🤓HOW TO😮CLEAN BFS SPOOL BEARINGS!!!
Вставка
- Опубліковано 7 вер 2024
- Hey guys!
In this video, we’re going to learn how to flush your BFS spool bearings. This can be important as manufacturers often leave too much grease or oil in BFS spool bearings. A simple flush can help the stock bearings spin for much longer periods of time. Thanks as always for watching and cheers all!
Links to purchasing items(all links will be affiliate links and will generate a small commission for the channel. If you do use the link to make a purchase I am extremely grateful and the commission goes right back into the channel):
100ml Glass Storage Bottles(x2)(Affiliate link)
amzn.to/41tCorQ
ESD Ultra Fine Forceps Titanium(Affiliate link)
amzn.to/4asOsxF
Roro Bearing Puller(Affiliate link)
rorolure.com/p...
Roro Spool Pin Removal Advanced tool(Affiliate Link)
rorolure.com/p... pin
Roro Spool Pin Removal tool(Affiliate Link)
rorolure.com/p... pin
Roro bearing check tool(Affiliate Link)
rorolure.com/p... pin
#bfsfishing #baitfinessesystem #howto #arkrods #soloking #ifishband #haibo #fishing #seasir #shimano #budgetbfsfishing #darkwolfultra #tsurinoya #linnhue #budgetbfs #bass #bassfishing #trout #troutfishing #aliexpress #lews #abugarcia #fishingreviews #crappiefishing #kastking #shenghe #daiwa #ff01
Excellent. I would like to make a suggestion. With regard to the removal of the spool pin use the opposite end of the cross of the spool pin removal tool (the one without pin). This aligns always correctly until the pin is pressed flush with the axis. Then turn the cross and put the spool pin with the pin of the cross out of the spool axis. It‘s a two step process but it minimizes the risk bending the pin of the spool pin removal tool when you start pushing on the wrong end of the spool pin. In addition always use a soft bottom layer so that dropping parts don‘t bounce away. I learned it the hard way :)
Hey arne! Great pieces of information my friend! You are correct in that your procedure for using the spool pin removal tool is what is suggested by the manufacturer! I would also suggest and recommend using the method you use. The reason I use my method is because… I am lazy haha 😅😅😅 and I haven’t experienced a bent pin yet… but yes please follow arnes advice folks! As far as the soft bottom layer that you mentioned, that white may that my equipment is on is actually a watch makers work pad. It’s an interesting material that is soft and a bit shock absorbent. I have not yet had any issues with parts bouncing off and falling away. That being said, I think you are totally right to recommend working on a surface that will absorb the shock of a part dropping. Items like microfiber cloths, a thin towel or a thick cloth will work great for this application. Thanks so much for sharing these tips! Going to pin your comment for others to read and cheers my friend’
This is actually a timely upload. I was fooling sround with some bearings tonight.
Hey yep! Haha another member in the fb group had asked if there were videos out on this topic. I did a quick search and what I found was definitely related but a bit off topic and not quite BFS related. Hope the video helped you out! Cheers my friend!
Another great video mate.
Hey Adrian! Thanks so much! Hope the guide will help folks in the future! Cheers my friend!
Very well done video. Thank you for sharing your bearing flush procedure.
Hey Pacman! I hope the video helps you out in some way! Cheers my friend!
Excellent teaching video Pete.❤
Hey chris! My pleasure! Hopefully it will help folks out there without boring them too much haha 😅😅😅. Cheers my friend!
Thank you so much
Hey kaca! Thanks so much and cheers my friend!
Good tip Peter! I do It the same way as you. My tool for removing the pin has two sides, one is wider (and slightly cupped) to push the narrow side in more easily, and on the other side a pointed one that takes it all the way through.
Hey kalle! Yeap you are totally correct. You are meant to use the larger side to do most of the initial pressing and then swap to the smaller size once you get to the point where you need to press the pin through the spool shaft. I’ve developed a lazy habit of just using the smaller side to do everything haha 😅😅😅. Not a good habit to have lol. Thanks so much for sharing that tip and cheers my friend!
@@BFSFISHINGCHANNEL If it works, it works man! 😁🤗
Learned something new by the way, haven't let the shielded bearings sit for so long in the acetone, I'll do that next round. Like the air spray spray as well, I don't have access to compressed air myself so great stuff.
@@kallesjostrom6127 hey kalle! Hahaha yep I love that mantra but I’m also one for tinkering so… I’m a bit at odds with myself lol. As far as the SS bearings go yea I would let them soak for overnight or a couple days and agitate the container they are in from time to time to help get any dissolved grease out of them. Also, the canned air tip is a great one! I also don’t have an air compressor handy haha so air dusters come in very handy for helping to dry off bearings quickly but also get them spinning. Most likely, you won’t clear 100% of the grease inside the SS bearing unless you deshield them but using the canned air can help. Just be warned for solvent and grease to spray out lol 😅😅😅. Anywho, thanks for sharing your thoughts and insight kalle!!! Cheers my friend!
take out the seals is great for me and thanks for sharing, Mate!!!
Hey wirin! I also like to take out the seals to maximize the performance. I am not that big a fan of the sound afterwards though 😅😅😅. Cheers my friend!
Great video. Well worth watching
Hey Jeff! Appreciate the kind words and for you taking the time to leave such a great comment. Cheers my friend!
THAT BLUE CAP BOTTLE, YEEEAAAHH! I Know where you got that from 😂!
Excellent tutorial! Clear, concise, perfect :) !
He's the man, man, the dude, dude 0n0!
Hey Maurice! Hahaha I did not take it from where you think 😅. I no longer have access to labs lol. Amazon was where I procured this fine piece of glassware in all likeliness courtesy of China. Thanks so much as always for the kind words and cheers my friend!
@@BFSFISHINGCHANNEL ooh!
I made a test on a spare bearing I have from seasir, the orange one, even after 6h in acetone, the rubber was still ok.
I'm surprised!
Hey Maurice! Interesting! I wonder if different manufacturers use different materials for the colored coating 🤔. Thanks for sharing that info my friend and cheers!
Well Said I do virtually the same process, also if you don't have acetone lying around I find Lacquer thinner works well as it's "hot" stuff and Mineral Spirits to a lesser degree with the benefit of less vapors.😷😷😷😷😷
Hey Abel! Much appreciated for the other suggestions! My pops really likes using mineral spirits and denatured alcohol as well as solvents. Not sure which one works the best but I like that there are other options. Cheers my friend!
Good info Peter!!
Hey Troy! Glad to share info and knowledge with everyone as always =). Cheers my friend!
Thanks buddy😊
Hey Michael! This one is for you! Cheers my friend!
Please make a video on what type of grease and oil to use on reels. 😊
Hey Nick! Thanks so much for the request! I will definitely consider making a video along the lines of showing equipment I use and how I use them for maintenance in the future or maybe how to do a pretune or tune up on your reel? Will think it over a bit but am always open to suggestions on what can help folks the most. Thank you again for the recommendation and cheers my friend!
usually I am using kerosene on cleaning or flushing bearings much more efficient and cheaper than acetone, also best for rusted bearing when accidentally soak on salt water. 😅
Hey runo! Yep, you definitely can use kerosene for cleaning/flushing for sure. I believe kerosene actually leaves a light coating of oil after it flushes so it’s almost like a two in one. I am not sure it is readily available in the states anymore though as I have actually never used it. The reason I use acetone is because it leaves a clean slate so to speak and then I can come back in and use my low viscosity oil of choice to lubricate the bearing. Thanks so much for sharing your method and what it can be used on! Cheers my friend!
very useful video!!
Hey doc! Thanks so much for the kind words! Cheers my friend!
Very articulate, do you think some spool pins are perfectly cylindrical and the hole in the shaft is tapered? (Nerd question)
Hey yep! It’s definitely possible but I think it’s more likely that the pin is going to be the part that has the part that has a larger diameter that needs to be pressed in. I am not sure though and it’s just an educated guess haha. 😆 cheers my friend!
Since u suggested I could give you a thumbs down, I gave you one. Jk good video I do basically the same but I normally leave the bearings in the acetone for minimum 2 hours and shake the container pretty hard ever so often. If I think their is grease in the bearing I’ll leave them in over night or a couple of days
Hey tj! Hahaha totally fair! A thumbs down definitely helps me understand what folks like and don’t like so I do appreciate input regardless of the nature. As far as your 2 hour soak though I guess I’m a bit lazy haha 😆. I don’t notice too big a difference with ceramics in terms of soak time but what I do notice is if the acetone I’ve been using is pretty contaminated from multiple cleanings then the bearings I’m cleaning don’t spin as long… Def agree with the frequent agitation if doing a long soak though! Thanks for sharing your input and techniques and cheers my friend!
Good way to save money verse buying a new bearing.
Hey earl! I agree! Especially for stainless shielded bearings I think it really helps either their performance. It might sacrifice some longevity but it will free them up significantly! Thanks for sharing your thoughts and cheers my friend!
Bro what mic are are using?! Crisp
Hey Timothy! Haha thanks for the compliment! I am using a shure usb mic called the MV7. Hope that helps and cheers my friend!
I have Abu garcia vengeance bc and looking for shallow spool or bfs spool for this reel, do u know any?
Hey dawn! Hm… unfortunately I am not super familiar with that particular reel. I did do a search for a shallow spool and did not get any positive pings back. If you are willing to spend around $50 on a shallow spool I suggest maybe considering looking into purchasing a Soloking Acura pro at around $50-60 and just using that as a dedicated bfs reel. Hope that helps and cheers my friend!
I need to to the opposite for my TW80 and the Ray's studio shallow spool. Even at maximum setting, I can't have decent braking for lures around 6g. The spool is too light, the inductor cup, the same.
Hey Oscar! Hm that’s interesting. Rays studio spools come with micro hybrid ceramic bearings if I’m not mistaken? If that’s the case they’re not meant to be run with grease or lubrication. It might be that it’s a case of a poor matchup maybe… I’m not sure as I often don’t run into a case where the spool is too light and the bearings “too free” for a reel. How did you fix the issue out of curiosity? Also, is the spool meant for lure under 6g and not meant for lures over that weight? Cheers my friend!
@@BFSFISHINGCHANNEL its a bearingless spool.
Wow I don’t know that I’ve ever seen a bearing less spool before! I just looked up the stats on that spool and it’s supposed to be good for 1-15g so something is obviously not right… what do you think the issue might be? Cheers my friend!
@@BFSFISHINGCHANNEL mine never had any specification over lure weight. The problem is the spool is too much lighweight for the magforce system and/or the SV-like ramps inductor cup delay is too much. It's the first time i could not use the zero-adjust on magnetic brake reel. Gomexus says its spool is up to 5g lures, maybe to avoid problems like mine. I really doubt a SV-like spool with such a wide range of lure weight, if not being a sv-boost one.
Do hybrid ceramic bearings need oil? If so, which viscosity would you recommend? TIA
@@BGJ2121 Hey BG! Hybrid ceramic bearings actually do not require any sort of oil. They can be run dry and perform better when run as such. However, if you find the bearings to be too noisy or are running too fast you can add one or two small drops of oil to quiet them down a bit and to also slow them down. Hope that helps! Cheers my friend!
@@BFSFISHINGCHANNEL Thanks for the quick response. If noisy, would you still recommend TSI 321 for this type of bearing or something different?
@@BGJ2121 Hey BG! Totally! Tsi321 is supposed to be a great oil for bearings. If you don’t like the sound and don’t mind the bearings being a tiny bit slower then yes go ahead and use the oil. Cheers my friend!
@@BFSFISHINGCHANNEL awesome, that’s for your wonderful advice!
@@BGJ2121 hey bg! My pleasure! Cheers my friend!
Do they need to be dried off or will the acetone just gas off? Also what oil is best for this?
Hey seized! Acetone should just evaporate off quickly but it’s fun to use compressed air to see the rpms haha. If you have roro bfs st bearings just make sure to remove the orings before flushing and spinning them fast. As far as oils go, you don’t need oil for ceramic bearings. They can be run completely dry for SS bearings though you might consider TSI321 or Superlube oil. I’d recommend something like ISO32-ISO100 if you’re going with Superlube oil. The lower the number the lower viscosity it is and will need replacing more often. Hope that helps and cheers my friend!
@@BFSFISHINGCHANNEL wait the stock bearings don’t need oil at all? Also what is a good way to remove the C clip without damaging anything
@@seizedcarcass8440 hey seized! So there are two basic types of bearings and the need for lubrication depends on the type of bearing. In the video, I show the bearings with orange seals which are hybrid ceramic bearings. These bearings do not need lubrication at all. Stainless steel bearings though do require lubrication. As far as the c-clip goes the c-clip I removed in this video is specific to this spool. I am not sure other manufacturers use a c-clip and I think something like an o-ring would be a better solution and lighter. Let me know if that helps! Cheers my friend!
I can't remove the bearing from the spool shaft of my 22 aldebaran bfs, it won't go past the pin hole like its burred or something, nothing visible though.
Has anyone else had that problem?
Hey Darren! Yea that’s an unfortunate issue to be having and actually I did experience something similar iirc. I think I “solved” my issue simply by pulling the bearing off the shaft with quite a bit of force… not the most eloquent solution and it does run the risk of damaging your spool and the bearing but it somehow worked out for me. I’d suggest to look at your spool shaft and see if there might be any debris or manufacturing imperfections. If no then try giving it another go and see if it won’t budge. If you do see burrs on the spool pin hole then you’ll have to remove them somehow. I would advise against sanding or filing the opening though… you might be able to get away with using your fingernail or something hard yet softer than the spool shaft material to push the burrs down or move them to the side and help them fall off. In any case, I’m sorry I don’t have much better info than this for you. Hope it helps though and please let us know what you end up doing. PS if you do decide to acetone flush your bearings please remove the orings prior to using acetone. Cheers my friend!
Thanks very much for the great reply! I'l take your advice and have another go at it.
all the best. @@BFSFISHINGCHANNEL
@@darrenconway-hy8bx hey Darren! My pleasure! I wish I could offer more help in some way but I did experience the same issue and as much as it is a bit of a sledgehammer solution it’s the one that surprisingly worked for me haha. Let us know how things go! Cheers my friend!
AWESOME!
Hey ski! Thanks for the kind words and cheers my friend!