Nice refurbishing project. If you will take the neutral line input and wire it to the other leg of the rocker switch, than the switch will light up when you turn it on... Also, if you want to keep paint from getting under the tape with stencils, first do a light spray with a clear coat of paint. That seals the edges of the tape and it won't allow paint to get under the edges. Thumbs Up!
Most restoration UA-camrs will sandblast, wire brush, nickel plating. But I think sandblast, nickel plating then wire brush is much better. This restoration is perfect! 10/10
as usual the result you achieved is wonderful. your precision makes the difference and it's a pleasure to watch your videos. However, I must make a clarification about the grinder which is not rusty at all but just dirty and slightly oxidised: a good cleaning and a wipe with steel wool would have been sufficient to make it 100% operational.
Videolarınızı izlemek çok keyifli. Diğer projelerinizde olduğu gibi restorasyon işlemlerinde de tam bir profesyonelsiniz. Detaylara verdiğiniz önemi, düzeninizi ve temiz çalışmalarınızı takdir ediyorum.👌🏻👏🏻👏🏻🙌🏻 Tebrikler usta.🙂🙏🏻
Nice renovation project. you do well . You apply stone protection glue and after a few days it will peel off. I have been in the repair business for 25 years. What I usually do is rivet a few rivets, which last until they break
Remember kids.... NEVER re-use a grinding wheel that you do not know the history of ! ! ! Beautiful job as always mate = ) Hope you and yours are all safe and well.
Great job. :) Instead of oil use copper grease where the axle and bearing meet. It will last forever and prevent any rust from coming ever again. Btw..I'm a blacksmith and machinist who enjoys your videos very much.
Beautiful job. Shouldn't the frame of that grinder be connected to Earth ground to prevent a shock hazard if one of the internal conductors touches the case?
Excelente tutorial maestro, un trabajo impecable, el detalle elevado al máximo nivel, ni de fábrica salio tan bonito, gracias por compartir sus conocimientos y experiencias, un saludo cordial y por supuesto un merecido like desde Narón (Galicia)👍🤓😜
Nice job. But let me give you an advise: When you have oval holes, like th e holes in the grind stone housing, you hav to use washers underneeth the screwheads.
Hello, could you give me the site where you buy the profiled aluminum trays and the profiled aluminum bars please. thank you for helping me and answering me. Sincerely serge
Good morning for all the people who subscribe to this channel. please on the internet where you buy your aluminum profiles and trays. Thank you for your answers serge
Love your videos, but am surprised that (a) you use an adjustable wrench instead of the right-sized socket, box or combination wrench (much less chance of rounding over nuts) and (b) no penetrating oil on any of the stuck fasteners. But keep up the great videos!!!
Братцы! А это точно мясорубка??? Не, ну сдуру туда и ч.... ен засунуть можно. Но я весь ролик думал, а почему у меня мясорубка немного.... Как бы... Не такая. 😅
why was not the power cord replaced with a new 3 wire that has a ground in it, hard to come back from electrification , all of your video safety was for most hope this was a over site, your video are great enjoy the very much
If you like the video, please introduce it to your friends and social media !
Nice refurbishing project. If you will take the neutral line input and wire it to the other leg of the rocker switch, than the switch will light up when you turn it on... Also, if you want to keep paint from getting under the tape with stencils, first do a light spray with a clear coat of paint. That seals the edges of the tape and it won't allow paint to get under the edges. Thumbs Up!
Nice tips mate!
Огромное спасибо за представленные видео! Действительно ЗОЛОТЫЕ РУКИ! Есть на что посмотреть и над чем задуматься.. 👍
Most restoration UA-camrs will sandblast, wire brush, nickel plating. But I think sandblast, nickel plating then wire brush is much better. This restoration is perfect! 10/10
as usual the result you achieved is wonderful. your precision makes the difference and it's a pleasure to watch your videos. However, I must make a clarification about the grinder which is not rusty at all but just dirty and slightly oxidised: a good cleaning and a wipe with steel wool would have been sufficient to make it 100% operational.
Videolarınızı izlemek çok keyifli. Diğer projelerinizde olduğu gibi restorasyon işlemlerinde de tam bir profesyonelsiniz. Detaylara verdiğiniz önemi, düzeninizi ve temiz çalışmalarınızı takdir ediyorum.👌🏻👏🏻👏🏻🙌🏻
Tebrikler usta.🙂🙏🏻
The main body paint was fine. Just needed some clear-coat. Ahh it's great like this too. And everything else.
Awesome restoration.
Very nice that it was so clean inside. Great results, many more years of use for you in this tool.
Nice renovation project. you do well . You apply stone protection glue and after a few days it will peel off. I have been in the repair business for 25 years. What I usually do is rivet a few rivets, which last until they break
Remember kids.... NEVER re-use a grinding wheel that you do not know the history of ! ! ! Beautiful job as always mate = ) Hope you and yours are all safe and well.
Did it need repaired, probably not ... does it now look fantastic, most definitely ... brilliant 👍
Linda sua restauração, parabéns pelo profissionalismo
Amazing work, great finish👍
Gosto muito de apreciar os vídeos deste canal, o autor alem de inteligente é muito detalhista e sabe fazer as coisas
ベアリングもシャフトもキレイなグラインダーでよかったですね！
動画見ました？
Meu Deus, como é bonito o profissionalismo, adoro ver os vossos vídeos.
It looks great and you did a wonderful job restoring it as well!!!!
I enjoyed your video so I gave it a Thumbs Up
Thanks!
Very good indeed and to your usual level of perfection. Well done......
Great job. :)
Instead of oil use copper grease where the axle and bearing meet. It will last forever and prevent any rust from coming ever again. Btw..I'm a blacksmith and machinist who enjoys your videos very much.
Congratiulations, this is a beautifull restoration.👏🙏🙌
Excelente como siempre. 💪🏻 👍🏻 🇦🇷
Très belle restauration, du beau travail......comme a votre habitude.
I like that screwdriver set you're using
This
amzn.to/3uQz263
así es que se hace un buen trabajo!!!! mil felicitaciones por eso y gracias por el video no fue tiempo perdido.
Perfect restoration keep it up bro
Фантастика! Просто прекрасно )
Прекрасная работа! Сервис неправильно перевёл на русский язык название реставрируемого станка. 😂 Это не мясорубка!
Super great restoration 👏👏
Excellent 👌👌👌👌👌👌👌 Very Good Job
Beautiful job. Shouldn't the frame of that grinder be connected to Earth ground to prevent a shock hazard if one of the internal conductors touches the case?
Excelente tutorial maestro, un trabajo impecable, el detalle elevado al máximo nivel, ni de fábrica salio tan bonito, gracias por compartir sus conocimientos y experiencias, un saludo cordial y por supuesto un merecido like desde Narón (Galicia)👍🤓😜
楽しみにしてました！🎉
Quite frankly, the best I’ve seen on UA-cam yet …. 30.1.24
Amigo muy bueno todo lo que hace me gusta porque esa es mi pasión lo felicito
ああああぁお客様！！！困りますお客様ぁぁぁぁ！
勝手に新品以上の修繕をされてしまっては私共困り果ててしまいますう🤣
Lovely Job sir!
Grossartiger Job!! Exzellent ausgeführt. 👌👍👍👍
Во‼️
Давненько не было🤷🏻♂️
Булатный лайк мой👍
Чётко! Красота😍💓
Qui abita l'eleganza!!
Nice job. But let me give you an advise: When you have oval holes, like th e holes in the grind stone housing, you hav to use washers underneeth the screwheads.
Как всегда великолепно😊
Great job 👍
Can't believe that's a genuine New Strong!!!!
11:27 I was afraid this would happen. Those tapes prefer tearing than being removed.
Wouldn't it be easier to etch it with acid?
Que original queda todo lo felicito
This is funny to finish by believing that you actually build it.
There is a lot of features that I would have liked to see build.
Domo Arigato.
Very nice
Lovely video
こんばんは🌙😃❗
凄いで上手いで良い!😆👍️
Hello, could you give me the site where you buy the profiled aluminum trays and the profiled aluminum bars please.
thank you for helping me and answering me.
Sincerely
serge
Looks better than new.
Не знаю! Наверно так и помру не узнав для чего он мыл корпус?🤣
Для нечего делать мыл корпус.
А в названии ролика нет ничего необычного?????
Мясорубка😮
when u sandblast it why wash needed?
One more thing this needs is some perspex shields, can never have enough eye protection.
Thank you for sharing, I always look forward to your videos. What flow rate is your compressor for your sand blaster?
0.3MPa
@@jisakukobo ~= to 43.5psi....Think he is asking for CFM/(M^3/hr). I'd like to know that also, please.
It's a good practice to replace old electrical cable with a new one. As the rubber gets, old it tends to break exposing live wire.
Yes, and replace it with a 3 wire (grounded) one and ground the housing.
Pero mas que reparar es restaurar, gracias x tu video
Нож ремонт работы 🙋🏻👍👍🏻👍🏿👍🤣🤣🤣🛠️🔧📹 посмотреть интересно
Trabalho de mestre
3:05 This divided housing is interesting.
No dust extraction. It is extremely dangerous to breathe this dust. You need to attach a vacuum cleaner to the casings.
Perfeito, nota 10
Good morning
for all the people who subscribe to this channel. please on the internet where you buy your aluminum profiles and trays.
Thank you for your answers
serge
Superbe 👍👍👍👍👏👏👏👏🖐🏽🖐🏽🖐🏽🖐🏽🖐🏽🖐🏽
Beautiful
stunning!
なぜプラスネジやめてマイナスネジ使ったのでしょうか？固着した時取りやすいとか？
単に手に入らなかったのです。ネットも含めて
これ、インチねじなんですよ。
ほう〜ハーレーいじった時以外インチネジに当たったことありませんでした。我が家にも同じようなグラインダーが2台あるので確認してみます。
1:21 What tool is that?
I'm also interested in the answer
Love your videos, but am surprised that (a) you use an adjustable wrench instead of the right-sized socket, box or combination wrench (much less chance of rounding over nuts) and (b) no penetrating oil on any of the stuck fasteners. But keep up the great videos!!!
That's a first I've never seen someone do plating with a battery for the power source
раз у них такие мясорубки - боюсь представить как у них выглядят точило
Super 👍👌
Братцы! А это точно мясорубка???
Не, ну сдуру туда и ч.... ен засунуть можно.
Но я весь ролик думал, а почему у меня мясорубка немного....
Как бы... Не такая. 😅
why was not the power cord replaced with a new 3 wire that has a ground in it, hard to come back from electrification , all of your video safety was for most hope this was a over site, your video are great enjoy the very much
Grounded electrical outlets are a minority in Japan.
Если это мясорубка , то я президент . 👍
Вал в идеальном состоянии
moedor ?
perfect
Трогая руками голый метал знай на твоих руках есть пот который дает 100% окисление метала и краска через время все равно в том месте отойдет!
特別な魅力は、平らなスロットを持つネジです！
保護透明バイザーを固定するための未使用の場所がありました
あれは透明バイザーを固定するための金属ではありません。
もともとは砥石ブレーカーの為のものです。
Суппер🤟
Теперь можно и на рояль поставить!
Mistrzu! :)
Super works
سلام
ایده های شما تمام شده قبلا بسیار موارد خواصی آموزش میدادید
Это не мясорубка,а точильный станок.
Ремонт Мясорубки 😂 а где Мясорубка ?
Translation into Russian is wrong. "Meat grinder" is not the same as "grinder"
I thought meat grinder was pronounced "Bakhmut" in Russian.
"Grinder", in Brazilian Portuguese has lots of translations and the one in the title is wrong too. 😂😂
♥️👍
Ça va, il y a pire comme état, c'est dommage que l'ancien propriétaire n'ait pas pris plus soin de son outil.
👍👍👍👍👍👍👍👍👍👍👍👍👍......
А причём тут Мясорубка? 🤔👎
26:20 It's a pity you didn't solder these elements.
Whatever works ;)
у меня перевело на русский язык, как ремонт ржавой мясорубки))))
相変わらずスゴい手際や(´・ω・｀)
Grinds my gears that he did not clean off the muck on the outside first.
Так это ржавая мясорубка, кофемолка, или....?
Норманый станок был, не надо было ничего и делать, покраска на функционирование не влияет.
👍👍👍🔥