with new style Rods? Looking at buying a 1997 engine.
I think the new style rods started in 1990 so 1997 should have them
Need your help! I have the same 422437 18 HP. Needs rebuild. Can't seem to find piston rings. Where did you get yours from? Thanks!!
I am currently working on an 18hp opposed twin engine. Do these engines have a compression release in them? I haven't found any indication anywhere that they do. Thanks for your kind answer. I have installed dual carburetors along with the dual exhaust on mine, but have been having issues with exhaust coming back through the carburetors. I am in process of adjusting the valves right now and have found that they are way out of adjustment.
These engines don't have a compression release in them. by the way how did you setup the dual carburetors?
Could you possibly send me some picture of all the carb linkage I rebuilded the engine but I cant remember the linkage hookup PLEASE AND THANK YOU i ORDERED A CARB FROM BRIGGS AND IT'S A LITTLE DIFF FROM MY OLD ONE
How can I send the picture? I can't put it in the comments
Where did you get your parts@@rescuerestorerepeat8500
Could you show me governor Springs location on these motors
Is that just a straight pipe or do you have mufflers in-between
Just a straight pipe no mufflers