Owner has decided to use the BRT Gas Tube to correct the oversize Gas Port. All of the parts to make this gun run right will cost about $250. -JP Titanium Firing Pin -Colt FPRP -Colt Receiver End Plate -Sprinco Gas Rings -Sprinco Ejector Spring -Sprinco 5 Coil Extractor Spring -Sprinco Blue Buffer Spring -Sprinco Hammer Spring -SOTAR Carrier Key -SOTAR Spirol Pin Kit -OCKS Carrier Key Screws -BCM Gas Block -BRT Gas Tube
Thanks Chad. It's interesting how many of those parts you've used, or mentioned, in prior diagnosis and repair videos. Almost as if you know which parts can often be sub-par, and what aftermarket items are best used as replacements! 😉 That shortened buffer spring -- that suggests it was too short to begin, rather than something has compressed it over time, doesn't it? You knew there would be score marks from the BCG striking the lower at the extension tube! This autopsy being so comprehensive, it's almost like a perfect cadaver for teaching the common failure/flaw points. Thanks as always.
@@seanoneil277 I believe the spring was short for 2 reasons. 1) because it had some use (some cheaper springs can go bad in a few thousand rounds), and 2) it's a cheap spring. Based off of the bore scope (done after the video), the barrel has at least 500 to possibly a couple thousand rounds. It's seen some use, nothing significant though.
@@SchooloftheAmericanRifle Thank you. I shouldn't be surprised that some assemblers would use a substandard spring, after seeing substandard quality in other parts in your prior videos. Every time I watch one of these autopsies I'm grateful for all that I learned from your SOTAR videos before I assembled my first one. Your SOTAR video library is the next best thing to taking your class, and I took full advantage of the library. These autopsies now feel like confirmation of what I learned from your videos, and how that informed my part choices. Happy 4th to you and your family, Chad. Thanks.
To me, the most interesting aspect of this autopsy is how the leaky gas block, loose gas key, and inefficient bolt carrier partially “correct” that gaping gas port. By putting a known-good BCG in the gun, you demonstrated that it wouldn’t run right even with a heavy spring and heavy buffer. This emphasized how the entire system must interact correctly. You also demonstrated how you can chase your own tail unless you understand WHY the gun isn’t running right in the first place. Thanks!
I like to think of it as a 1-cylinder version of a car engine. If you had a leak in your intake system (carb/manifold interface, manifold/head interface, or along the manifold runs) your engine would be wheezy at best and maybe wouldn't start or stay running if it sparked over. In the AR the gas drives the engine and it needs to be metered properly for all the parts to be happy working together. Otherwise you have a fancy overcomplex bolt gun, with parts meant to work a bit unlike a bolt gun does. Someone up above in a stand-alone comment mentioned the overgassed nature of the huge gas port was offset by the leakage at the wobbly gas key. Either alone would have been a fairly straightforward Dx but together they offset each other and made Dx confounding. Add in the buffer and buffer spring weakness and that's a lawn mower that won't start or won't stay running when it does.
heh, I was thinking the same thing right before I read your comment. Interesting how the combo of over-gassed, loose gas block and carrier key is a trifecta of problems that kinda sorta cancel each other out a little. At least it kept the gun limping along for a little while.
Thank you to both of you for doing these. The quality of the content in just production, when the purpose is not to make money, says a lot about both of you; but that the information in these videos is of such a high quality and the result of such investment, and that we can all take advantage of that, thank you very much indeed.
I think the most refreshing thing for me, from this video, was the appreciation for your diplomacy. Most YT gun personalities would have just trashed the maker. You listed your observations , judgement free. That must have been a challenge, so bravo. Happy 4th.
I really enjoy how thorough you are with your examinations and the detail you go into when describing the issues as you come across them. I always learn something with every one of your videos, and I thank you for that! Cheers
She does. Sometimes I forget someone else is running the camera because she's always focused on what Chad is talking about. I noticed when Chad was listing all the things wrong and was forgetting something, she would focus on that to give him a hint.
My great appreciation for your expert tutelage. For those willing to learn, the knowledge you present is like food to a starving man. As I continue my journey through custom building and problem diagnostics, your videos serve as my classroom. I have learned a lot about how the gas/BCG/buffer systems work together, but this video just took me up another notch. Friend, you can consider me an apprentice. Thanks again.
I'm in the middle of building my first AR-15 with a 3D printed lower receiver and a freedom rifle kit from Palmetto State Armory... videos like this have been super helpful to carry me through, thanks for making!
Wouldn’t bother with the 3D printed lower, longest me and the boys have ever been able to get one to run is about 500 rounds. Past that point, they break at the receiver extension. Just buy a lower off palmetto, they’re like $160. The government knows where you live and what you buy anyway.
@spacecaesar7619 yeah but 3d print design account for failure points. The orca AR15 has a 3d printed upper and a lower, those rifles can run thousands of rounds.
Impressed that you dont cut away and edit out the little errors. Continuous video says it all when it comes to trusting that someone truly knows what theyre doing.
Probably the best video I have ever seen when it comes to trouble shooting an AR, perfectly demonstrates that without the knowledge of how the gas system works and needs to be balanced, you could chase problems on this rifle in a circle. You fix one issue that exacerbates another because how off the balance of the rifle was, I could see this rifle driving someone crazy.
This is so inspiring... I do work on and fab minor parts for my firearms, but I am a general machinist, not a gunsmith. Watching the methods is inspiring, and watching the knowledge/experience involved is humbling. I will continue to apply what I learn from this channel on my existing LR-308's and AR-15 type rifles. I can't wait to compare Colt to Windham to PSA. Thank you for sharing so much knowledge, experience, and wisdom.
Hey I was at a gun show and they had a booth . I liked the way the Plankton Ranger looked and handled but something told me no . I'm 62 so here is a life lessson ,"Never Impulse buy. Thanks for the video 😎
Chad, thank you & the Mrs’s so much for another highly informative video! Always love learning more & greatly appreciate the lessons!So excited these videos are back!
This is one of your best vids so far! It takes a failure like this to fully understand how all the parts work together and what is required for proper function. Everything clicked when you gauged the gas port...I immediately visualized the entire pathology of the rifle.
I lived in Neosho, MO and bought my first AR barrel, a Black Rain. I was hoping for sub MOA accuracy out of it, but it was more like 2 MOA, so I did not buy any more of their products...good thing. Thanks for doing what you do!
I gotta say, as a former Naval Architect/Mechanical Engineer who used to work closely with machinists, what you do is exhibit A for why machinists and folks like them are so darn important. Sure, engineers can design something, set tolerances, do fatigue analysis, etc., but if you don't run your design by a machinist or someone who has your type of niche expertise, you more than likely will screw something up. I know because I've done it, to the tune of more money that I will ever admit. All the training and education in the world doesn't compare to hands on no BS experience and the "been there done that" aspect of things. Thanks for sharing this stuff. Now excuse me as I go on to do another AR-15 build with a Nitride BCG!
Learned a lot about AR’s from this video. First how good the guy is that has built all of my AR’s. Never had any of these problems and they all shoot great, at half price of this gun. Plus maybe its more important to spend more time on quality control that on laser engraving the logo on every possible piece of the gun. Thanks for the video.
Thank-you Chad!!! I often “watch” your videos by letting them run in the background (on the TV) while I work on something else. Not this time though! This video helped me identify a problem that I didn’t know I had, and address it BEFORE damage had occurred. When I switched to a Magpul PRS stock on the 3-Gun rifle I use for long-range stages, I grabbed my longest spring and longest buffer out of my parts bin. It was supposedly an “easy” change over… didn’t know my BCG was traveling too far into the extension and the gas key was hitting the receiver. Thanks for the “quarter trick”!!! This is very much one of those “you don’t know what you don’t know” situations. I didn’t serve with the M16/M4 platform and I wasn’t a Gunners Mate anyway. It seemed like an easy change over and it did indeed function. Again, thanks for saving me from woe and damage to the rifle.
After watching an Autopsy… I get paranoid and want to start digging into my builds… measuring everything! 😂 I learn everytime! Thank You brother, for passing along knowledge that you could keep to yourself! A credit to gun culture! 🇺🇸 Less accidents creates less “news”… to be sure.
I've watched a couple of your videos now, and I must say you are a good teacher. I have worked on ak's and other machine guns for 3 years and havent done AR's all that much and want to learn. Its funny that my initial gut reaction to this was to just "tighten the buffer tube", but then I always remembered working on AK's. Usually, its not the part that you SEE thats the issue, its something more. And wow, that gas port is INSANE. Usually ak74's run a .74 or .080 gas port and even that is considered "overgassed".
Not sure about everyone else who has one of these rifles but I have one from this company and it’s been an absolute work horse and not once has it given me issues. Maybe I got lucky with a good one but I 100% trust it to work every time I pull the trigger.
Great video Chad. If you get any feedback from Black Rain, please let us know. For a company that pretends to manufacture a "higher end" product this was a pretty brutal smackdown that you just handed them, and rightfully so. I've had a personal opinion that BRO makes guns for people who want a flashy gun but don't intend to actually shoot it, and this video only reinforced that idea.
Not a "smackdown," the point is not to destroy or crush a company but to diagnose problems. What mindset takes you to where "smackdown" is the idea chosen?
@@seanoneil277 Did you watch the video Sean? This was about as close to a "smackdown" as Chad will ever give. I understand that it's a "sample size of 1" but as a guy who's handled more than one BRO rifle, I have found them to be very unimpressive, especially considering the price point.
@@bobcroumlich6888 I'm talking about why you want to see it as a "smackdown." Do you have a beef online with someone who touts that brand, or something? What makes you invest this autopsy with "smackdown" qualities? Who are the boxers in the ring of your mind?
@@seanoneil277 Why do you want to defend a company that is selling a 1400 rifle with this many quality issues? it's disgraceful I mean it's a perfect example of shoddy workmanship.
Your evaluation of a entire rifle was Outstanding! So many times you have checked different parts, but this was so much better. It really is the sum of all parts.....good part offset bad.....bad parts make up for the grossly over sized gas port..... Great Stuff! 👍🇺🇸
I bought one of these, the only reason is because i liked the green camo for my wife. Its pretty generic but i haven't had issues. I did a video on mine compared to my 80 build on my channel. my castle nut was loose
Woah. I'm won't be buying one of those. I feel bad for the customer. Excellent video, great knowledge, and extremely informative. Thank you again keep the vids coming.
I know this is just one of BRO firearms. But I have to say I'm glad I passed on this brand AR after watching this. I ended up going with the Springfield Armory Saint Victor instead. I've been real happy with my saint victor as well.
Instructor Chad, Wow. Thank you for opening my eyes to the extended world of AR maintenance. This video was very educational for me. I am not an armorer of any kind and you certainly do have (and need) some specialized tools that make your determinations very black or white. Kudo's to you. Please keep these videos coming.
I have a spec 15 and it ran fine only when I field stripped it I had unusual wear on the bolt…checked head space and it was out of spec from the factory. Reached out to Black Rain and they fixed it and replaced the barrel for good measure with a better .223 Winn barrel all under lifetime warranty. I really appreciate the customer service. Seems like a totally different issue than this gun but just saying they stand by their product
Im actually about to interview with the company. Im excited and hopefully i get it. I havent really known much about their products specifically, but hopefully i get to learn
Thanks for continuing to do these and talk through every aspect of the possible problems and how to fix them....have learned more watching your videos over the past few years than anything except getting hands on!
I really would like your input on what manufacturers have the most spec failures from your inspections. I feel that a rating list from you would be one of the most trustworthy sources on the planet and would benefit the consumers in such an inlfated economy.
I love your videos. It makes me want to get all of my ar-15's out and check everything. I think that dust cover flopping around would've drove me nuts.
Just got the notification. I wanted a Black Rain Ordinance really bad back in the day, when I first got into AR-15’s. I’m interested to see how this goes.
@@KeterMalkuthI was a newbie and I was impressed by the roll marks I guess lol. I didn’t really know much about ARs, I just knew I wanted one. Sounds pretty dumb now, that I would have made my whole decision for my first gun on roll marks and advertising. Chalk it up to being young and dumb I guess lol.
Owner has decided to use the BRT Gas Tube to correct the oversize Gas Port.
All of the parts to make this gun run right will cost about $250.
-JP Titanium Firing Pin
-Colt FPRP
-Colt Receiver End Plate
-Sprinco Gas Rings
-Sprinco Ejector Spring
-Sprinco 5 Coil Extractor Spring
-Sprinco Blue Buffer Spring
-Sprinco Hammer Spring
-SOTAR Carrier Key
-SOTAR Spirol Pin Kit
-OCKS Carrier Key Screws
-BCM Gas Block
-BRT Gas Tube
Thanks Chad. It's interesting how many of those parts you've used, or mentioned, in prior diagnosis and repair videos. Almost as if you know which parts can often be sub-par, and what aftermarket items are best used as replacements! 😉
That shortened buffer spring -- that suggests it was too short to begin, rather than something has compressed it over time, doesn't it?
You knew there would be score marks from the BCG striking the lower at the extension tube!
This autopsy being so comprehensive, it's almost like a perfect cadaver for teaching the common failure/flaw points. Thanks as always.
@@seanoneil277 I believe the spring was short for 2 reasons. 1) because it had some use (some cheaper springs can go bad in a few thousand rounds), and 2) it's a cheap spring. Based off of the bore scope (done after the video), the barrel has at least 500 to possibly a couple thousand rounds. It's seen some use, nothing significant though.
@@SchooloftheAmericanRifle Thank you. I shouldn't be surprised that some assemblers would use a substandard spring, after seeing substandard quality in other parts in your prior videos.
Every time I watch one of these autopsies I'm grateful for all that I learned from your SOTAR videos before I assembled my first one. Your SOTAR video library is the next best thing to taking your class, and I took full advantage of the library. These autopsies now feel like confirmation of what I learned from your videos, and how that informed my part choices. Happy 4th to you and your family, Chad. Thanks.
@@seanoneil277 most companies cut corners with fasteners, roll pins, springs, and buffers. Tungsten for an H buffet is not cheap.
What BRT gas port size is correct for this rifle? And what do you recommend for a 20" Rifle Length Gas system?
I think the worst thing about this gun is the logo isn’t in enough places. They really dropped the ball there.
The early 90's me would've LOVED all those biohazard logos lmao. 😂
Well... It so happen that the buffer is missing the logo. lol Might not be original.
Utterly clowny
I found myself wondering who made it on multiple occasions
😂 underrated comment.
Perhaps it would have run more reliably if they had just put a few more BRO logos on it.
They probably wish there were none on this one 🤣
BUT HAVE YOU HEARD OF BLACK RAIN ? YOU KNOW, the popular AMERICAN ORDNANCE COMPANY ?
If they are anything like horsepower stickers on a car, then I say this is a .338 lapua AR platform
they were on the verge of greatness
LET IT RAIN (chips off of the bolt carrier)
Damn that charging handle on the detent trick was worth the watch alone. Thank you good sir
Can confirm. This channel is a gold mine
Right!? Never knew that tip/trick… but it will forever be used now.
Thanks for the comment, I might have missed the tip in the video.
Time stamp? What trick?
To me, the most interesting aspect of this autopsy is how the leaky gas block, loose gas key, and inefficient bolt carrier partially “correct” that gaping gas port. By putting a known-good BCG in the gun, you demonstrated that it wouldn’t run right even with a heavy spring and heavy buffer. This emphasized how the entire system must interact correctly. You also demonstrated how you can chase your own tail unless you understand WHY the gun isn’t running right in the first place.
Thanks!
I like to think of it as a 1-cylinder version of a car engine. If you had a leak in your intake system (carb/manifold interface, manifold/head interface, or along the manifold runs) your engine would be wheezy at best and maybe wouldn't start or stay running if it sparked over. In the AR the gas drives the engine and it needs to be metered properly for all the parts to be happy working together. Otherwise you have a fancy overcomplex bolt gun, with parts meant to work a bit unlike a bolt gun does.
Someone up above in a stand-alone comment mentioned the overgassed nature of the huge gas port was offset by the leakage at the wobbly gas key. Either alone would have been a fairly straightforward Dx but together they offset each other and made Dx confounding. Add in the buffer and buffer spring weakness and that's a lawn mower that won't start or won't stay running when it does.
heh, I was thinking the same thing right before I read your comment. Interesting how the combo of over-gassed, loose gas block and carrier key is a trifecta of problems that kinda sorta cancel each other out a little. At least it kept the gun limping along for a little while.
rifle looks used up and the buffer is not factory. No issues here.
He got the rifle on a trade could it have been abused beforehand or not?
🍿
Thank you to both of you for doing these. The quality of the content in just production, when the purpose is not to make money, says a lot about both of you; but that the information in these videos is of such a high quality and the result of such investment, and that we can all take advantage of that, thank you very much indeed.
You're welcome. 😊
Thank you very much
Might be your coolest, most entertaining autopsy yet. Thank you for just running it, br0.
I like how it has BLACK RAIN along the whole handguard as well as every single open space on every part of the entire rifle. LOL
Always good to brand as "Black Rain" when along comes a QC check to verify it's merely "Pale Drizzle."
I learn more watching one of your autopsy videos than I do watching 20, “What is the best AR 15 to buy?“ videos. Thanks!
42 minutes well spent. The AR is about balance, and learning how minor differences interact is valuable. Thank you.
Truly a meme tier rifle.
I think the most refreshing thing for me, from this video, was the appreciation for your diplomacy. Most YT gun personalities would have just trashed the maker. You listed your observations , judgement free. That must have been a challenge, so bravo.
Happy 4th.
Great video Chad, I can't image the owner wanting to stay with that barrel...plenty of quality barrels out there that won't break a budget...
“Let it rain” a single drop
I really enjoy how thorough you are with your examinations and the detail you go into when describing the issues as you come across them. I always learn something with every one of your videos, and I thank you for that! Cheers
bro this is one of the best channels on youtube. such much great info. cheers
I think that your wife does an excellent job with the camera work.
She does. Sometimes I forget someone else is running the camera because she's always focused on what Chad is talking about. I noticed when Chad was listing all the things wrong and was forgetting something, she would focus on that to give him a hint.
@terrytolentino5459 Thank you! 😊
@GentlemenBronco We were laughing about me doing that!! 😂
Thank you. I believe she is the star of the channel. I wouldn't make videos without her help.
@@SchooloftheAmericanRifle🥰
the amount of knowledge displayed here about this particular platform is just astounding! thank you for sharing with us.
My great appreciation for your expert tutelage. For those willing to learn, the knowledge you present is like food to a starving man. As I continue my journey through custom building and problem diagnostics, your videos serve as my classroom. I have learned a lot about how the gas/BCG/buffer systems work together, but this video just took me up another notch. Friend, you can consider me an apprentice. Thanks again.
Another amazing video.
Learn something new every time I watch one of your videos.
I'm in the middle of building my first AR-15 with a 3D printed lower receiver and a freedom rifle kit from Palmetto State Armory... videos like this have been super helpful to carry me through, thanks for making!
Wouldn’t bother with the 3D printed lower, longest me and the boys have ever been able to get one to run is about 500 rounds. Past that point, they break at the receiver extension. Just buy a lower off palmetto, they’re like $160. The government knows where you live and what you buy anyway.
The government also loves when people broadcast on public sites that their building ghost guns from 3D printed devices lmao
@@cmp9338 OH NO SO SPOOKY 👻
@spacecaesar7619 I think palmetto had a blem lower for Luke 25 dollars over the weekend
@spacecaesar7619 yeah but 3d print design account for failure points. The orca AR15 has a 3d printed upper and a lower, those rifles can run thousands of rounds.
Chad, this is perhaps your greatest video to date.
Impressed that you dont cut away and edit out the little errors. Continuous video says it all when it comes to trusting that someone truly knows what theyre doing.
Probably the best video I have ever seen when it comes to trouble shooting an AR, perfectly demonstrates that without the knowledge of how the gas system works and needs to be balanced, you could chase problems on this rifle in a circle. You fix one issue that exacerbates another because how off the balance of the rifle was, I could see this rifle driving someone crazy.
Great autopsy. It’s been a long time since I’ve seen a rifle this poorly made.
HAPPY 4th guys!!!
Wow, this is a great video. I suddenly want to get a bunch of gauges and check all my stuff.
This is so inspiring... I do work on and fab minor parts for my firearms, but I am a general machinist, not a gunsmith. Watching the methods is inspiring, and watching the knowledge/experience involved is humbling. I will continue to apply what I learn from this channel on my existing LR-308's and AR-15 type rifles. I can't wait to compare Colt to Windham to PSA.
Thank you for sharing so much knowledge, experience, and wisdom.
It’s slow at work and these vids get me through the day.
Loved the video, great insight into how all the parts must come together for a well operating system in the M4 platform.
Hey I was at a gun show and they had a booth . I liked the way the Plankton Ranger looked and handled but something told me no . I'm 62 so here is a life lessson ,"Never Impulse buy. Thanks for the video 😎
Chad, thank you & the Mrs’s so much for another highly informative video! Always love learning more & greatly appreciate the lessons!So excited these videos are back!
Our pleasure! Thank you
Thanks for putting this out Chad, great content as always
This is one of your best vids so far! It takes a failure like this to fully understand how all the parts work together and what is required for proper function. Everything clicked when you gauged the gas port...I immediately visualized the entire pathology of the rifle.
You don't know
I lived in Neosho, MO and bought my first AR barrel, a Black Rain. I was hoping for sub MOA accuracy out of it, but it was more like 2 MOA, so I did not buy any more of their products...good thing. Thanks for doing what you do!
@jaquesrabit8400 probably, but then, statistically, so are you.
How could people not like you. I would chill with you. Especially at the range...
I gotta say, as a former Naval Architect/Mechanical Engineer who used to work closely with machinists, what you do is exhibit A for why machinists and folks like them are so darn important. Sure, engineers can design something, set tolerances, do fatigue analysis, etc., but if you don't run your design by a machinist or someone who has your type of niche expertise, you more than likely will screw something up. I know because I've done it, to the tune of more money that I will ever admit.
All the training and education in the world doesn't compare to hands on no BS experience and the "been there done that" aspect of things.
Thanks for sharing this stuff. Now excuse me as I go on to do another AR-15 build with a Nitride BCG!
Looking forward to part 2. I do enjoy these videos. Much to learn from them.
Learned a lot about AR’s from this video. First how good the guy is that has built all of my AR’s. Never had any of these problems and they all shoot great, at half price of this gun. Plus maybe its more important to spend more time on quality control that on laser engraving the logo on every possible piece of the gun. Thanks for the video.
Chad, thanks for making this video I am always learning from you.
Tons of info here. Thanks Chad, great break down.
I had a PSA that had a .93 gas port, some of the same issues this one had.
Thank-you Chad!!! I often “watch” your videos by letting them run in the background (on the TV) while I work on something else. Not this time though!
This video helped me identify a problem that I didn’t know I had, and address it BEFORE damage had occurred. When I switched to a Magpul PRS stock on the 3-Gun rifle I use for long-range stages, I grabbed my longest spring and longest buffer out of my parts bin. It was supposedly an “easy” change over… didn’t know my BCG was traveling too far into the extension and the gas key was hitting the receiver. Thanks for the “quarter trick”!!!
This is very much one of those “you don’t know what you don’t know” situations. I didn’t serve with the M16/M4 platform and I wasn’t a Gunners Mate anyway. It seemed like an easy change over and it did indeed function. Again, thanks for saving me from woe and damage to the rifle.
The Chad we all strive to be
I watch these videos to remind myself I have alot to learn. Thanks for the online classes.
Best AR videos on UA-cam. Thanks so much for all the information
After watching an Autopsy… I get paranoid and want to start digging into my builds… measuring everything! 😂 I learn everytime! Thank You brother, for passing along knowledge that you could keep to yourself! A credit to gun culture! 🇺🇸 Less accidents creates less “news”… to be sure.
I've watched a couple of your videos now, and I must say you are a good teacher. I have worked on ak's and other machine guns for 3 years and havent done AR's all that much and want to learn.
Its funny that my initial gut reaction to this was to just "tighten the buffer tube", but then I always remembered working on AK's. Usually, its not the part that you SEE thats the issue, its something more. And wow, that gas port is INSANE. Usually ak74's run a .74 or .080 gas port and even that is considered "overgassed".
Also, I live super close to BRO and have heard about working there. Its not bad, but it doesnt pay well.
this is amazing. you and joe chambers. math don't lie.
Not sure about everyone else who has one of these rifles but I have one from this company and it’s been an absolute work horse and not once has it given me issues. Maybe I got lucky with a good one but I 100% trust it to work every time I pull the trigger.
Always enjoy your deep dives. I mean you even gave the chamber a good ole fashioned pap smear.
Great video Chad. If you get any feedback from Black Rain, please let us know.
For a company that pretends to manufacture a "higher end" product this was a pretty brutal smackdown that you just handed them, and rightfully so.
I've had a personal opinion that BRO makes guns for people who want a flashy gun but don't intend to actually shoot it, and this video only reinforced that idea.
Not a "smackdown," the point is not to destroy or crush a company but to diagnose problems. What mindset takes you to where "smackdown" is the idea chosen?
@@seanoneil277 Did you watch the video Sean? This was about as close to a "smackdown" as Chad will ever give.
I understand that it's a "sample size of 1" but as a guy who's handled more than one BRO rifle, I have found them to be very unimpressive, especially considering the price point.
@@bobcroumlich6888 I'm talking about why you want to see it as a "smackdown."
Do you have a beef online with someone who touts that brand, or something? What makes you invest this autopsy with "smackdown" qualities? Who are the boxers in the ring of your mind?
Price point on this rifle is somewhere between $1200.00 and $1400.00.
Black rain ordnance deserves a SmackDown for selling this kind of trash.
@@seanoneil277
Why do you want to defend a company that is selling a 1400 rifle with this many quality issues? it's disgraceful I mean it's a perfect example of shoddy workmanship.
The mag that comes with this binds up. Mag pull works well and so do the metal ones from the Corps. Great video sir
I appreciate how you show in detail, how tolerance stacking on parts can and will lead to failures..
Your evaluation of a entire rifle was Outstanding!
So many times you have checked different parts, but this was so much better.
It really is the sum of all parts.....good part offset bad.....bad parts make up for the grossly over sized gas port.....
Great Stuff! 👍🇺🇸
I bought one of these, the only reason is because i liked the green camo for my wife. Its pretty generic but i haven't had issues. I did a video on mine compared to my 80 build on my channel. my castle nut was loose
Top notch video as usual. Love learning about all the small tips and details about these rifles and their components
This video was very educational. It fired me up to become a gunsmith. Highly enjoyable (for people like me). Keep up the good work.
The most satisfying and informative video I’ve seen in ages. THANK YOU.
Another great video!! I am one of the guys that tries to learn something from every video and this is no exception. Thanks for teaching us!!
Very thorough, thanks for sharing. Looking forward to Part 2.
Very informative, thank you for taking the time to make this video!
Very entertaining and informative. Thanks!
No equivalent content anywhere else on UA-cam
Good stuff brother, it's appreciated
Man, i love watching your autopsy videos. This one had me on the edge of my seat like watching a murder mystery. Cant wait for part 2. Thank you...
Yes I've been waiting for this one since it came up on fb!
Woah.
I'm won't be buying one of those. I feel bad for the customer.
Excellent video, great knowledge, and extremely informative. Thank you again keep the vids coming.
You are nuts but in a brilliant way. Thank you so much
Nice breakdown. 🕵🏻♂️ 🇺🇸
I know this is just one of BRO firearms. But I have to say I'm glad I passed on this brand AR after watching this. I ended up going with the Springfield Armory Saint Victor instead. I've been real happy with my saint victor as well.
I'm not sure you made a much better choice. The saints have their own host of QC issues
Instructor Chad, Wow. Thank you for opening my eyes to the extended world of AR maintenance. This video was very educational for me. I am not an armorer of any kind and you certainly do have (and need) some specialized tools that make your determinations very black or white. Kudo's to you. Please keep these videos coming.
Very very informative. I always learn from your videos. More than usual from this one
Excellent Video!!! Thank you for sharing. Looking forward to part 2.
I have a spec 15 and it ran fine only when I field stripped it I had unusual wear on the bolt…checked head space and it was out of spec from the factory. Reached out to Black Rain and they fixed it and replaced the barrel for good measure with a better .223 Winn barrel all under lifetime warranty. I really appreciate the customer service. Seems like a totally different issue than this gun but just saying they stand by their product
learned a lot in that one!
Very informative video. As always
Learn something everyday! Thank you for your service to our community!
Excellent video!
Excellent video ! Thanks
Your vids are amazing. I wish I knew about you 10 years ago before I moved away from MD. Keep up the good work.
Another great video Chad, thank you
I love these longer videos. Maximum knowledge and comfort
Definitely some issues with this one. Thanks for working through the issues with us. Learned a lot, always appreciated
Awesome video , very informative.
Im actually about to interview with the company. Im excited and hopefully i get it. I havent really known much about their products specifically, but hopefully i get to learn
Is this a joke? 😂😂 I
@@mikebrown4433 yeah they were fucking terrible about responding
Thanks for continuing to do these and talk through every aspect of the possible problems and how to fix them....have learned more watching your videos over the past few years than anything except getting hands on!
I really would like your input on what manufacturers have the most spec failures from your inspections. I feel that a rating list from you would be one of the most trustworthy sources on the planet and would benefit the consumers in such an inlfated economy.
I love your videos. It makes me want to get all of my ar-15's out and check everything. I think that dust cover flopping around would've drove me nuts.
Thank you so much for your videos. I learn a great deal when I watch every one of them. Thank you for taking the time to teach us time to teach us.
Excellent video , keep up the great work!
Thanks for posting this. I appreciate the learning experience.
Good stuff. I always learn something.
Chad! I really enjoying way you educate us! Very well spent time to watch! Thank you!
Another very informative video! Happy Independence Day everyone.Thanks to both of you!
Really enjoyed this video and felt that I learned a lot! Thanks!
Love the channel always good info 👍🇺🇸
Just got the notification. I wanted a Black Rain Ordinance really bad back in the day, when I first got into AR-15’s. I’m interested to see how this goes.
Looks like it's a good thing you never got one haha
@@Eastahtata Yeah that’s what it’s looking like lol.
@@KeterMalkuthI was a newbie and I was impressed by the roll marks I guess lol. I didn’t really know much about ARs, I just knew I wanted one. Sounds pretty dumb now, that I would have made my whole decision for my first gun on roll marks and advertising. Chalk it up to being young and dumb I guess lol.
@@brian_b_musicyep that's exactly who they target for their marketing. Those who don't know better.
Love your videos. I’ve been working with the AR/M16/M4 platform for many years, but always learn something from your presentations.
With the headspace issue and gas port size, it seems like a new barrel is a good option. Killing off multiple problems at once.
Don't forget the rough chamber and the feed ramps! What they did to that barrel made me cry.