RODE MOJ, ŽELIM TEBI I SVIMA BOŽJI BLAGOSLOV. TRAŽIO SAM DA VIDIM KAKO NAPRAVITI JEDNOSTAVNI, ALI DOBRU NAPRAVU ZA SAVIJANJE LIMA. EVO SADA SAM VIDIO TAKVU NAPRAVU SAGRAĐENU JEDNOSTAVNO ALI JAKO DOBRO. LIJEPO JE SVE PRIKAZANO SA PUNO UMJEŠNOSTI I LJUBAVI PREMA POSLU. TO ME RADUJE . ZAHVALAN SAM ZA IDEJU. ŽELIM PUNO USPJEHA U ŽIVOTU I RADU TEBI TVOJOJ OBITELJI I SVIMA.
Thanks for posting this. I just started making this now with a few changes. You have a 2 piece hinge, I’m using a 3 piece hinge. The center pin will be removable so I can separate the 2 angle iron pieces. The top clamp part that is held down with bolts I’ll be milling the leading edge so it’s flush with the metal that’s being bent so I can get a sharp angle at the bend, not a rounded one.
Weld a washer or metal plate on top clamp bar under where screw down is. Makes for better clampdown. Have made many benders like this in past..Plus weld some spinner handles so dont need an allen key to tighten it up
Very cool. I'd like to make one with one important difference: make the hinge not in line with the bend. I often have to clad the exteriors of windows with sheet metal and the metal is often 1.5 meters or more. The length of your bender is perfect for portability, but if I could slide longer pieces through and make the bend gradually, that would be brilliant. I currently use a little hand bender and it takes forever.
I think the piece which sits on top eith the springs is wrong. It does not provide a bemding point at all. But you could just grind it flat (45 degrees) so it sit flush. That would be a huge improvement.
So your one can make hotdog and hamburger holders, perfect for barbeques, hotdog stands and burger vans if you make them from stainless steel. Great stuff, thankyou for sharing.
RODE MOJ, ŽELIM TEBI I SVIMA BOŽJI BLAGOSLOV.
TRAŽIO SAM DA VIDIM KAKO NAPRAVITI JEDNOSTAVNI, ALI DOBRU NAPRAVU ZA SAVIJANJE LIMA. EVO SADA SAM VIDIO TAKVU NAPRAVU SAGRAĐENU JEDNOSTAVNO ALI JAKO DOBRO. LIJEPO JE SVE PRIKAZANO SA PUNO UMJEŠNOSTI I LJUBAVI PREMA POSLU. TO ME RADUJE . ZAHVALAN SAM ZA IDEJU. ŽELIM PUNO USPJEHA U ŽIVOTU I RADU TEBI TVOJOJ OBITELJI I SVIMA.
Thanks for posting this. I just started making this now with a few changes. You have a 2 piece hinge, I’m using a 3 piece hinge. The center pin will be removable so I can separate the 2 angle iron pieces.
The top clamp part that is held down with bolts I’ll be milling the leading edge so it’s flush with the metal that’s being bent so I can get a sharp angle at the bend, not a rounded one.
Very cool. Well done 👍👍
EXCELLENT JOB. THANKS FOR SHARING.
Nice work. You don't need a lot of stuff to make what you need. A center punch made out of an old threading tap👍👍.
Muy sencillo, bien explicado y sin complicaciones inecesarias...
Gracias
Weld a washer or metal plate on top clamp bar under where screw down is. Makes for better clampdown. Have made many benders like this in past..Plus weld some spinner handles so dont need an allen key to tighten it up
Weld a small rod over the hex bolts to make them wing nuts ,easier than using an allen key
Congratulations! The best idea. Easy to make, functional and small to storage.
Muy bueno su invento
Napakagandang gayahin kaibigan. Thanks of your efforts. 👍🇵🇭
Ayos master, bagonh kaibigan...
¡Buenísimo diseño! ¡gracias por compartir!
Excelente felicitaciones Maestro Venezuela gracias saludos cordiales
Gracias!!!
Muy útil y muy bien presentado
world need more of this
Super basic… Beautiful!
Nice job,mate.
👍👍👍👍👍👍🙂 Excellent job. This is why I ❤ UA-cam.
Excellent job! Like and inscription..... Your friend from Brasil!!!
Very very good n best
Good job bro 💐
Good work!
Gracias por la explicación 👍 saludos desde cali
Buen trabajo...FELICIDADES !!!!
This is just brilliant. Simply the best.
FERRAMENTA MUITO BOA. PARABÉNS
good project
can you please name for me the hinges used here?
Tom
За простоту огромный плюс, а вот прижим надо делать тщательнее - угол изгиба получается не очень, радиус большой
Good work
great job, now i know what to do, to bend my metalsheet ;-)
Simplesmente perfeito! Parabéns!!!!!!
Thank you for your video. 👍
Muy bueno , sencillo y con poco material. 3 Angulos, uno más pequeño y dos perfiles cuadrados con dos bisagras de soldar
Excelente video buen trabajo felicidades 🍾🎈🎉🎊🍺🍻🍺🍻🍺🍻🍺🍻🍺🍻🍺🍻🍺🍻🍺🍻🍻🍻🍻
Very cool. I'd like to make one with one important difference: make the hinge not in line with the bend. I often have to clad the exteriors of windows with sheet metal and the metal is often 1.5 meters or more. The length of your bender is perfect for portability, but if I could slide longer pieces through and make the bend gradually, that would be brilliant. I currently use a little hand bender and it takes forever.
Well, there's still the issue of the clamp - I'm going to have to think this through some more.
Make it longer than, your hinges have to be in that spot or you'll end up with a pivot point that creates a gap and a bad bend
Exelente idea
Nice job
It was very good congratulations
WoW! Now, this is something I can make and use in the metal shop. Great idea!
Top mano
lost me when the welder came out . Most of us diy'ers do not have all the equipment we need . Nice video and product.
If you don't have a welder its unlikely you will need this tool.
@@Carsnbikes73 Ahhh but not everything bent gets welded.
Use bolt-on hinges and screws
Very good, thanks.
Superbe vidéo
The sheet you bend which millimeter?
Simple the best. I have to make a similar bender. Thanks for the idea.
Your metal bend in the end, very strange in deed.
That was great well done bro👍👍👍
Muy bien carnal, la voy a fabricar gracias y saludos .
Wow nic trik
Bardzo dobra robota Pozdrowienia z Polski
Great work.
👍👍👍👍👍👍🙂 Excellent.
U r superb bro
Really Works Your DIY Bending Plate Ideas. Like it 👍 #creativefeature
Boa, vou fazer uma igual.
Nicely done! Thank you for sharing.
I think the piece which sits on top eith the springs is wrong. It does not provide a bemding point at all. But you could just grind it flat (45 degrees) so it sit flush. That would be a huge improvement.
So your one can make hotdog and hamburger holders, perfect for barbeques, hotdog stands and burger vans if you make them from stainless steel.
Great stuff, thankyou for sharing.
Dommage qu'on ne donne pas les dimensions des Gonds et hauteur ?
good job my brother
Excelente .
Brilliant idea
Nice work!
me gusto facil de hacer y buena herramienta
Good job
Very good video, very good job sure do like it think I will have o make me one.
Genial. Gracias!!
Legal hein!!!
Very nice,
Ingenioso y sencillo . Está bien la idea. saludos.
Can it bend 2mm metal sheet?
Fantastic
Congratulations!!
without a doubt
Excelente, censillo y práctico 👍
Dikit na dikit sayo.
Parabéns.....simples é eficaz
Great...
Com esse equipamento consigo dobrar chapa de 3.5 milímetros???
So simple, yet effective, nice one 👍👍
Mantap Bang
merci c'est simple à réaliser !
Excelente trabajo muy bueno.
احسنت،يامعلم
Nice
Mini bending machine is quite handy
Clever!
Thank yu ...EXCELENT
Nice selfmade Tool 👌
Vou já fazer isso AGORA 🕵️
I think I can make one like this..
what size are the bolts you used?
Très bon
Well by golly dat waz awesome
When you welded the bullet hinges you had paper or tape wedged in under the hinge 🤷♂️ was there a reason for this? I’m making one now
clearance so the hinge doesn't bind, I've watched a few videos to get an idea and watched a video of how to install the hinge.
Gostei do vídeo.
Muy bueno
Nota 10 viu parabéns
Buen video
Amazing!!! Thank you! 💪
Klasse ❤