Це відео не доступне.
Перепрошуємо.
OpenTX Inputs, Mixes, Outputs Explaned Via Adding Switches
Вставка
- Опубліковано 19 гру 2020
- Get your stuff here:
RDQ Bardwell F7 30x30 Stack/Combo (JBF7 FC and 32Bit 50A 3-6s 4in1 ESC) at Race Day Quads - bit.ly/RDQBard...
Bardwell F7 Flight Controller at GET FPV: bit.ly/Bardwel...
iFlight 2207 Size Motors at GET FPV: bit.ly/iFlight...
ifFlight 2207 2750 kv Motors at RDQ: bit.ly/2207-27...
VTX similiar to the one in the video: amzn.to/39NaHl1
Options for FPV Quadcopter Frame - amzn.to/3ord7dV
FrSky R-XSR Ultra SBUS/CPPM D16 16CH Mini Receiver - amzn.to/3dSNVYU
Radiomaster TX16S at Amazon amzn.to/3lifqP1
Radiomaster TX16S at RDQ: bit.ly/TX16s-a...
Radiomaster TX16S at GET FPV: bit.ly/TS16sMAX
Ovonic 4S 1550mAh 100C 14.8V LiPo Battery - amzn.to/3kuwMY5
Caddx Rattel FPV Camera - amzn.to/3juScmy
FPV Camera Transmitter Options: amzn.to/3krQ80b
FPV Racing Drone Props: amzn.to/3a5xTaw
FPV Goggles and Receiver: amzn.to/3b6fOuy
1-6S 30V Smoke Stopper Amass XT30/XT60 - amzn.to/2HENshq
More Stuff:
Tenergy TB6-B Balance Charger Discharger 1S-6S Digital Battery Pack Charger: amzn.to/2Xwq5vT
Aluminium Standoffs: amzn.to/3eepCol
Black Spacers / Plastic Standoffs: amzn.to/2Rw4nVi
White Spacers / Plastic Standoffs: Spacers / Plastic Standoffs:
Drone Buzzer: amzn.to/2XxHBQs
Multimeter: amzn.to/2Rw5PHe
Soldering Iron (Budget): amzn.to/2XwlV7p
Soldering Iron (Much Nicer option): amzn.to/3cfuCHc
Soldering Station with Hot Air Gun as seen in video: amzn.to/2xhgui9
60-40 Rosin-Core Solder (LEAD): amzn.to/34zsx6h
Solder (Lead Free): amzn.to/2Ryp2I1
Helping Hands (Basic): amzn.to/3chQGRN
Helping Hands (As seen in video): amzn.to/2KdkyTr
Mini Screwdriver Set: amzn.to/3a20BsZ
Screws & Nuts: amzn.to/3ccjKtM
Heat Shrink Tubing: amzn.to/3c8gUG6
Rapstrap Cable Ties: amzn.to/2RBdzYt
Zip Ties: amzn.to/3ckqdDb
4pcs Hex Screw Driver Tools Kit: amzn.to/3a4Jo23
Magnetic Parts Tray: amzn.to/2XxZC1g
THIS PLAYLIST: • RDQ Bardwell F7 FPV Qu...
Radiomaster TX16S Beginner's How To Series - • Radiomaster TX16S Begi...
Inputs/mixes discussion starts at 4:25. thanks for this!
Fantastic video. If you aren’t already, you should be a teacher.
I’ve been with this hobby two years this July and I have yet to see a video on the inputs, mixers and output this well done yet.
Definitely subscribed to your channel and looking forward to watching your previous and new videos.
Cheers,
Sam (from Canada)
Hi Steve. If we setup the modes in betaflight anyway then what is the advantage of adding the various ranges in the mixes? Doesnt betaflight override that anyway? Couldn’t I name something arm switch on my controller but in betaflight assign it to beeper or whatever? Thanks in advance.
Brilliant!
So can i not change the function of the switch on the radio without betaflight? Can set the arm/disarm to work, without betaflight?
IMHO it is a little overkill to set switch in the radio this way. I just add a single mixer line on the channel with the switch as a source. Works the same way. For the rest of the video I found it very informative and I have learned new thing or two :-)
Good tip! Your way is definitely easier. I do it the long way in the video because when I learned how to do it, seeing 3 lines (for a 3 pos switch) laid out on 3 separate rows made it easier to wrap my brain around what was going on.
@@TahoeSteve I noticed the benefit of having things named on each position. OTOH when I set arming switch on each model the same way, I do not need to emphasise each position, as it is obvious. For a tip - you do not need to start the radio in the bootloader mode to use the SD card. Connecting the USB cable should be enough, unless you configured the USB for joystick emulation only.
Hello Steve, your video was clear to understand each step configurating the Open TX companion on the Radiomaster TX16S. The radio reflected perfectly the data so, I could check that all the information was saved over there. But on my case I found no interaction or connection between the radio and betaflight on the receiver tab, is that a sign that they were not bound? Is it truth that the binding procedure does not have to be repeated, until one of the parts is replaced (manual text). I just repeated several times the binding without exit.
Hello
I need to control TX16S using UART through GUI. Any idea please
Hello sir I'm new to this can you please help me I have a betafpv 85 pro2 and a jumper tx18 my problem is when I arm it the motor is not turning and about the throttle it is already halfway up before I can see the motors turn and when I pull it down the drone just jump and turn over, and when I push it beyond the halfway point the quad just jumps and zoom up. How do I fix that in my transmitter or betaflight Thank you
I have one question, the S3 solder connectors on the back board of my taranis X9D Plus SE 2019 are marked GND - V5 - SP.
What ist the meaning of V5 + SP ? 🤔
Hi neighbor, West Charlotte here.
Have any recommendations for flying fields around here just getting into quads 🤷🏿♂️
But why do we need the "Inputs" in the first place? What benefit does this give me when in the mixer, yes, I select the [ARM] input as input.. but then i have to manually select the SF switch there again? Can't wrap my head around it..
You dont. But that is the way i learned it. It helps to wrap your brain around the whole process.
what does the six buttons in the centre do?
They are programmable just like the rest. As a multirotor pilot, I have never used them. I understand that people that fly planes use them a lot more.
My switches want go past 1500.
...and I'm off to Tahoe Steve home to find #1 on the TX
happy flying!