Installing a Mercruiser Trim Pump and Hoses -- '95 Crownline 5.7 Mercruiser Rebuild Part 16
Вставка
- Опубліковано 17 лип 2024
- In this video, I "fix" the rusty bracket that holds the trim pump the floor of the boat. It is very rusted and no longer held the pump to the floor. Also, I install the hoses that run to the trim rams. They enter through the bottom of the gimbal housing. There is a gasket to replace and the hoses have to be routed correctly. I hope you find this video helpful.
#Mercruiser #TrimPump #boatrepair - Авто та транспорт
But what you do to replace those hose’s????????
Asking they say they have to remove the engine bla bla bla they want charge me 600$ for it so how I can replace then any tips my worry is water leak inside
I don't think you need to remove the engine. Although, removing the engine isn't very difficult as you have seen. I would take that housing down, disconnect the hoses and then use one of the old hoses or a wire to pull the new hoses through the housing. Then just make sure you have a nice, new gasket to seal it up. The hoses just have threaded connections on their ends so they are easy to replace. Hope this helps and I can try to answer any questions you may have!!
@@605BOLT thaaaaaank you very much brother , one more question is better inside out or outside to inside
I would pull the old hoses from the inside to the outside with a wire attached to one of the hoses on the inside. Then disconnect the old hose from the wire and reattach a new hose then pull the new hose into place using the wire. It is easier get the hoses to go from the outside to the inside. If that makes sense. Haha. Sorry if that is confusing.
@@605BOLT hahaha perfect and thank you very much !!!!!!
Can't wait for startup! Been watching since the beginning and the suspense is killing me!!
Not too much longer!
Nice Lightning! Back in 99 my buddy asked me to jump his brand new Lightning over a sharp hill. Doing about 70mph I jumped it straight through an intersection about 3 feet in the air! Felt like I landed on a cloud, the suspension was amazing! I loved that truck I could slide it side to side and it was soo controllable. Man I would love find one for a decent price.
Haha wow! I've never jumped mine and don't plan to try! They're out there for bargains every now and then but a lot of them are trashed which is sad. ⚡
Great idea on the trim pump support! I may just do that also! I have mine mounted to a 2x4 to get it a bit higher up. I'll just make my support brackets higher! Get rid of that carpeting!
Oh man it's a rotted mess. Its not perfect but it will outlast the boat! 🤣
@FlyMeAirplane, what are you working on? Restoration? Repair? What boat?
@@605BOLT I have a 2002 190LS Stingray. I went through it 2 years ago and skipped the fairly rusted Trim Bracket. Due for bellows work next year! If you know Arduino at all I used one to make an engine monitor. Checks if engine is running, beeps if the engine is not running and the blower is off, oil P, Temp, volts, Trim position (beeps if engine off and trim too high)...
Haha nice. I actually do know a little. Enough to be dangerous.... Future video? 🤔 I appreciate you following along with these videos. Got curious so I had to ask.
Getting closer!
Yes definitely!
When you put the trim line hoses back on did u feed them both through at once or one at a time ? What's the best way to feed them through .got one back in having trouble getting the second through..any advice? Ty.
My engine was out of the boat at the time so it was much easier. Assuming yours is still in place, I would try to get a piece of wire threaded through in place first and then tape the hose to the wire and use the wire or string to pull the hose through. Might be kind of tough though. Sorry I can't offer more help!
I am having trouble replacing the trim fluid after some similar maintenance. I trim it all the way down, refill the tank, trim up, and repeat. My old mechanic told me to continue trimming for another two to three seconds after it reaches the limit to help push the air out, but I have done it many, many times and the piston still gurgles. Any advice?
Mine didn't give me any troubles so I can't offer any advice. It sounds like you're going the right way. I'm sorry.
What's that casing called that covers the trim pump line? It's almost granite like.
The part at 3:20?
They make a stainless bracket. Got mine online for around $50. Its same holes and bends.
I saw that. I didn't want to wait the few days on shipping or pay the money. Haha. This dang boat has cost me enough already!!🤣
Where did you get the trim line hoses and kit from?
I did not have to replace these lines on mine. I would call Ron at JR Marine and have him send you whatever you need. Do me a favor and mention that you saw the videos on my channel!!
@@605BOLT where is that located? Ty.
He is in Ohio. Ron is very knowledgeable if you just call him and describe what you need he will send you the latest and greatest. Some boat parts have updated versions and he always set me up right.
Website is jrmarine.com but I would advise calling.
@@605BOLT thank you very much!!