Fixing Machine Problems- Tattoo University

[@TattooUniversity]

Just so everyone knows. I suggest that you spend the money to get better machines. These types of machines will always break in the middle of a tattoo. You never want to worry about your equipment during a tattoo. You want to focus on the artwork and the client. When you get frustrated with your equipment its difficult to tattoo. Its better if you can stay calm and enjoy yourself. I've had too many equipment failures during tattoo sessions. I always keep back up equipment but you shouldn't have to rely on that every day. Spend a little money to get good equipment. I do these videos as learning aids. I like messing with cheap equipment because it breaks. It gives me a chance to learn how to trouble shoot. It helps me learn what to look for in good machines. If you have cheap equipment I want to help you know how to keep it running. When you get a chance you should try to get equipment that won't fail you. You don't have to buy the most expensive machines. Just buy the ones that are built to last.

[@marksteele3026]

No one could have put this into a better perspective! I began with "cheap" machines, which eventually had minor issues that manifested into total breakdown. I purchased various "high quality" parts on the WEB, thinking that a rebuild would be simple and worth the effort and cash. I found myself sorely mistaken! The parts never would fit together, so I changed my tune, which brings this episode case in point for myself as well. I saved my money for a while, then opted for a mid-grade coil shader and liner. I was happier than a pig in poopoo man! So listen to this gentleman, he knows what's up for sure! Thank you sir!
~mark "tattoo" steele

[@jeremiahwhite6872]

What are some names of trusted tattoo machine home builders and how to contact them..??

[@sfinxwojerz]

Really good that you have mention a rear coil core gap and armature bar cause I have quite a bug one like more then one minimeter, I press a foot pedal and it won't start sometimes I have to press armature bar and it starts up I will try to reduce the gap by putting some shim washers I don't know how to spell shimwasher sorry. Thx for a vid you are great man.

[@TattooUniversity]

It is a pain dealing with a machine that hasn't been tuned correctly. Tattooing is a so much easier when machines run the way they are supposed to.

[@elshrapnel]

A lot of artists say that bent frames are shit, and I agree

[@DanielHernandez-iw2vw]

Hey, I’m pretty late tho this but my tatt machine is not working. The power bank Nd foot Pettle works fine. But the machine dosnt turn on. Any help?

[@evens14silvia24]

I have the same problem…. Did you figure it out?

[@black990ops]

You are the man! I can't believe how nice the machine became in the end when originally it were just a busted piece of metal lol thanks for the awesome videos as always!

[@TattooUniversity]

That is the beauty of machine tuning. Thanks for the comment.

[@timgibson1364]

They're still busted machines. The frame isn't bad but the coils, capacitor, springs are garbage and need replaced.

[@timgibson1364]

And don't ever put silicone on the coils. Lmfao

[@kennethmorris789]

i know u know your stuff, and i was just wondering, if you could do a quick video showing how to bend the springs and how much are how little to the specific machine, thank u and please i think i actually have mine tuned right but theres not one video on here that shows this process in detail, like doing the bending process a couple times up close to see where its setting over the coils.

[@TattooUniversity]

I've put some stuff out there but I'll try another video that will explain that

[@melaniedavis3626]

how do i fix my contact screw, passing the front spring? it’s not hitting it, but when i screw in the contact screw, it passes the spring. and i can’t get it to line up with it to run it.

[@justinspier3838]

looking straight down at the machine if you loosen the screw furthest from the contact screw you can adjust the amateur assembly on the horizontal axis rotating the front binding post where the contract screw is attached might help if the contact point you want is somewhere on the vertical axis

[@kennethmorris789]

i learned that we cant use the back springs for, the connection between coils, for frames, if u dont have the a yoke

[@SnakeBitesTattoo]

I enjoyed this video very educational thank you

[@sasadrazic6506]

mate i need your help... i got s similar coil machine like that but i cant set the way of the magnetic part above the coils... its maybe 2 mm space between then coil and the black metal thing wich means my way of the needle is about 2 mm max... how to get it on 3-4 without taking the lil metal plate

[@TattooUniversity]

I will have to see your machine. Can you email me at [e-mail]

[@melonmalone6307]

use washers

[@Blessed2SeeTomorrow]

can you or anyone please give me advice on my tattoo kit i bought there are sparks forming between the contact screw and front spring how can i fix this

[@TattooUniversity]

Some sparking is normal when it comes to the cheaper machines. Better springs and capacitor would get rid of the problem.

[@Blessed2SeeTomorrow]

@@TattooUniversity okay thank you because I'm so concerned about a fire starting or like something going seriously wrong this is all new to me and I'm very passionate about it I do not know everything but I put in the little bit of time that I can every so often being a new mom and everything is difficult to balance the two but I make it work when I can thanks for taking the time out your day to reply because I was so upset and disappointed I spent like well over $300+ on the tattoo kit and extra stuff just wanted to make sure I wasn't being ripped off

[@Blessed2SeeTomorrow]

@@TattooUniversity with your experience given my circumstances will it go away ? Or have you seen the problem get worse over time?

[@morganoliver5445]

It's not something that would go away without working on your machines. Watch one of his other videos about capacitors and how to change them. Very beneficial!

[@dinorocks7365]

Hi dude, what is the name for that set of steel measuring rulers you have, you know the gadjet you use when setting the gap between the armature bar?

[@rickcox1495]

Ive got an older danny fowler hand signed aluminum frame. Ive never gotten to even tune it because for some reason when u hit the switch to run it armature bar sticks down on front coil. Cant figure if coils are bad or what. Ive never had this happen and ive had ALOT of machines

[@morticiaandgomez725]

You have a wire touching somewhere. See if a coil wire is touching your yoke or if it is near a binding post.

[@kennethmorris789]

Ok thanks alot

[@timgibson1364]

Do a dollop do do a dollop of silicone. Lmfao

[@TattooUniversity]

I picked up the silicone from reading some older tattoo information. It isn't used as much any more. I swear by it though. It has helped me fix a lot of machines and keep them working. Probably use it more on the cheap machines with the bare wire sticking out of the bottom of the coil.

[@chinoching-topic]

Than you for the video

[@kennethmorris789]

Yeah I understand, but I be seeing alot of tattoo machines with the bumper on them , but ok I'll check for this ok, thanks alot

[@TattooUniversity]

You are correct. This is to make the machine quiet. You don't get the armature bar smacking the front core. This also prevents sticking. If the arm bar touches both cores it will stick for a second before it lets go.

[@gamingwithantz2529]

Question,my machine runs extremely softly,like there is no power coming through,no sparking either

[@TattooUniversity]

No sparking is good. No hit is usually not enough upward tension on your rear spring

[@TattooUniversity]

Sometimes it's the rear coil being to high and arm bar hits rear core. You want arm bar to hit front core and not touch rear core

[@rumble360]

He's sounds like bert from the big bang theory

[@dalewhitmore143]

Hi.
Do you know of a good place here in Australia to buy good machines for lining and shading?

[@TattooUniversity]

I would ask around on some of the social media sites. facebook.com/groups/857877664300304/

[@TattooUniversity]

I have the facebook page so people can post questions like that. I'm not from Australia so someone who is on there might be able to give you a better answer. facebook.com/groups/TattooUniversity/

[@dalewhitmore143]

Tattoo University Thanks.

[@TattooUniversity]

your welcome

[@presslikehitsubscribetoliv6437]

Hey I heard tattoome machines are the lick . They r made in Poland backed by alot of respected tattooists and have Operations in Australia. Really did the research with the geometry and these are one of a kind handbuilts. I know tattoome sounds cheap like a kit but it's Poland. Make pain tattoo machines are hand-built from Portugal and 150to 190 and very nice and run good I just got a super nice CNc J frame I mean both these companys will sell to a non shop and for a budget those r the way to go.. Also Paco Rollins, Chris gove are builders I also own machines from nice on the less costly side. My favorite machine karl hedgepath SC Sylvia collaboration mini Jenny super well built Karl hedgepath of jinxproof! also forward machines are cheap as is, look nice don't know how they run and have sales regularly

[@RaineR3313]

Hey i have a problem with my machine that i can't find solution online.
i have a rottary machine .While im using it ,everytime i stop the needle keeps staying in different height.Its very hard to tattoo when i can't settle my needle tip to begin at the same starting point. sometimes they stop fully out the grip sometimes they remain in.Its a new machine ,i just lubricated for the first time but the problem remains

[@TattooUniversity]

Some of the rotary machines have a spring that will return the needle to the correct position. If this spring isn't working that could be your issue. Maybe this machine isn't set up with something like that. What is happening is the cam is just not returning to the up position. There could also be an issue with too much tension on the needle. I would have to see it to know. Send a video to [e-mail]

[@2ndrunraidshadowlegends631]

A lot of rotary ( clone machines) don't have a returning spring. Best thing to do is pull the machine away from the skin still running. Or use a cartridge type grip with spring loaded cartridges

[@kennethmorris789]

Kenneth Morris.

[@kennethmorris789]

Hey gm I wanted to see if you would check out the tattoo machines I build and color coated. Let me know if you think they ok. I actually was motivated by your work. Look up if you can custom tattoo machines it's two 1min video ok. Please and thanks

[@TattooUniversity]

I'm having a hard time finding it. Can you send me a link?

[@kennethmorris789]

Tattoo University ok I think if you hit my k right in the comments section it should take you to them.

[@TattooUniversity]

Just be careful when painting the armature bars. I have a machine that came with a painted armature bar and I had to take the paint off. I also had to sand off the top of the cores because there was paint on there also. This got in the way of the machine functioning properly.

[@almightybones3335]

Right off the bat buy new machines lmao

[@TattooUniversity]

Just showing how to fix machines. I'm not using these. Just using for demonstration purposes.

[@thevideographer3991]

Hey man, i like your videos but you keep on repeating yourself. We know already the problem with the machine so get on with it, show us how to fix it