Hi, thanks for Your video! I have problems with digital clippings on the clean side.... Do You have this probs too? Or an idea how to reduce that? Thanks a lot
@@GeckoRC not that I remember noticing but I traded the pedal for something else. What’s your signal chain going to the Flamma? How hot are the pickups in your guitar? Single coils, humbucker?
one more question pls can you answer me aki even in the comment if this pre amplifier works for vocals--- if you connect the xrl on it and on the mic it works
There is no XRL input only one quarter inch input. However if you had an XRL to 1/4 inch converting transformer or another means of converting the XRL to 1/4 inch it would work then. Keep in mind it wasn’t made for vocals.
@@Warbyrds1 Good boss so I can buy the cable, I wanted to take my doubt if with this 1/4 cable connected to the microphone the preamp works normally, because its cost is very good and I already bought it, but I only see review in guitar tests, more I want to test it on the microphone
Yes I believe you would be able to do that. “Press the SAVE button and footswitch simultaneously to turn on/off the cabinet simulation. Press and hold the footswitch to change between the two modes.”
It might work great that way, but it is designed to replace your amps front end, not run through it (with cab sim off). Or go directly into a mixer (with cab sim on). Not really a distortion pedal replacement, but could be used that way.
It's been a year and now i have the same question. in my opinion mooer preamp offers good control by using the footswitches only, allowing u to change between presets with ur foot and u can load IR to mooer preamp. but this flamma fs06 offers good value at its price
Hi, thanks for Your video!
I have problems with digital clippings on the clean side....
Do You have this probs too? Or an idea how to reduce that?
Thanks a lot
@@GeckoRC not that I remember noticing but I traded the pedal for something else. What’s your signal chain going to the Flamma? How hot are the pickups in your guitar? Single coils, humbucker?
I face the same problem
Can I directly plug it in my 12 channel analog mixer, without using D.I Box ?
Yes, absolutely!
Chances are that you will experience some ground loop hum. If that's the case you will need to use a D.I. and lift the ground.
How much headroom
Does it have? How does it handle pedals placed in front of it?
It’s a good question. I gave that pedal away but if I get a chance to use it again, I’ll make a video with pre pedal effects into Flamma.
When i put fuzz. Its so bad
one more question pls can you answer me aki even in the comment if this pre amplifier works for vocals--- if you connect the xrl on it and on the mic it works
There is no XRL input only one quarter inch input. However if you had an XRL to 1/4 inch converting transformer or another means of converting the XRL to 1/4 inch it would work then. Keep in mind it wasn’t made for vocals.
@@Warbyrds1 Good boss so I can buy the cable, I wanted to take my doubt if with this 1/4 cable connected to the microphone the preamp works normally, because its cost is very good and I already bought it, but I only see review in guitar tests, more I want to test it on the microphone
Is this preamp loud???
It can drive an amp closer to breakup.
Hi, can I plug directly into the input of the ampli and use as a distortion pedal?
Yes I believe you would be able to do that. “Press the SAVE button and footswitch simultaneously to turn on/off the cabinet simulation. Press and hold the footswitch to change between the two modes.”
It might work great that way, but it is designed to replace your amps front end, not run through it (with cab sim off).
Or go directly into a mixer (with cab sim on).
Not really a distortion pedal replacement, but could be used that way.
@@Warbyrds1 or directly into the fx loop return? (bypass amp's preamp)
@@wazootube it’s a good question I don’t know I’ve never tried that
@@wazootubefor years I thought is what ore amps were for? That's what I do with my Moore's. With peddels between amp and cab.
Flamma Fs06 or Mooer preamp x2?
It's been a year and now i have the same question. in my opinion mooer preamp offers good control by using the footswitches only, allowing u to change between presets with ur foot and u can load IR to mooer preamp. but this flamma fs06 offers good value at its price
Showwww