Replacing Rotors with Tapered Roller Bearings - EricTheCarGuy
Вставка
- Опубліковано 25 лип 2024
- Replacing Rotors with Tapered Roller Bearings - EricTheCarGuy
I thought I would try putting the website link first this time. I was very happy to make this video since I don't often see tapered roller bearings anymore. This video shows the step by step process of removing tapered roller bearings, cleaning them, and repacking them. I have thrown in a few tips and tricks that I hope will make the job easier and given you a list of tools that you will need to get this job done. I hope you have as much fun watching this video as I did making it.
You can visit me at the web address link at the top of this description.
---
Click below and Stay Dirty
Visit me at EricTheCarGuy.com
ericthecarguy.com/
Visit EricTheCarGuy Forum
www.ericthecarguy.com/forum/de...
Visit my Facebook Page:
/ ericthecarguy
---
Stay dirty
ETCG
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy. - Авто та транспорт
Thank you Eric. I love these old videos.
Your videos have helped , and inspired me over the years. It has been pivotal in changing the course of my life for the better!
Thanks Eric you saved my life….That little trick of removing the bearings was critical. Love your insights 👍
Bro,Ten years later &still the best vid on UA-cam
Eric, your videos are terrific. I'm the mom of a disabled (adult) child with health probs of my own. In my spare time, I started watching you a while back on my phone, computer, or ROKU. Since then, you've saved me I don't know how much trouble and money. Your concise yet thorough explanations and good use of a camera are very appreciated!
Seriously! Your trick to get the back bearing out was genius. Thank you.
@eurotrashcc Glad the video helped, thanks for the comment. This is actually one of my favorite videos.
@MrYahya1421 Now that I've been partnered I don't have to split them up into 10min segments anymore. It's nice because I've noticed that the first video gets more views than the rest. Thanks for your comment.
Thanks EricTheCarGuy, this video, like many others of yours have greatly helped and educated me! Just did my inner and outer front wheel tapered roller bearings on my '99 Mitsubishi Canter. It was daunting at first, to do a job I've never done before, not a mechanic but i'm eager to learn and do jobs myself.
@1Whatup8 Thank you for taking the time to leave such a great comment.
@Harrrri82 Glad you liked it, thanks for the comment.
@michaelovitch Thanks for the encouragement and the great comment.
@fliphighup If I'm honest this is one of my favorite videos. Thanks for your comment.
Thanks for this. I started to do brakes and rotor on a relative's GMC van today and was surprised to see a setup like this. I wasnt confident to proceed, but now I know what to do. Thanks for all the details and advice..
@shanemaura I'm happy to help, thanks for the comment.
Wanted to say thanks for making this video. I have a 94 Lebaron Conv that needed new bearings and I couldn’t figure out for the life of me, how to remove them from the hub assembly. I rented a press, posted on a bunch of forums, etc and no one explained it like you did. I followed your tips and they came out with almost no problems at all.
@asshatpolice I agree about the cotter pins, I did mention that replacement was the best option but I agree with you 100%. Thanks for the comment and your input. Sorry I got there first, you know you could always make the video and post it as a response to this one, or I could post mine to yours.
Just wanted to say thanks so much for the video. It was very informative and left me without any questions. I'm a new school car guy that is in love with his older GM. Felt stupid to ask this type of question on the forums.
This brings back memories of my dad teaching me this at about 12 years old. I have an '89 Trans Am GTA that's mine and I'm doing the same exact thing on. Thanks for the video and bringing back fond memories of my dad teaching me how to work on cars!
@shieldcracker Thanks for watching and subscribing I really appreciate it. I'm glad you like the video and that it was able to help, thanks for letting me know with this great comment.
@sheupel No, that seal replacement is a bit more involved. On a GM you would need to remove the cover on the diff to remove the 'c' clips that hold the axles in. The closest thing that I have for that is the video I did on changing the bearings on a Jeep, I think that video is listed under "Removing Pressed On Bearings".
Just had to rebuild all my brakes last weekend. 94 dodge ram. Havent had to do bearings in years. You never really forget it though. Love the videos. Keep it up.
Amazing video Eric. I've gotten a 1975 mustang 2 and I'm going to replace the rotors and drums(drums look original, maybe rotors too) and I've never done these kind of bearing or rotors before and this video is perfect for a first timer. It looks like these old style bearings are actually a million times easier to replace than newer ones.
I just watched the whole video as I do to most Eric the Car guy videos - I don’t even own a GM - but love learning something new! Such a wealth of info provided by Eric’s videos over the years ! We are very lucky.
@DieselCrawler86 Yep, I try to learn every chance I get. Glad you caught that because it was for you.
@Chris07860 This one is actually one of my favorites, thanks for your comment.
@MrCarlosCruz1 No you can NOT use lithium grease for this, normally you use axle grease. Good luck and thanks for the comment.
@ddut887 Thank you for that great comment. Now that I think about it your right, I should have used a clean set of gloves, I'll keep that in mind next time thanks.
@chechnya That is EXACTLY why I do this. Thanks for the comment.
Been watching for about 5 yrs. Doing my front brakes soon. You are the "Only one" of about 200 YT brake vids I've watched that explain which direction the grease seal goes. I have been known to not get it right. Great detail on this one.
Great video my man. You helped me to save $800 on two occasions now. Thanks for covering all the steps, (unlike the 100 other videos i've watched), in laymen's terms; as i was not so mechanically inclined in the whole fixing cars department. I've even been offering my family, assistance in my newfound expertise, all thanks to you. Best regards.
Heh, I just replaced the rotors on an '06 2WD Ford Ranger today. Same basic setup except the slide pins are not exposed. Glad to see that my procedure did not differ too much from yours.
@wardubo I try to be thorough if nothing else, I figure if I've never done this I want to see every step so that I can do it myself, I wish I had these videos when I started out, would have saved a lot of mistakes. Thanks for your comment.
Eric. Your videos Rock. Started watching your Channel just before you started the Fairmont project. I am a huge fan. Thank you for these videos. They have helped me many times.
@ITS4390 I'll keep that in mind. Thanks for the comment.
@ffgew22 I'm glad I was able to help, do what you feel comfortable with. Thanks for the update.
Great video. Saved me on my wife's 98 suburban at midnight on a workday. Keep it up, stay dirty.
@axenz1 It does appear that way, your comment makes me smile, thanks.
@fixinggrace Good call on the cheater bar. Funny thing, I had cut the scene where I said not to spin the bearing while cleaning it with compressed air for 2 reasons, first, I thought it sounded kind of "preachy", second I wanted to keep the video as close to 30 min as I could and that saved me 20 seconds. Great comment, thanks for watching.
I'm going to be doing this on a friend's Ford Ranger. I forgot to print the tightening procedure for the spindle nut at work so I'm just going to tighten it like you did. The torque specification was only a couple of inch pounds. I've never done these kind of brakes before. I've only done the kind where the rotor is sandwiched between the wheel and the hub assembly.
You never fail to crack me up, man. Like every 20 seconds or so. You must be from my planet.
@mrNHC Thanks for the great comment.
@13FravelJ The only time a rotor needs to be addressed is if there is a brake pulsation or damage to the rotor itself, many manufacturers recommend just replacing pads when brakes are needed if the criteria mentioned above are met.
@shrimp909 Thanks for the comment and letting me know.
Doing an assignment on tapered roller bearings and this helped a ton! Thanks for the video
Both my 1997 Ford F-150 and 2008 Ford E-350 uses these tapered bearings. Never dealt with these type of bearings before but you're video saved me lots of time and prevented mistakes! Thx!
@RAJSTA81 I will and thanks for the great comment.
Been scared to do bearings on my 91' S10 but this vid made it so easy! I wont hesitate to do it now! THANKS!!!
Gotta thank you again Eric. This worked on my 1995 Buick Roadmaster. Did both sides with little complications and I'm rolling again!
I LOVE THAT YOU TAKE THE TIME TO SHARE YOUR KNOWLEDGE WITH US!!! THAT IS SUPER COOL!!!! AND YOU DO IT SO WELL!!!THANK YOU!!!
@sheupel Sounds like you have a lot on your plate, I will do my best to help with the info but I don't think I'll be able to help with parts. Good luck in your endeavors, the world could use more people like you.
Eric, Thanks for THIS! It was an excellent video with super camera positioning for the viewer and extremely informative. I am doing the same on my '79 Trans Am and needed confirmation on a couple things. Sure is appreciated!
2k18 this is why i subscribed 5 years ago....keep it up eric and stay dirty
@RDIzzle109 Yea, I've seen that a few times, that dust cap is suppose to be there for a reason.
@spelunkerd These are by far my favorite comments, thank you.
what a great video. Eric's old videos are better. really informative and confidence inspiring! love it. thank you ETCG
@southernpride903 The lubrication of the slide pins and the brake pads helps a great deal to keep things quiet, the rest is up to the part. Perhaps you should recheck your work to make sure everything is correct just to be sure.
@southernpride903 I agree that you first need to find out what's loose. Watch the video I did on Axle Ball Joint Replacement, at the end I show how to check for play in the front suspension, this works for just about every make. Good luck.
Hello from 2019! Don’t mind me as I pull apart my 63 Galaxie disk conversion to correct some mistakes I now know I made.
Eric you got the best inspiration and lesson for us.Thank you very much indeed!
Great video !
Thanks for this great quality video and for your advices .
@Buchoass Didn't mean to interrupt your work but thanks for taking the time out to watch. As for pricing it's my policy not to go over pricing sorry, too much liability.
Thank you for the video,your tips helped me today repacking my wheel bearings which I never did before !Staying dirty with ya !
This vid merited me becoming a subscriber. I recently got a 1973 Ford F250. After its OE died, it sat in the garage for 10 years while his kids fought over it. Finally, the mother had had enough. She called the local garage and told the guy that if he picked it up that day, he could have it for free. It's a beautiful truck, but after replacing all rubber/gaskets, it needed brakes. Mechanic told me 1300 for pads, rotors/drums--you changed that plan! I did the whole system for less than 500. THX!!
@jgizzy Sorry to take up your time, you know I have no intention of taking the videos down anytime soon so you can always subscribe and come back when you have more time. I'm still giving you COTD for this. Thanks for the great comment.
Hey Eric just wanted to say thanks for the video, I just replaced the front rotors on my Blazer and without this video I would've had no idea whatsoever on how to do it but with your video I was able to get it done. This is my first car so I'm still learning, just once again thanks for all the great videos.
Only just found your channel ! Wow ! Excellent vid the way you shot it and explained everything was first class and i enjoyed the humour also. Very helpful video thanks for sharing.
dear etcg,
I've been watching every episode from beginning to end and I would like to say great job with the show. your videos are very detailed and easy to understand. :D
@RAJSTA81 I did just shoot a video of a timing belt replacement on a 99 Integra with a 1.8 DOHC but that won't work for you. I've gotten in the habit of recording every timing belt I do and should I come across the one you asked for I will let you know. Thanks for the comment, sorry I couldn't help more.
@pej0s Anti-seize compound that I use to lubricate where the brake pad comes into contact to keep things moving freely.
@nizmojoeblows I've done it lots of times when confronted with the same situation. The procedure is as follows: put a wrench on the brake line fitting on the caliper, have a buddy push down on the brake pedal, crack the line loose (put a pan under it) and when the fluid stops flowing close the fastener just like you would a bleeder, THEN have your buddy lift up off the pedal. Do it that way and you shouldn't get any air in the system.
@FaithfulAnnO I really appreciate you took the time to post this great comment, it made my day.
Hey Eric, thanks for the video, a couple little tricks that you showed saved the day.
Hi ERIC, I had just subscribed to your channel, and I can wait to start watching your new good stuff!! Because everything you do is good stuff.
Thanks Eric! Great video, I really appreciate your sense of humor. Your genuine passion for your work shines through in this video. I also appreciated the "improper tool usage" story. I am imagining your instructor scolding you multiple times for shortcutting and using the wrong tool. I look forward to torquing the bearings on my new-to-me 94 dodge wagon.
I thought I would just stop back and thank you for posting this video. I used your video to help with my son's 2001 ford ranger (front wheels), and your advice is gold. The audio is great, video is really well lit, and composition is outstanding.
I'm only new to this channel, I'm looking to start my trade soon as a Heavy Vehicle Mechanic in the army to pursue my interest in Auto mechanics. I'm already addicted to this channel! Loving it and will watch every video, Thank you Erik for teaching others! I think it's really great how easily you are making it to learn! Something I've always wanted to do. I wish I had the opportunity to have a Lecturer with your talent! Great channel hope you keep up the good work
@13FravelJ To be honest yes but it's purpose is just to keep the dust out, it really doesn't matter if it gets dented as long as it's sealed.
This video is the only video I could find that properly showed me how to swap my rotors out on my 1970 El Camino. Great video.
I can't tell you how much I love your vid! Thanks alot for posting em'
@LiveToBike9 In some ways it is a simpler design however the newer style with an integral bearing assembly is cheeper to manufacturer and maintain.
I remember doing this job on my 1981 Grand Prix. I wish I had this video back then, Great job Eric!
This video randomly popped up on my feed and I have to say I've never seen a bearing packing tool!!but I've also never looked for one either,pretty cool.
Wow your a real pro. Thanks for sharing your experience. Looks like my mechanic was telling me to use a C clamp. Not knowing it could damaged the master cylinder
When changing break pads.
Never would of thought it could damage the master cylinder. But it males sense And that the seals for break fluid only travels one way Thanks so much enjoyed your video I've subscribed
@Mulletsrokkify Glad you caught that reference, I was wondering if anyone would. Very cool. That does sound like a great topic for a video BTW.
@lasersdend15 Glad I could be a part of your education. Thanks for taking the time to let me know, it means a lot. Stay dirty.
Nice job Eric. Lots of good tips. Thank you
@chatingkicker Thank you, comments like this mean a lot.
thanks this vid helped me just got a 81 trans am i check out the fronts and the spindle nut was installed way to tight . this is my first car thats old
Great information always look forward to your videos I learn something new every time I watch much appreciated
Your are awersome! Been watching your channel for a long time. Your are helping me keep my 1996 chevy blazer going which now has over 341,000 miles on it! Thanks so much
Another great video! Watching your videos gives me confidence to do things myself.
@trekzilladmc Just a piece of old vacuum line, I don't know the size it just fits over the bleeder valve is how I sized it up.
Thanks Eric, this was a great video, about to do this job on my '98 S-10
yo Eric i just finished installing my new wheel bearing thanks to you ....i was installing new ball joints and when it was finally time to tighten the last nut which was the spindle nut i tightened it real good and when i got home from work i noticed my dust cap came off the washer with tooth in it was bent n the bearing was destroyed behind it....ooops!.....haha then i found your video which helped me put my new one on.....i got an 01 sonoma just like the one in this vid!.....you rule dude stay funny your vids r great and have a good one!
you just saved my life tonight! I've never done this kind of one piece and I have a 99 Sierra 2500 hd. beautiful stuff here sir! thanks!
Went through about 5 videos just to find your cool trick to removing the inner tapered roller bearing. Thanks!!
@GDISinc I'm glad to help but I don't see your questions here, sorry.
@wangbungal It may not say it but there are a lot of things missing from manuals that are a good idea and come from experience. If you use the fuel line on the vice grips or the tool that is made for crimping brake lines (there is one BTW) there should be no problem with the hose when your done.
I have a 79 toyota with the type of bearing. I didn't know how much grease i needed to use. So i fill up the whole cavity with grease. Now i know. Thank you, Eric.
This video may be ancient but the information is exactly what I needed to put together the bearings on my Studebaker. And it's incredibly well edited for being a 12 year old YT video. Thanks for posting his.