Kawasaki and others 2 stroke ignition system

Поділитися
Вставка
  • Опубліковано 16 гру 2024

КОМЕНТАРІ • 327

  • @vinnyvinson
    @vinnyvinson 2 роки тому +2

    Thanks! I wish I would have known this before I got into my tc90. Got the puller and flywheel off…it sparked before kickstarter stuck. Had to get whole new (ts) bottom end. Now I’m chasing spark issues again. Looking at grounds and bought new condensers. With your help I’m sure I’ll figure it out eventually. This video was key in helping me understand spark. Well done

    • @2strokeguru
      @2strokeguru  2 роки тому +1

      Thank you check and clean or replace points

    • @vinnyvinson
      @vinnyvinson 2 роки тому

      @@2strokeguru I will

  • @jordangoldenberg9264
    @jordangoldenberg9264 3 роки тому +2

    Thank god I found this guys videos. I got a ‘74 g3ss and there’s next to no info on them.

    • @2strokeguru
      @2strokeguru  3 роки тому

      Thank you that's why I made this channel

  • @OnlyNotes
    @OnlyNotes 4 роки тому +2

    I just picked up my first bike; a 71 Kawasaki F6. I'd be totally lost without your videos for help... Thank you!

    • @2strokeguru
      @2strokeguru  4 роки тому

      Thank you you are welcome

    • @OnlyNotes
      @OnlyNotes 4 роки тому

      @@2strokeguru Hey again, I've been looking at my bike and I've noticed a new problem. I'm hoping you can help, you seem pretty experienced with these engines.
      The bike has a 125cc motor and when I turn the engine over by hand (or turn via kickstart), oil is coming out the mouth of the carb. I know the bike has sat for years with a full oil tank... what I'm wondering if oil hasn't leaked past the oil injection pump over time and somewhat flooded case with oil, and while hand-spinning the motor, maybe it's just sloshing the oil around until it comes out the carb. I can't find any other instance of the issue online so I'm confused... The oil colour is green, I don't think it would be fluid from the gearbox...
      If it helps to know, this problem occured when I first got the bike, and still occurs after I removed the oil injection line from the case. I haven't started the bike yet, and the carb was cleaned to spotless condition before I noticed this weird oil leak.
      My question, why is there an excess of oil in the crankcase?.. also how do I get it out?... there wouldn't happen to be a drain bolt from the crankcase on this motor, would there?
      Thanks!

    • @2strokeguru
      @2strokeguru  4 роки тому

      @@OnlyNotes call me 603 3958097

    • @OnlyNotes
      @OnlyNotes 4 роки тому

      @@2strokeguru I don't have international calling... and I actually figured it out with the help of a friend. I took the carb off and left the bike on it's side to drain the excess oil from the crankcase

    • @2strokeguru
      @2strokeguru  4 роки тому

      @@OnlyNotes yes drain it out

  • @chuckgilbert2035
    @chuckgilbert2035 Рік тому +2

    Thanks, I did learn something, annoyed by the movement of the camera but maybe I watch to much youtube

    • @2strokeguru
      @2strokeguru  Рік тому +1

      I do the best I can not exactly making money putting out free 30 plus years of experience

  • @framncesmaddox9042
    @framncesmaddox9042 5 років тому +4

    Can you post a video of what the whole wiring harness looks like behind the stator can't really see what wires go where

  • @VashStarwind
    @VashStarwind Рік тому +1

    I had to swap engines, and took the stator off the new engine, and put the old stator that was on the original engine to the bike on the new engine, because the harness plugs were different. Would I use the magnito off the original engine also? Other words do I keep the same stators/magnitos together? Or does it not matter?

  • @murrayminimotors1674
    @murrayminimotors1674 3 роки тому +1

    I have a 1983 KDX 80 I bought in pieces so I do not need a CDI box what you're saying I do only have the one wire coming out of there so go to the kill switch straight to the coil and I should have spark?

  • @milwaukeebrewcrew484
    @milwaukeebrewcrew484 3 місяці тому +1

    Now how do I wire the cdi? I have a kz200 that has points the wiring the coil helps a lot I didn’t know it split. I can start the engine by putting the wire to the coil then jumping the starter but I need to hold power to the coil to get it to run

    • @2strokeguru
      @2strokeguru  3 місяці тому

      You will have to get a cdi conversion kit my cdi ignition system is completely different I believe boyor makes one for bike it will have step by step instructions

  • @dbmsalce
    @dbmsalce 2 роки тому +1

    Hey I’m having a no spark issue with a 1972 Suzuki rv90 it has a big white coil like that one I’m not sure how to test it where to put the meter leads and what ohms Would be considered good or bad, I also am new to the points ignition system, I can barely find any info on this bike anywhere

  • @swektmaico
    @swektmaico 2 роки тому +1

    What would be your best suggestion for a CDI 12V magneto system for a KE125 1981? I can see that VAPE have a 100w DC system which is very good, and I have that on my 1982 maico 490 GS. But it's also expensive and a very heavy flywheel. Do you have a good tip?
    Or maybe a 6v CDI system if reliable and not too weak.

  • @fritzlannowack2701
    @fritzlannowack2701 3 роки тому +1

    Help what is the big Grey cilender connecting to the spark plug boot for and why will it not work

  • @robrobichaud7247
    @robrobichaud7247 7 місяців тому +1

    Need to see the full wire harness and all that goes with the kdx 80 1981

    • @2strokeguru
      @2strokeguru  7 місяців тому

      Best way buy the Clymer Manuel back of the book has wiring diagram

  • @gopipatre4987
    @gopipatre4987 3 роки тому +1

    M50 CDI working kese karta hai video banao magnetic coil starting coil per

  • @casalin1801
    @casalin1801 4 роки тому +5

    Omg you saved my ass. Could you do a simple wiring diagram for old kawasaki's? Only basic stuff

  • @theclubhouse1209
    @theclubhouse1209 4 роки тому +4

    Kevin, you should look into getting japanese industrial standard (JIS) screw drivers. I use vessel brand which seems to be top of the line for quality. I rebuild bikes and quads and they work for me. hope this helps. Great vid!

    • @2strokeguru
      @2strokeguru  4 роки тому +1

      I will check into that

    • @theclubhouse1209
      @theclubhouse1209 4 роки тому

      @@2strokeguru I got mine on ebay from a state side seller.

  • @waynebrown5428
    @waynebrown5428 3 роки тому +1

    Where can I find magneto and primary coil for 86 kd80? Very good info!

    • @2strokeguru
      @2strokeguru  3 роки тому

      They are hard to find because they don't go bad what happened to yours

    • @waynebrown5428
      @waynebrown5428 3 роки тому

      @@2strokeguru I picked up an old bike and the guy told me it needed points and condenser. I pulled mag off and magnets were broke and primary coil had several broken windings. Its in rough shape but I will save it.

    • @waynebrown5428
      @waynebrown5428 3 роки тому +1

      What engines have interchangable parts? I may look for donor bike or engine.

    • @2strokeguru
      @2strokeguru  3 роки тому

      @@waynebrown5428 kd80 kd100 mc1 ke100 km90 KM100 g3ss

    • @waynebrown5428
      @waynebrown5428 3 роки тому

      @@2strokeguru thanks

  • @darenverbonac5559
    @darenverbonac5559 3 роки тому +1

    Hey anyone still responding or have knowledge. He was mentioning the neutral safety switch with the black cap early in the video 7:00 min. If that wired was disconnected or cut, would that prevent a spark? Older bike Yamaha, 1979 175 Enduro.

    • @2strokeguru
      @2strokeguru  3 роки тому

      The neutral is only for the green light does not affect starting

  • @KiddKainMusic
    @KiddKainMusic 4 роки тому +1

    That grey ignition coil off the ke100 would that power the 1981 kdx175?

    • @2strokeguru
      @2strokeguru  4 роки тому

      Kdx175 i believe takes a different coil

  • @ScottSunn
    @ScottSunn 4 роки тому +1

    I ordered one of those orange coils... watching your other vid, doesn't sound like it is likely the coil is my problem, especially if you haven't seen one fail yet!

    • @2strokeguru
      @2strokeguru  4 роки тому

      replace points and condenser and spark plug even if it looks good

  • @YoungCEOsNY
    @YoungCEOsNY 3 роки тому +2

    Kevin you are the man ! Thank you

  • @joegreene777
    @joegreene777 5 років тому +4

    Solid information, thank you.

  • @edzezchuk6157
    @edzezchuk6157 3 місяці тому +1

    A have a 1979 ds 125 can i use a ts clymer repair manual for the engine i cant find any manuals for this bike thanks

    • @2strokeguru
      @2strokeguru  3 місяці тому

      @edzezchuk6157 yes climber is one that I use climber manual M369 Suzuki singles 1964-1981

  • @Best2Strokes
    @Best2Strokes 4 роки тому +3

    Very nice bro 😀

  • @aaronseay4903
    @aaronseay4903 2 роки тому +1

    Hey I had a question about the coil I've been searching all over for one can you tell me where I can find the coil.

    • @2strokeguru
      @2strokeguru  2 роки тому

      Ignition coil they don't go bad points and condenser that's what the problem is

  • @armandocarrillo6224
    @armandocarrillo6224 5 років тому +1

    Hello Kevin I have a 79 yz80D dirt bike that has no spark but will spark when i move the coil around on the head and place the spark plug on the head as you would to test for spark. The main problem is when i bolt the coil to the frame and try to check for spark i get none and the stator, which has points (no cdi ignition), is giving out no power I am super confused and I have purchased all new parts which is why I am confused why I am getting nothing to my plug.

    • @2strokeguru
      @2strokeguru  5 років тому

      Do you have Facebook friend request me we can chat on messenger we will fix it sounds like a bad contract

  • @edwerts7096
    @edwerts7096 2 роки тому +1

    I got a 87 kd80 that has no spark. It seems like nowere has the stator or the parts i need. What do you think i should do.

    • @2strokeguru
      @2strokeguru  2 роки тому

      Points and condenser is all you need

    • @edwerts7096
      @edwerts7096 2 роки тому +1

      @@2strokeguru Ok thank you! that don't sound to bad.

    • @2strokeguru
      @2strokeguru  2 роки тому

      @@edwerts7096 no part of a tune up parts from ke100 KM100 kd80 mc1 all use same points and condenser and never use used

    • @edwerts7096
      @edwerts7096 2 роки тому

      @@2strokeguru Thanks for the help!

    • @2strokeguru
      @2strokeguru  2 роки тому

      @@edwerts7096 very welcome

  • @kadin2356
    @kadin2356 4 роки тому +1

    If you have spark and everything else it needs to run but it still doesn’t run could still be an ignition or wiring problem?

    • @kadin2356
      @kadin2356 4 роки тому

      I still need to check compression but I just want to make sure it couldn’t be anything with the ignition. I got the bike with no spark and bought a stator. The stator fixed the no spark issue. I put gas in the bike and it started right up but then It stopped running. We rebuilt the carb which helped and it was running again. It stopped running and we noticed the spark plug threads were really worn out so we assumed we were losing compression We tapped out new threads and put in a threaded insert. That didn’t help it. So I’m not sure what to do next. We don’t have a compression gauge so we can’t see what it’s at yet

    • @kadin2356
      @kadin2356 4 роки тому

      It has a nice blue spark

  • @dylancrow7919
    @dylancrow7919 6 років тому +1

    Be sure your rope isn't small enough in diameter to get pinched between the ring and cylinder wall. I hate to sound like a dummy, but I didn't realize how much mass it took to stop the piston and when it turned over and I fed more rope in, it got pinched on the way back up.

    • @2strokeguru
      @2strokeguru  6 років тому

      when you put the rope in you dont have to put the piston all the way down its a good teck tip

  • @mckenzig1
    @mckenzig1 5 років тому +1

    Hi Kevin - I'm restoring a KE125 1976 - the magneto was shot so I ordered a 'new' one from ebay - only problem is this seems newer and has four wires instead of the orginal 5. I remember you have a video on mods to use the different mag but I can't find it now. Any pointers?

  • @inthelandofmilkandhoney457
    @inthelandofmilkandhoney457 2 роки тому +2

    Thanks Man 👍

  • @romuloparrilla1998
    @romuloparrilla1998 6 років тому +1

    HI KEVIN,I DO HAVE A 1979 KE100 AND STARTS EASY ON CHOKE BUT WHEN I SHUT THE CHOKE THEN IT WONT IDLE AND IT DIES ALL THE TIME.THANK YOU

    • @2strokeguru
      @2strokeguru  6 років тому

      romulo parrilla that’s a clogged pilot jet

    • @2strokeguru
      @2strokeguru  6 років тому

      watch my carb videos they will help you

  • @jenelyntomatcho6554
    @jenelyntomatcho6554 4 роки тому +2

    Which is more stronger sir,contact point or cdi.? thks

    • @2strokeguru
      @2strokeguru  4 роки тому

      Its a stronger than the other things CDI Offers smoother running engine better ignition at high rpm and maintenance free
      POINTS AND CONDENSER need replacement as part of a tune up at top rpm ignition brakes up and in between tune ups you will have to readjust points and at real low speed more likely to stall

  • @omegaman7241
    @omegaman7241 4 роки тому +2

    good video got any floats to sell?

  • @rileyallen2135
    @rileyallen2135 4 роки тому +1

    How would you suggest to convert a kd80 to a street legal bike? Is it possible to bolt lighting coils on my existing coil plate and wire in some sort of rectifier? I recently got a kd80 for practically free and your videos have been super helpful.

    • @2strokeguru
      @2strokeguru  4 роки тому

      you can easily make this bike street legal you will need lights ,stator ,and wiring harness ,horn brake light switchs frome a ke100

  • @nathantoubia6256
    @nathantoubia6256 5 років тому +1

    Hey Kevin I have a question for you, in order to get a spark I only need the thin wire coil that is grounded and has the lead that comes out and see soldered to the condenser along with two other wires one running to the points and the other exiting the stator that would then run to the ignition coil. Is that correct for spark or am I missing something?

    • @2strokeguru
      @2strokeguru  5 років тому +2

      There is the charge coil in back of the flywheel it's the coil with thin wire that connects to the condenser the black wire that goes to the ignition coil and a 3rd wire comming off the condenser to the points

    • @nathantoubia6256
      @nathantoubia6256 5 років тому +1

      @@2strokeguru as always I appreciate your wisdom!!! Thx

    • @2strokeguru
      @2strokeguru  5 років тому

      @@nathantoubia6256 very welcome

  • @bhallum1
    @bhallum1 3 роки тому +1

    What's the points gap on the kx80?

  • @JohnnyLee8355
    @JohnnyLee8355 5 років тому +2

    Well explained video👍👍

  • @hank1556
    @hank1556 6 років тому +1

    thanks! good info. Im restoring a 1979 KE125 at the moment

    • @2strokeguru
      @2strokeguru  6 років тому

      thatallredheadude 1 thanks I have a few ignition videos

  • @joshpaulson452
    @joshpaulson452 6 років тому +1

    So for rebuilding the top end can you give me a few specs for it?
    What’s the piston to cylinder clearance and how tight do all of the bolts have to be for the cylinder and cylinder head??

  • @framncesmaddox9042
    @framncesmaddox9042 5 років тому +2

    Thanks a lot I have been looking on the internet for weeks on how to wire up my points condenser and coil when I bought my kd80 all of the wiring was gone off of it so I didn't have no idea how it went back together

    • @2strokeguru
      @2strokeguru  5 років тому

      Awesome your welcome ke km kd mc1 all the basics same

    • @framncesmaddox9042
      @framncesmaddox9042 5 років тому

      When I got my kd80 all of the wiring was gone I had to rewire everything but I still can't get it to fire does it have to be grounded to the

  • @nathanupton5151
    @nathanupton5151 4 роки тому +1

    Where could I find a 1978 km100 ignition coil? Aftermarket or OEM doesn't matter to me.

    • @2strokeguru
      @2strokeguru  4 роки тому

      Ebay Kawasaki ke100 KM100 km90 mc1 all use same coil

    • @nathanupton5151
      @nathanupton5151 4 роки тому

      Kevin Bergeron rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F143428352056
      Would this work I bought one on eBay that didn’t work before?

  • @markdiveley8814
    @markdiveley8814 4 роки тому +1

    How come you never show how the wound wire coil is hooked up ? Behind the plate . I have to replace the wound coil. Someone before me tried to take the cover off with two screws and destroyed it. I need to now where all the wires go.

    • @markdiveley8814
      @markdiveley8814 4 роки тому

      Other than that great vido

    • @2strokeguru
      @2strokeguru  4 роки тому

      because there's no need to disassemble its i can put that in my next video as a request if that helps

  • @2strokeguru
    @2strokeguru  6 років тому +1

    You are welcome what kind of stuff are you looking for

    • @framncesmaddox9042
      @framncesmaddox9042 5 років тому

      Hey buddy I really really need some help I have a 1987 Kawasaki kd80 it is in real good shapeI bought it from one of my friends and needed a lot of parts on it but the whole wiring harness was took off of it when I got it so I bought the condenser and the points it already had a magneto on it but I don't know if I got everything hooked up right does it had to be grounded out somewhere inside of the crankcase please help me out

  • @mikemay7134
    @mikemay7134 5 років тому +1

    This is the most thorough ignition system video I have ever seen great job, now I have a 1981 Kawasaki KD 80 m that my dad bought for me and Christmas of 1980 I still have it engine is wore slap out I have a 2001 ke100 that came with an extra motor that runs with all the electronics can I put that motor in the kd80m the reason I haven't checked is my kd80 is wrapped up and put away in the back of the garage so before I pull it out I was curious will that motor direct bolt in would appreciate it if you could let me know save me the time of digging it out

    • @2strokeguru
      @2strokeguru  5 років тому

      Engine will bolt in how ever the exhaust is in the wrong place if you want to put a ke100 engine in the KD80M frame you will need a KM100 cylinder

    • @mikemay7134
      @mikemay7134 5 років тому

      @@2strokeguru I have a good friend that is a welder he actually did all the front rear end on my Jeep could we change the KD 80 Muffler an adapted at the front to fit the ke100 cylinder? I haven't really looked at it but since I found out now that it will bolt in I think I will try it because I've owned this motorcycle since it was brand new it was the first one that my father ever bought for me brand new

    • @mikemay7134
      @mikemay7134 5 років тому

      In other words I'm trying to keep the KD 80 exhaust as original as possible mine is the blue color is very rare and it is in excellent condition it's just that the engine is worn out so bad very hard to find parts for

    • @2strokeguru
      @2strokeguru  5 років тому

      @@mikemay7134 no parts are not bad to find great bike

    • @mikemay7134
      @mikemay7134 5 років тому

      @@2strokeguru I have been watching your videos for 2 days solid now I've never gotten so much education on these KDs and km's in my life I really appreciate it I talked to you about my KD 80 doing a 100 swap I've decided to change my mind and keep it the original kd80 engine although my engine isn't really rough condition crank bearings are bad everything on is worn out I read this bike for 7 years Non-Stop when I was a kid could you possibly build me a kd80m engine with the updated electronic ignition and sell it to me I would be willing to pay you

  • @FradyKatt
    @FradyKatt 4 роки тому +1

    I have a suzuki 125 2 cycle im putting on a cart. no fire new coil new points replaced stator plate.. 2 wires coming from engine black and yellow where do they go i have tried all I know i need help points set correctly all check good with ohm meter still no fire replaced flywheel no fire Im lost help Help

    • @2strokeguru
      @2strokeguru  4 роки тому

      Black is ignition yellow I don't know

    • @FradyKatt
      @FradyKatt 4 роки тому

      @@2strokeguru actually i got it to work by connecting both Blk and yellow. yellow wire come straight from coil out of engine and the blk comes from the condenser. ... Is there any difference between the lighting coil and the Stator coil they look the same.. Im just a dummy..

    • @2strokeguru
      @2strokeguru  4 роки тому

      Kool

  • @Sewer_surfin69
    @Sewer_surfin69 4 роки тому +1

    Would you recommend me replacing a coil? I have no secondary reading at all. What else out it be? Thank you

    • @2strokeguru
      @2strokeguru  4 роки тому

      I recommend points condenser and sparkplug

    • @Sewer_surfin69
      @Sewer_surfin69 4 роки тому

      @@2strokeguru Do you know the size for the flywheel puller? Didn't think there were that many sizes for it. You might have said it in the video but I cannot hear it. Thanks!

    • @2strokeguru
      @2strokeguru  4 роки тому +1

      @@Sewer_surfin69 Ebay ke100 magneto puller i believe it is 27mm

    • @Sewer_surfin69
      @Sewer_surfin69 4 роки тому

      @@2strokeguru would you mind helping me out? I changed out the condensor (waiting on new points to be delivered in a couple of days) but still spark. The mag looks like it's in rough shape with scratches on the inner wall. Can I send u pictures? Dont know if this can be a culprit

    • @2strokeguru
      @2strokeguru  4 роки тому

      @@Sewer_surfin69 1st i would change your points first set the gap then if not spark plan b 99.9 points are the problem

  • @mrj5174
    @mrj5174 3 роки тому

    What coil do you have and were do i find it i have an 80s Kawasaki kd80

  • @ananas1
    @ananas1 3 роки тому +1

    PERFECT BUT COULD YOU TALK A LITTLE BIT MORE ABOUT CDI IGNITION TYPE? AS YOU KNOW CONTACT BREAKER TYPE ARE OLD AND JUNK...

  • @countryboy5347
    @countryboy5347 3 роки тому

    Do you torque the inside or outside nut to 36 pounds

    • @2strokeguru
      @2strokeguru  3 роки тому

      There is no inside nut only outside

  • @rossmcintyre1759
    @rossmcintyre1759 4 роки тому +1

    Hi All,
    Kevin, as a new and proud owner of a classic bike, you have saved my butt many times too in a very short amount of time- your videos are fantastic- buuut....I need some help finding a rectifier for 1978 KE 100 - I can’t seem to find one- do you or anyone out there know a source to buy new
    Ross

  • @cb400fhonda6
    @cb400fhonda6 3 роки тому +2

    U r awesome

  • @tossandreelfishing8485
    @tossandreelfishing8485 6 років тому +1

    When I put my tester on where u said the needle doesn't even move I may need a digital tester

    • @2strokeguru
      @2strokeguru  6 років тому

      when you put the muli meter across the points you must disconnect the points first or it will not read

  • @cainbeeping8480
    @cainbeeping8480 3 роки тому +1

    Pretty cool. Where do you get that special tool?

    • @2strokeguru
      @2strokeguru  3 роки тому

      The impact driver?

    • @cainbeeping8480
      @cainbeeping8480 3 роки тому

      @@2strokeguru no got that the one that pulls the cover.

    • @2strokeguru
      @2strokeguru  3 роки тому

      @@cainbeeping8480 flywheel puller 15dollars on ebay

    • @cainbeeping8480
      @cainbeeping8480 3 роки тому

      @@2strokeguru thanks brother have a great day.

  • @tossandreelfishing8485
    @tossandreelfishing8485 6 років тому +1

    Do u know where to get the coil for the kd80?

    • @2strokeguru
      @2strokeguru  6 років тому

      toss and reel fishing the ignition coil

  • @TheJohnrob3
    @TheJohnrob3 2 роки тому +2

    Need Help understanding my MX 100 1974

    • @2strokeguru
      @2strokeguru  2 роки тому

      What is wrong

    • @TheJohnrob3
      @TheJohnrob3 2 роки тому

      @@2strokeguru Barn Find - Im not sure how to ; or where to connect the auto oiler cable. ... it work with the carburetor some how?

    • @TheJohnrob3
      @TheJohnrob3 2 роки тому

      FIGURE IT OUT

  • @tossandreelfishing8485
    @tossandreelfishing8485 6 років тому +1

    You are the man bro u are soo much help!

    • @2strokeguru
      @2strokeguru  6 років тому

      you are welcome happy to help

  • @ezpc3892
    @ezpc3892 3 роки тому +2

    thanks

  • @drivemechdiary5004
    @drivemechdiary5004 5 років тому +1

    sir,kindly feature kawasaki hd3 2stroke repairs,.thnx a lot.,

  • @jasonwilliams2852
    @jasonwilliams2852 5 років тому +2

    I cannot find the coil for the KD100 anywhere

    • @2strokeguru
      @2strokeguru  5 років тому

      Hard find because they never go 6volt coils I haven't seen a bad one on these bikes points and condenser and don't buy the Chinese version they are junk

    • @jasonwilliams2852
      @jasonwilliams2852 5 років тому

      @@2strokeguru mine is missing completely, most of the wiring is non existant but I got it cheap what do you think I ought to do?

    • @2strokeguru
      @2strokeguru  5 років тому

      I can't read the comment

    • @jasonwilliams2852
      @jasonwilliams2852 5 років тому +1

      @@2strokeguru oh sorry, my coil is missing and the wiring on bike stops after the motor only leaving the connectors for the cables to continue, I watched the whole thing on here but im still not sure of what everything is, also thank you for responding honestly I didnt think you would

    • @2strokeguru
      @2strokeguru  5 років тому

      @@jasonwilliams2852 so you need ignition coil

  • @t-murda7401
    @t-murda7401 6 років тому +1

    Where can i get a ke100 1986 magneto

  • @mastermoi
    @mastermoi 6 років тому +1

    Its not the same on a 1981 ke125? Mine is cylindrical... im confused i just bought the bike with a no spark condition. It has 2000km ( im canadian) so the points looks like new but my coil is connected to nothing but my spark plug i think the previous owner ripped it off without noticing it. Any ways i need to change it i dont know if its the right coil for it. Its pretty hacked up i beleive the guy who had it changed the whole plug wire with one extra long that looks like its comming from a car.

    • @2strokeguru
      @2strokeguru  6 років тому

      mastermoi some are different points wire black goes to ignition switch then to kill switch

    • @2strokeguru
      @2strokeguru  6 років тому

      mastermoi just because they look new they can still have ash on the points

    • @mastermoi
      @mastermoi 6 років тому

      Well, looks like i got myself a fully fonctionnal ke125 for 200$. The power wire to the coil was going nowhere. As soon as i plugged it I got spark

    • @2strokeguru
      @2strokeguru  6 років тому +1

      mastermoi awesome congrats

    • @mastermoi
      @mastermoi 6 років тому

      Kevin Bergeron hey man im back at it again with a no spark situation. I rode the bike for 7hrs and for the last 5minutes of riding the bike seemed less and less healty. I found out that the two yellow wires that goes to the voltage regulator melted on the exhaust. I tried welding them back together but still no spark. No that i look at your video i came to think that it might not even be my probleme because youre able to get some from only the black wire connected to the coil on your video am i correct? Now is it possible that those 2 melted wired made some kind of electrical short being in contact with the exhaust piping and mess something up? Sorry if my english is not perfect im french and thanks for making this video and taking the time to reply

  • @mrserious55
    @mrserious55 Рік тому +1

    first wire to coil second wire to kill switch

  • @joshpaulson452
    @joshpaulson452 6 років тому +1

    hey kevin it looks like my stator and or iginition is done. and both the stator and ignition systems are discontinued by kawasaki whats your reccomendation for what i should do.

    • @joshpaulson452
      @joshpaulson452 6 років тому

      this is for a 2000 ke100 may i add

    • @2strokeguru
      @2strokeguru  6 років тому

      Josue peterson send me your old parts

    • @joshpaulson452
      @joshpaulson452 6 років тому

      what for?

    • @2strokeguru
      @2strokeguru  6 років тому

      Josue peterson I have parts

    • @joshpaulson452
      @joshpaulson452 6 років тому

      I need an ignition coil for the 2000 ke100 thats the main peice i need. do you have that?

  • @mr.takuache5558
    @mr.takuache5558 7 років тому +1

    how can i send you a pictures of my promblem bc i need help with the wiring of a coil

    • @2strokeguru
      @2strokeguru  7 років тому

      the coil wire goes from the coil to the points and to the kill switch and key switch its a black with white stripe

    • @2strokeguru
      @2strokeguru  7 років тому

      you can email picks to Luggnutz76@yahoo.com

    • @2strokeguru
      @2strokeguru  7 років тому

      what bike do you have

  • @guiltygearcore
    @guiltygearcore 6 років тому +1

    Great vid sir. Im planning to revive my KE100. Do you know a store or website that sell OEM parts for the KE100?

    • @2strokeguru
      @2strokeguru  6 років тому

      just ebay i will be selling new and used parts in august

    • @2strokeguru
      @2strokeguru  6 років тому +1

      thanks i do my best

    • @guiltygearcore
      @guiltygearcore 6 років тому

      Kevin Bergeron great. Please let me know sir if you're about to sell .

    • @2strokeguru
      @2strokeguru  6 років тому

      Alca Bringer yes it will be in August there will be a video

    • @guiltygearcore
      @guiltygearcore 6 років тому

      Kevin Bergeron thank you sir.

  • @bashirhussain2115
    @bashirhussain2115 6 років тому +1

    Can a point system converted to cdi .?

    • @2strokeguru
      @2strokeguru  6 років тому +1

      yes i have videos on this topic you must watch the complete videos

    • @bashirhussain2115
      @bashirhussain2115 6 років тому

      Kevin Bergeron. thanks

    • @bashirhussain2115
      @bashirhussain2115 6 років тому

      Kevin Bergeron .please send video link

    • @2strokeguru
      @2strokeguru  6 років тому

      Bashir Hussain very welcome

  • @foisonpree
    @foisonpree 7 років тому +1

    Thanks for the informative videos Kevin! Recently picked up a 73 G4 trail boss, early style motor. Great information about the KE parts, exactly what I've been looking for, thank you! Are there any grounds needed for the motor to start? Doesn't seem so or maybe not seen in your video. Cleaned the frame before tinkering with the rest, so now I'm ready to see if it runs. Do I need to plug in the key switch? I'll get spark just from the coil wiring? Also, is the kill switch normally open or closed? Thank you for your time & knowledge 👍

    • @2strokeguru
      @2strokeguru  7 років тому

      Matt Lee most of videos cover trail boss 100

    • @2strokeguru
      @2strokeguru  7 років тому

      Matt Lee you are welcome

    • @foisonpree
      @foisonpree 7 років тому

      Kevin Bergeron great! confirmation on harness & adaptability between the years makes me happy. I was hoping Kawasaki would have used similar jigs & parts like they are known for.

    • @2strokeguru
      @2strokeguru  7 років тому

      Matt Lee some magneto are different but I will doing a on the difference and how to make new design work on the old one

    • @dylancrow7919
      @dylancrow7919 7 років тому

      Kevin Bergeron this is what I want to know. I want to weigh the option of trying to make my old system operational, or replacing the system.

  • @dylancrow7919
    @dylancrow7919 7 років тому +1

    Would you take a phone call? I'm doing my best trying to sort this out. MC1M. It was my fathers first dirt bike. I'm trying to restore it and I'm a small engine novice. Trying to get a good spark and diagnose this thing is difficult because I can't find a service manual for this bike. The best I got was a service manual for m series.

    • @2strokeguru
      @2strokeguru  7 років тому

      email me and i will give mynumber luggnutz76@yahoo.com

  • @tossandreelfishing8485
    @tossandreelfishing8485 6 років тому +1

    Yeah the ignition coil

    • @2strokeguru
      @2strokeguru  6 років тому

      have you tested the ignition coil the reason i ask i havent seen a bad on itsa 6 volt coil built to 12volt standards super strong points and condensor go all the time

  • @joshpaulson452
    @joshpaulson452 6 років тому +1

    Hey Kevin I went to a leaner jetting on my main jet. And now I’m getting a throaty sound at full throttle what does that mean?

    • @2strokeguru
      @2strokeguru  6 років тому

      What size jet did you use and why did you need to rejet

    • @joshpaulson452
      @joshpaulson452 6 років тому

      Kevin Bergeron I’m only able to get the bike up to 30mph and I was getting some oil residue outside the exhaust port from the engine and I decided to leaner.

    • @joshpaulson452
      @joshpaulson452 6 років тому

      I went from an 80 jet to a 75 jet. I live in Colorado at 6,300 feet altitude

    • @2strokeguru
      @2strokeguru  6 років тому

      peterson what I would do is put the factory jet back in it clean the the carburetor check the compression with a gauge and reset the timing

    • @joshpaulson452
      @joshpaulson452 6 років тому

      Kevin Bergeron how do I reset the timing on a CDI. And I was still going slow with the factory jets

  • @bradleyboltz8977
    @bradleyboltz8977 7 років тому +1

    Hey Kevin where can I buy the points and coils for the ke100

    • @2strokeguru
      @2strokeguru  7 років тому

      ebay sells new

    • @bradleyboltz8977
      @bradleyboltz8977 7 років тому

      What exactly are they called I know eBay has the breaker point and the condenser but what's the 3 coils called I think one is a charging/lighting coil and the other 2 are the 3v coils which I cannot find cause don't know what there calling them

    • @2strokeguru
      @2strokeguru  7 років тому

      the part you need points and condenser your coil should be fine its verry raar the coil will fail 6volt system

    • @bradleyboltz8977
      @bradleyboltz8977 7 років тому

      The coils are bad with broken windings like someone didn't know how to take the flywheel off

    • @2strokeguru
      @2strokeguru  7 років тому

      magneto thats the name of the part magneto

  • @jerichocruz1869
    @jerichocruz1869 6 років тому

    Sir Kevin, my HDX100 kawasaki and KE100 kawasaki are the same in the wiring? thanks in advance sir and nice video by the way

    • @2strokeguru
      @2strokeguru  6 років тому

      Jericho Cruz no they are different

  • @tossandreelfishing8485
    @tossandreelfishing8485 6 років тому +1

    OK thank you so much for the info u are awesome I'll let u know if I got anymore questions lol

    • @2strokeguru
      @2strokeguru  6 років тому

      you are welcome happy to help some times it takes awail for me to answer i normally get to anser questions after hours

  • @tossandreelfishing8485
    @tossandreelfishing8485 6 років тому +1

    So u think it's most likely points and condenser

    • @2strokeguru
      @2strokeguru  6 років тому

      yes the points and condensor 99.9%present i havent seen a bad coil

  • @naturechanel209
    @naturechanel209 4 роки тому +1

    There is a diffrence in Phillip's an jis

    • @2strokeguru
      @2strokeguru  4 роки тому

      Size of the screw driver used to fit the screw most screw are ph#3 on dirt bikers and 4wheelers

  • @mr.takuache5558
    @mr.takuache5558 7 років тому +1

    i need help

  • @carsonmiller9658
    @carsonmiller9658 5 років тому +4

    Has anyone ever told you that you sound like the waterboy?

    • @2strokeguru
      @2strokeguru  5 років тому

      Make fun I'm just trying to help people

  • @gopipatre4987
    @gopipatre4987 3 роки тому +1

    Language in Hindi me video banao

  • @brett9899
    @brett9899 4 роки тому +1

    Hi Kevin, have you got an email address i could have to send you an email? I have a question that I'm sure you can answer easily but may be a little long winded

    • @2strokeguru
      @2strokeguru  4 роки тому

      Are you in the USA

    • @brett9899
      @brett9899 4 роки тому

      @@2strokeguru the UK buddy. I have a g5 ke and just want to know what i need bare minimum to get it sparking. It came with no loom or killswitch

    • @2strokeguru
      @2strokeguru  4 роки тому +1

      @@brett9899 UK wow that's awesome clean or replace the points disconnect the main harness comming from the magneto jump the black wire from the magneto directly to the small black wire on the ignition coil

    • @brett9899
      @brett9899 4 роки тому +1

      @@2strokeguru I'll try it out! Thank you! Love the videos

    • @2strokeguru
      @2strokeguru  4 роки тому

      @@brett9899 welcome let me know how you make it

  • @alsuth803
    @alsuth803 5 років тому +1

    your information is good, but dude, i had to stop watching the video,. your camera is all over the place the whole video

    • @2strokeguru
      @2strokeguru  5 років тому

      Yes early video just getting started I am a professional mechanic not a camera man lol

  • @jeffnations6649
    @jeffnations6649 4 роки тому +1

    30 mins is not a quick video

  • @jayjohnson-sh9t
    @jayjohnson-sh9t Рік тому +1

    Good Job man😊