Good job at removing the studs but a little handheld Protane torch to heat the studs up a little bit would break the red Loctite lose and remove the studs easier, now here’s a suggestion when it comes time to put your chains on, jacked up your tractor high enough that your chains will go under the tires easily , it makes adjusting the chains so much easier than when the wheels are touching the ground
Good evening and thanks for the great tips Don! I did try the propane torch twice but it honestly did not seem to make much difference. Probably just me not doing it properly but will definitely try the chain method when I have to put them back on for the snow. Cheers and thanks again!
The “Gas wrench” is invaluable, heat is needed to release the locktite bond. I’m guessing based on the thickness of the bolt, and the hub acting as a heat sink, a standard propane plumbers torch won’t provide enough heat. Maybe the map gas providing a higher heat might work, but IMO every tractor and equipment owner should own a set of oxy-acetolyne torches. One of the last tools I’ve ever get rid of.
Cheers from Wisconsin! I wanted to thank you again for posting this video. I just watched AK dadstuff install his BORA spacers, and also saw your comments on them. I will be getting them for sure because of the easy way they install. What I love about this whole social media thing, is that we get raw information, and honest people as yourself, show not only the successes, but frustrations in some products and implements. If it weren't for you posting your struggles with your spacers, I'd be certain to be having the same struggles myself. I definitely thanked AKdadstuff for his posting, but I wanted to ESPECIALLY thank you for yours, and the headache I'll be able to avoid.
Good morning IHB! That's great! Thank you very much for the kind comments. And for the long time support. Have fun with the mod installation - and stay safe out there! Cheers!
Thanks for showing the procedure. It was quite a job! I have Talon Chains (Part# 12416AST) on my Kubota B3350SUHSD with filled AG tires. My dealer said I wouldn't need spacers for these chains, but I found there was NO way Talons would fit. So, I had to send the tractor back to the dealer for the $300 spacers. I do like having a wider wheel spacing for stability; always a good idea on a tractor. I have found, that for just moving snow on level ground with my bucket - I don't need chains. I imagine if you had a hill with ice, chains would be a must. Likewise for muddy ground.
Thanks nano! I find the same thing here . I am ok on reasonable level surfaces and even on small inclines or hills. But that big Steep hill gets me a few times very winter. LOL. But hopefully not this year. Thanks again and all the best!
Hey there GP!!! For a guy who says he doesn't know about being a mechanic you did a great job on this wheel spacer job!!! I like how you explained the steps. It shows you understand why you're doing what you're doing!!! The spacers are a good idea I'd say. The first winter I had chains on my tractor they caught on the treadle linkage. Bent it pretty good and it still isn't as good as it was but I managed to get it straightened out pretty good!!! Thanks for sharing this experience GP and take care!!!
Good evening and thanks Grampie! Quite a job for a guy like me I have to admit. I think I called Guy about a dozen times throughout. LOL. But all good. Done. And ready for old man winter. Thanks again and have a wonderful weekend!
Hey Gordon after watching this vidio of yours & many others over this subject matter--this is my take. This EXTREME amount of effort & wrenching just announced to the world that the "warrenty on my B2601 has just expired". I completely understand the issue of chain clearance. Where as other tractor owners do so for "enhanced stability"== DANGER, with the least concern of broken axle housing & VOIDED warrantys. My same "delema" was cured by installing a heavy baffle shield over the delicate components ( it was tappered & flaired preventing the occasional chain scrape). I think Kubota Realy wanted those wheel studs to STAY there for the reason to almost NEVER comming out --to do "After-market Rigging". Have seen " used epuipment" ( B2601 &2650's) with their axle collars repaced---no paint on them is the "dead ringer" sign. Thanks for the great Video Sir and happy safe tractoring.
Love all your videos GP. But I thought I would chime in for other viewer's. It has taken me 20+ years wrenching to get into my thick skull the value of heat. ALWAYS have a flame or even heat gun nearby when removing big bolts. Heat can not only do a lot of the work for you but can also save time and money preventing wrecking parts when removing torqued or seized bits. Heat applied correctly removes torque/compression in an of itself. Then use impact. Continuous offset torque (from breaker bar or wrench) deforms.
Enjoy the Trygg chains and the spacers. This is exactly what I did for my B2650 last winter. By the time I hit February the only choice was to use chains due to ice accumulation. The spacers in theory also help with stability around steeper inclines/declines. During the nadir of winter I still almost got stuck in a bad spot with the tryggs. But that was 100% operator fault! Your video is a good reminder to get the chains ready. I don't want to do the install in February when it is -15c and only 200 feet from the Atlantic ocean.
Thanks - I am looking forward to it Ron! Wow. Yup, I wouldn't want to be out in that weather doing it either. But I'll bet you have a pretty spectacular view. LOL. Stay safe and warm this winter. Cheers!
Good job as usual you have the right amount of mechanical knowledge for what you are doing and know how to research to do it right i would have done it a little differently with the same results but the trolls and safety clowns would have got me one tip when putting the tire back on put the tractor in neutral and spin the hub to line them up or put down some plastic with dish soap on it makes the tire slide easy good luck Ps I have been falling this and thought of a good bonus with the chains is they will brake up some of the ice as you work this winter thanks a gain
Good morning and thanks Dale! That's a great idea about spinning the hub- didn't even think of that. LOL. But would have been much easier. Thanks again and enjoy the weekend!
You’re more of a mechanic than you know. Good job. What I am surprised by is red loctite should be released by heat or it used to be. And you are right about rechecking torque because of painted surfaces on spacers. You impress me more every video by trying and learning new things. Most people’s limits are because they are afraid to ask questions when they don’t know. Keep up the good work. Cheers!
Thanks very much David! A few folks, including Guy, suggested the heat. I tried it on two of them but it didn't;t seem to help much. Guy figured it might be some other type of compound was used. Thanks again and I agree, you have to keep trying to learn new things. Cheers and have a wonderful weekend!
Thanks very much for this video Gord! I just installed wheel spacers on my L4060. The cram nut method worked like a charm. The hardest part was putting the loaded wheels back on. Did this on a beautiful 20 degree November day. Just waiting for my chains to arrive now.
As a mechanic of 38 years I will say you did a good job. With jobs like this, just take your time, be safe, and after it's done you will have gained some experience.
Good day and thanks very much! I appreciate it. Was a good learning for me and really happy it worked out. I checked the torque twice and it is holding so I will check it again next week. Thanks again and all the best!
Fantastic instructional video GP. I don't think you need all the disclaimers, I doubt a tractor dealer mechanic would have done it any better. I've been thinking of wheel spacers for a while for my Kioti to help with stability on the hills of my property, seeing you do it has given me the confidence to have a go. I'm sure I'll be watching this video a few more times. I reckon you'll have the right setup for the snow this year.
Good morning and thanks Mark! LOL. I put them in just in case. :) I have to admit, it was a challenge for me but happy it worked out and I agree- I think I am ready for the white stuff now. Have a great weekend and good luck with the Kioti! Cheers!
I just ordered wheel spacers for hill stability. Your video is extremely valuable giving me a good idea what I am facing. I am going with 3” spacers for the rear and 2” up front. Thanks for this informative video. And I agree with another comment, your mechanical skills are really very good. I felt bad for what you asked your small jack to do but it came thru.
Morning Greg! Good stuff. I am happy it was helpful. That little guy is rated for 4,000 lbs believe it or not, and the tractor weighs about 2,000 so I think it was ok. Good luck with the spacers and have a great weekend! Hope you are getting the sunshine and warmth we are here. Cheers!
I'm surprised that those studs were threaded into the hubs and not pressed in like their vehicular cousins. An excellent video GP and one that I am sure will benefit a lot of compact owners of all brands. You did good sir. Btw, you should swing by one of these days when I have to change one of the fluid filled 14.9-38's....LOL. It should take two men and a boy, but you know sometimes a guy has a trick or two up his sleeve. I continue to be impressed with your very succinct and professional way of delivering understandable information to the viewers !! Now a hamfisted backyard shade tree mechanic like myself would have stuck any old nut on the studs and welded them in place, then used an air impact to remove them. Like I say though: Don't do as I say and don't do as I do.....LOL Again, great video sir.
LOL! Well, one of the mechanics suggested I do the same thing but of course, that would require I had a welding machine and the air impact, and knew how to use them. LOL. But hey, you make do with what you got. Thanks T - mission accomplished! Have a good week my friend!
Thanks for another great video, I had success with the cram nut method. My B2301 studs battled me to the very last thread, I was a mechanic years ago, and never had a battle like that with Loctite or anything else for that matter - lol, I thought for sure that first one was cross threaded, but nope, every last one was like that. Then I hoped for the other side would be different - lol,, nope. Thanks again, lovethe videos
Great job GP, really did a great video too, now go play some for a couple days and check the torque a couple times and you’re ready. We had snow up in Amarillo last night according to the weather. We are to have a 50’s day tomorrow in East Texas so winter might sneak into our area this year? You all be safe up there and have some fun. Get Carol to start getting involved some, you can have cooking, or coffee breaks in your videos and walking into or out of your videos. Thanks for sharing with us. Hey Guy, how you doing? 👍
Thanks ODD! Lots to do this weekend here. I had flurries this last week here too so it's getting close. Will pass along to Guy. All the best to you and yours! Cheers!
I'm glad i watched this - I'm going to put chains on my B2601. A technique for putting a tire back on a rim. I'm no longer strong enough to sit on my butt and lift a tire into position. So I use a fulcrum and a lever. For a tire the size of the B2601 rear I'd (probably) use a 2x4 flat on the ground and parallel to the tire. Then get something for a lever - maybe another, longer, 2x4. Again, I'll have to try different sizes to get it right. The tire needs to be tilted a little in at the top I push down on the lever to balance the tire. Then you can move the tire without the weight a little left/right and the lever can be used to adjust height. I've done this myself on 3/4T truck tires. You may need someone to run the lever for a B2601 tire. But is sure beats lifting. Oh yes, BP is a Canadian - I should have typed Tyre...
Great video Gord . Have never seen anyone install spacers on the wheels before . I'm sure you have helped out quite a few people . You have a good Kubota dealer because he got you the parts . Al from Lummnah Acres needed parts for his mower and the dealer ( Kubota ) told him that he had to order the parts on-line himself . Talk about bad dealer service . Larkin looks like a great dealer to deal with . Let the snow fly . Gord is ready for it . LOL
LOL. Good morning Henry. Yes, Larkin is awesome. This happened on Friday afternoon. I called them and they had the parts ordered in and at the parts desk at 8:00 am Saturday morning. I though for sure I would be waiting with the tractor on jack stands for a few days. They are great. You bet! Let the white stuff come! Cheers and all the best Henry!
Good morning and thanks very much! Happy the cooler weather is coming your way. Getting very chilly here now so I was happy to get this done before the white stuff gets ere. Enjoy the rest of the weekend!
Very nice video and job well done. One of the nicest channels on UA-cam.. Thanks for your time and effort while making these viseos. Many blessings to you and yours.
Nice video. Looks like plenty of clearance for the chains now. Good job. They make a Stud removal replacement tool for about $20 U.S.. I have used one on several occasions. Thanks for sharing.
RED Loctite generally requires heat to break loose ( that is why you use BLUE if you expect to remove the studs ). This does not mean red hot - and try heating the stud only to avoid warping the flange. Good job using the tools at hand. I am glad none of them broke off. Cheers and take care
Great video! I’m considering a Kubota as my first tractor purchase soon, and your videos have been very helpful! I’ve been a professional mechanic for years, and as others have suggested I would recommend heat to loosen the loctite prior to removal.
A few ideas, heat studs ( it will break the lock tite bond ), add beet juce ( or some other non- corrosive liquid ) to all your tires for weight, stability and traction. Have fun, be safe !
GP, the strong part is the top jaw on an adjustable wrench. I noticed you were hammering on the bottom jaw of the wrench to get the studs out. You could break the adjustable wrench that way. I really enjoyed the video you produced as I want to get spacers for my B2601. You used 1 1/2 inch spacers I would like to use 2 inch but I don’t know how they will work with my 60 inch mid mount mower. I need to talk to my dealer. Thank you for the informative video! Wayne from Wisconsin
I think you are braver than I am. I'm not sure I would have tried that, but I did enjoy watching you do it. Thanks. Hi Guy, hope things are well with you and yours.
Good evening Sir, very well done GP !!! You are very good at showing and demonstrating safety practices and tools handling too !!! Like at told you before, you are mechanic !!! Keep up the good work and you too have a great TGIF !!! Cheers !!!
Great video coverage of a job really well done, Gord! I’m trying to imagine doing this myself on my L4060 with 14.9x24 loaded tires LOL, I believe there is over 400 lb of liquid ballast alone, not even including the weight of the the tire and rim... not something you’d want to fall over! A few years ago, my brother helped me replace the brake pads on my old Massey 50 (12x28 loaded tires), and even with two of us it was a hair-raising job. I’m not getting any younger so probably a job for my dealer should I ever need to do this. By the way, I concur with one of the other comments that with care and patience, some heat, even from a household propane torch, can be quite effective at breaking down locktite - even the “permanent” stuff. Nevertheless, a few well chosen tools and strong arms can also do the job, as you well demonstrated! Cheers!
Good morning Dave! LOL. I concur. Not sure I would want to try taking those off either. :)) I tried the propane torch on a couple of them but not sure it really helped at all, but then again I may have done it incorrectly. Have a great weekend!
Looks like a good job to me and I know this is a bit late but for the future I'll share a thought. First as others have said bit of heat makes it much easier to get those studs out and second if you're replacing them with new I have found that welding the nut to the old stud makes short work of getting them out. I know, "now you tell me" any way you got it now. Thanks for sharing and good luck with the snow!
LOL. - Never too late for good advice Rick. And always appreciated. You never know - I may need that advice for something else that cosalong one day. Thanks again and all the best! Cheers!
Wow... you did well. That was very enlightening. I am really surprised that given the way the studs are secured to the hub that Kubota would use spacers that need new longer studs. With a lot of spacers on the market, the spacers will bolt to the hub using the original studs and nuts and then the spacers themselves will have a second set of studs for attaching the wheel. Along with plenty of clearance for the chains you should have improved stability on side slopes.
Good day and thanks Joe! Me too. I had seen another aftermarket type that was designed as you suggested so I assumed the Kubota ones would be similar. I'm all ready now for the winter! Cheers and thanks again!
G P a lot of work goes into something that looks like a easy job reminds me when I started building Manitowoc Cranes the were all hand built but as you said gives you pleasure when done God Bless PaK
Very good mod for your tractor. As for the original Kubota lug nuts I have found them to be of low quality. The metal is soft and the walls are thin. I always replace them with better quality nuts on any tractor I own.
Nice work and great video Gord! Very instructional. If you ever have to - I hope not - remove the wheels and put back on again, grab ya some 3ft bars, pipes, even old tool handles like axe handles and put on either side of wheel/tire and use leverage to help lift up and manuver wheel/tire back in alignment and up in place... Save that back my man. Hope your family has a wonderful weekend.👍☺
Great job. What a pain in the neck getting those wheel studs off! Little snow here in central VA, so I shouldn't have to worry about chains, but still a good watch to add to the mental catalog. Thanks!
I just put 3" spacers on my L3901 and I did not remove the wheel studs. They fit perfectly on existing studs and came with the hardware needed to attach the wheel. Also, I have a dolly made with 2x4 and 2x6 which I slid right underneath the tired. I then strapped the tire on to the dolly and never had to lift or roll the tire during the whole process. Just move it out of the way.
wow, that was a hard enough job without having all the extra work of explaining every step and keeping the cameras rolling. thanks for taking the time. great video.
Glad I don't have to deal with chains and snow, just earthquakes, fires, etc. lol. Your rear tires looks like the same size as my L2501. Mine are filled too and I'd hate to have to change one. My JD 4320 are filled also and weigh around 4-500lbs. The only thing I've heard that's an issue with extending front/rear wheels out, is the possibility of axle/bearing damage due to excessive weight on the end of the axles. Those wheel extenders don't extend the wheels out far enough to be a concern tho. I've seen tires extended out 12+ inches and that's an issue, especially with loaders and heavy 3pt loads. Have a great weekend. Cheers my friend.
Good morning Tim! LOL. Thanks for the good info about the width of the extension. I had read the same thing and found an aftermarket type but they were 3" spacers and so I thought it was best to go with the Kubota spacers since I know they would be specifically designed for my tractor. They are only 1 3/8" inches wide. I am happy I did now, as several folks have said the same thing you have. Hope all is going great! Cheers!
@@GPOutdoors I don't know if you get the US news up there, but north of me there is over 140k people under evacuation orders this AM (10/27) and around 2.2M people without power due to PG&E power shutoff. I can see a fire over in the west hills on my NW tower cam. The Kincaide fire really took off early this AM due to wind gusts of up to 80mph in the Napa/Santa Rosa areas. 2 Old wineries have already burned. I have a friend who has property in Lake County and I don't know if that area is under evacuation or not. I assume it is. I have wind gusts on my commercial weather station of 28.8 mph so far. This is supposed to last thru Sunday eve up to Monday 1100. Some of the areas that burned in the Tubb fire of 2017 are part of the evacuation order. Not looking good so far. The way Calif is going, I mite have to move to Canada, lol. Have a great day Gord. Cheers from Tim in SF Bay Area.
hey thanks for telling me Tim. My daughter is in LA currently but hopefully ok. Unfortunately I don't have TV or any reasonable news up at the cabin so while I am here, I have to rely on Guy or Bob to fill me in on things. So I had not heard. Hope for the best for everyone. wow. thanks again. Cheers!
Another great video GP!! I really enjoyed watching! You were very detailed and you covered all the bases! You made a pretty tough job look easy! lol I like the clearance you have now for them chains. Have a great weekend GP!!
Hi Gord! Man, that looked like a pain to do but well done. This was a very good instructional video for a non-instructional video! LOL. You clearly did you homework ahead of time. Thanks for sharing!
LOL. Thanks Charles! Yes, I think I messed up the terminology perhaps. A "Jam Nut" is, up here, an actually specifically engineered nut used for this same purpose but it is designed and built to be the nut you put behind the main nut. I think "Cram" nut is kind of slang for when we just use two nuts and tighten them together. LOL. In my case, I didn't;t purchase a Jam nut - I just used two of the wheel nuts together. Perhaps If I had though, maybe I would not have cross thread all the nuts. Thanks! And enjoy the weekend! Hoping for a little sunshine up here. :))
Good job. FYI if you put a little heat to the studs from a little propane torch you would have simplified your job. Locktite is actually a plastic sealant and heat melts it. You could have almost taken them out with your fingers. They would have gone back in easier too with that little heat. I was a mechanic by trade...
Hey good day and thanks Richard. I tried the torch on two of them but it didn't seem to help any. Guy suggested they may have used a different compound ( or i was applying it incorrectly). But wish it had worked. LOL. Thanks again and all the best!
Very informative video! I originally added spacers for stability. Nice to know they will help with chains in the future on my BX! I'm sure those loaded tires were a hand full to move around!
wow! thats some work gp! i never would have thought those studs was threded on the hub side. though they would be like cars with the ribs on one end and threads on the other side. well you learn something new everyday.
Let me give you a tip when you use the nut trick to take off the tire bolts put the lug nuts on against each other grab two wrenches for the front one and one for the back one what's your going do is lock them together as you tighten the back one go loosen on the front one till tight now they are locked to take off the wheel bolt use only the front nut to take it off the back nut going keep the front one from turning and make sure you use the right wrench that fix the nut a loose one will round it off
Good job GP.......now thats prolly the best video out there on this particular job......lots of good info for sure.....thanx for posting my friend and have a good week....... :)
Good job GP a couple of suggestions. A little heat goes a long way on loctite. A propane torch is more than enough. Also please don't hammer on adjustable wrenches. The jam nut method you want to tighten them against each other with two wrenches to jam them against each other then use the inside nut to loosen the stud. There is also a stud remover tool made for the job.
Hey good morning and thanks for the suggestions James. I appreciate it. I did try the propane torch on two of them but it didn't seem to help much (but I may have been applying it incorrectly). Agree - didn't want to hammer on them but they just would not budge at all. I had a length of pipe as well to try to get leverage but there is little room under that fender to use it. I had called two parts places in nearby towns but neither of them carried the stud remover. I think that would have been ideal for sure. Thanks again for the helpful advice. Always appreciated. Enjoy the weekend!
glad to see you did not run it very long before putting the spacers on only seen two things missing a picture of guy and a cheater bar for the pipe wrench and a propane torch for the studs okay that's three things. also Paul short also o&d life UA-cam channels had to put there spacers on
LOL Bob! Well, let me be honest. I think I called Guy about 10 times throughout the project. I attempted using the propane torch but it had minimal positive effect ( Guy's suggestion), and he gave me a cheater pipe but I didn't need it. LOL. OK, you got me! Cheers and thanks for the comment and for watching! I think you and Guy would get along quite well. LOL. Cheers!
Nice vid GP! If you ever have to take the wheel off again, I’d suggest you get yourself a long breaker bar, and your foot to do the wedge method and you’ll get you tire back on just like you do a car. Look up changing a semi truck tire. Much easier but great vid
Nice job, GP. The job never is as easy as it appears when someone else does it, right? Excellent walk-through and you'll be set for those chains. I'm glad you decided on the spacers b/c of those chains. I was wondering what size spacers you were going to install. The spacers appeared to give you a nice amount of room to allow for chain play. Enjoyed a full-watch. See you on your next video.
LOL Houndsman! So true. I remember telling Guy the "simple" steps I would go through to get it done. And then I called him about a dozen times while I was doing it. LOL. Sure seemed simple when I was planning it. Have a great weekend and thanks!
When you are dealing with heavy tires use a long bar and slide it under the tire, perpendicular to it. It makes it a lot easier to get it lined up. I use one 3-4 feet long.
I think you also gave yourself a bit more stability with the spacers by widening your stance, should prove beneficial on uneven ground and with heavier loads.
Once its cured, thread locker can be "softened" into compliance with mild heat. Soaking the hub with a heat gun before you start would make it a world easier. A torch would work too but then the paint gets cooked-off and you risk damaging the axle seal.
Looks like a lot of work on the wheel spacers. I took the easy way and used Bro-Tek wheel spacers that just bolt in to the existing studs, and then have bolts/studs that attach the wheels to the spacer. Easier, but now I will have to remove the wheels every so often to check the torque on the studs holding the spacers on to the tractor. Easy now, harder later..... Cheers!
Good morning Jim. It sure would have been much better for me. I called 2 automotive places in nearby towns and the one rental place and no one had one. But wish I could have found one. I think it would have been much easier for me. Thanks for watching and enjoy the rest of the weekend!
Being from Caseville in the thumb where it's flat I appreciate the need for a wider foot print. I know the landscape of the U.P. . Our daughter went to northern, go cats, and getting a tractor back on it's feet doesn't need to happen when you can prevent it. Thanks for the info. My B2620 may get the same. Keep the greasy side down.
Well done. Note for everyone. I worked 40 years on my knees and it wasn't until I retired and moved up and bought a kubota that I found the perfect knee pads. I was using them I somehow had but didn't know I had and I couldn't believe how perfect they were. They do not hurt and I put them on every time I go outside to work even if I don't feel I need to kneel. I end up coming into the house with them on because I forgot I have them on. I found the online at HD. They are Tommyco brand. The 1" foam with 1 strap. Less then $5 American!! I have about 12 pairs in different areas and have even away about a dozen pari to friends who I see abusing their knees. No replacement knees for me!! They don't stock them. Tommyco T-Foam Light Duty Kneepads $4.92 pr. Don't let Light Duty fool u!! Best ever!!!!
Again...good job cheif! I always wanted to know how much it would take to get the job done. I wasn't a believer in chains for my 2650 but this last storm of 30 cm. Of wet snow made me reconsider!😎 keep an eye on the tree line for you know what!!!
i was more or less getting at the studs are they right hand threaded on the hub and im sure thier threaded on the lug nut side. but on vehicels you just pull them thru lug nut hole. anyway cheers and have a great day gp!
Yes good day Dale. A few folks mentioned that about vehicles ( cars). These are threaded into the hub. They go in clockwise and come out counterclockwise. And not sure but I am pretty sure the threads are interference threads because they are difficult all the way through when removing or putting them in. I hope that answered your question (?). Cheers!
@@GPOutdoors yep thank you sir. interesting. and okay we have those kind of threads at my workplace. great for saftey! those kind are way more difficult to work thier way loose. ok have a good one bud!
You've got a great style of clear, patient, and logical. Great job!
Thanks so much Frank!
Good job at removing the studs but a little handheld Protane torch to heat the studs up a little bit would break the red Loctite lose and remove the studs easier, now here’s a suggestion when it comes time to put your chains on, jacked up your tractor high enough that your chains will go under the tires easily , it makes adjusting the chains so much easier than when the wheels are touching the ground
Good evening and thanks for the great tips Don! I did try the propane torch twice but it honestly did not seem to make much difference. Probably just me not doing it properly but will definitely try the chain method when I have to put them back on for the snow. Cheers and thanks again!
The “Gas wrench” is invaluable, heat is needed to release the locktite bond. I’m guessing based on the thickness of the bolt, and the hub acting as a heat sink, a standard propane plumbers torch won’t provide enough heat. Maybe the map gas providing a higher heat might work, but IMO every tractor and equipment owner should own a set of oxy-acetolyne torches. One of the last tools I’ve ever get rid of.
Cheers from Wisconsin! I wanted to thank you again for posting this video. I just watched AK dadstuff install his BORA spacers, and also saw your comments on them. I will be getting them for sure because of the easy way they install. What I love about this whole social media thing, is that we get raw information, and honest people as yourself, show not only the successes, but frustrations in some products and implements. If it weren't for you posting your struggles with your spacers, I'd be certain to be having the same struggles myself. I definitely thanked AKdadstuff for his posting, but I wanted to ESPECIALLY thank you for yours, and the headache I'll be able to avoid.
Good morning IHB! That's great! Thank you very much for the kind comments. And for the long time support. Have fun with the mod installation - and stay safe out there! Cheers!
Thanks for showing the procedure. It was quite a job!
I have Talon Chains (Part# 12416AST) on my Kubota B3350SUHSD with filled AG tires. My dealer said I wouldn't need spacers for these chains, but I found there was NO way Talons would fit. So, I had to send the tractor back to the dealer for the $300 spacers. I do like having a wider wheel spacing for stability; always a good idea on a tractor.
I have found, that for just moving snow on level ground with my bucket - I don't need chains. I imagine if you had a hill with ice, chains would be a must. Likewise for muddy ground.
Thanks nano! I find the same thing here . I am ok on reasonable level surfaces and even on small inclines or hills. But that big Steep hill gets me a few times very winter. LOL. But hopefully not this year. Thanks again and all the best!
I think you're more mechanical than you give yourself credit for ;)
Thanks very kindly Ed. Had a lot to learn before trying this one. Thanks again and enjoy the weekend! Cheers!
:) - Just what I was thinking, 10/10 for taking the job on and not wimping out when it got a bit tasty.
Hey there GP!!! For a guy who says he doesn't know about being a mechanic you did a great job on this wheel spacer job!!! I like how you explained the steps. It shows you understand why you're doing what you're doing!!! The spacers are a good idea I'd say. The first winter I had chains on my tractor they caught on the treadle linkage. Bent it pretty good and it still isn't as good as it was but I managed to get it straightened out pretty good!!! Thanks for sharing this experience GP and take care!!!
Good evening and thanks Grampie! Quite a job for a guy like me I have to admit. I think I called Guy about a dozen times throughout. LOL. But all good. Done. And ready for old man winter. Thanks again and have a wonderful weekend!
Hey Gordon after watching this vidio of yours & many others over this subject matter--this is my take. This EXTREME amount of effort & wrenching just announced to the world that the "warrenty on my B2601 has just expired". I completely understand the issue of chain clearance. Where as other tractor owners do so for "enhanced stability"== DANGER, with the least concern of broken axle housing & VOIDED warrantys. My same "delema" was cured by installing a heavy baffle shield over the delicate components ( it was tappered & flaired preventing the occasional chain scrape). I think Kubota Realy wanted those wheel studs to STAY there for the reason to almost NEVER comming out --to do "After-market Rigging". Have seen " used epuipment" ( B2601 &2650's) with their axle collars repaced---no paint on them is the "dead ringer" sign. Thanks for the great Video Sir and happy safe tractoring.
Love all your videos GP. But I thought I would chime in for other viewer's. It has taken me 20+ years wrenching to get into my thick skull the value of heat. ALWAYS have a flame or even heat gun nearby when removing big bolts. Heat can not only do a lot of the work for you but can also save time and money preventing wrecking parts when removing torqued or seized bits. Heat applied correctly removes torque/compression in an of itself. Then use impact. Continuous offset torque (from breaker bar or wrench) deforms.
Wow! Much more involved than I thought it would be. Thanks for sharing.
You're very welcome Stephen. Surprised me as well. Have a good one!
Enjoy the Trygg chains and the spacers. This is exactly what I did for my B2650 last winter. By the time I hit February the only choice was to use chains due to ice accumulation. The spacers in theory also help with stability around steeper inclines/declines. During the nadir of winter I still almost got stuck in a bad spot with the tryggs. But that was 100% operator fault! Your video is a good reminder to get the chains ready. I don't want to do the install in February when it is -15c and only 200 feet from the Atlantic ocean.
Thanks - I am looking forward to it Ron! Wow. Yup, I wouldn't want to be out in that weather doing it either. But I'll bet you have a pretty spectacular view. LOL. Stay safe and warm this winter. Cheers!
Good job as usual you have the right amount of mechanical knowledge for what you are doing and know how to research to do it right i would have done it a little differently with the same results but the trolls and safety clowns would have got me one tip when putting the tire back on put the tractor in neutral and spin the hub to line them up or put down some plastic with dish soap on it makes the tire slide easy good luck
Ps I have been falling this and thought of a good bonus with the chains is they will brake up some of the ice as you work this winter thanks a gain
Good morning and thanks Dale! That's a great idea about spinning the hub- didn't even think of that. LOL. But would have been much easier. Thanks again and enjoy the weekend!
You just walked me through my next mod, thanks. Cheers.
Good luck John!
You’re more of a mechanic than you know. Good job. What I am surprised by is red loctite should be released by heat or it used to be. And you are right about rechecking torque because of painted surfaces on spacers. You impress me more every video by trying and learning new things. Most people’s limits are because they are afraid to ask questions when they don’t know. Keep up the good work. Cheers!
Thanks very much David! A few folks, including Guy, suggested the heat. I tried it on two of them but it didn't;t seem to help much. Guy figured it might be some other type of compound was used. Thanks again and I agree, you have to keep trying to learn new things. Cheers and have a wonderful weekend!
Thanks very much for this video Gord! I just installed wheel spacers on my L4060. The cram nut method worked like a charm. The hardest part was putting the loaded wheels back on. Did this on a beautiful 20 degree November day. Just waiting for my chains to arrive now.
As a mechanic of 38 years I will say you did a good job. With jobs like this, just take your time, be safe, and after it's done you will have gained some experience.
Good day and thanks very much! I appreciate it. Was a good learning for me and really happy it worked out. I checked the torque twice and it is holding so I will check it again next week. Thanks again and all the best!
Fantastic instructional video GP. I don't think you need all the disclaimers, I doubt a tractor dealer mechanic would have done it any better. I've been thinking of wheel spacers for a while for my Kioti to help with stability on the hills of my property, seeing you do it has given me the confidence to have a go. I'm sure I'll be watching this video a few more times. I reckon you'll have the right setup for the snow this year.
Good morning and thanks Mark! LOL. I put them in just in case. :) I have to admit, it was a challenge for me but happy it worked out and I agree- I think I am ready for the white stuff now. Have a great weekend and good luck with the Kioti! Cheers!
I just ordered wheel spacers for hill stability. Your video is extremely valuable giving me a good idea what I am facing. I am going with 3” spacers for the rear and 2” up front. Thanks for this informative video. And I agree with another comment, your mechanical skills are really very good. I felt bad for what you asked your small jack to do but it came thru.
Morning Greg! Good stuff. I am happy it was helpful. That little guy is rated for 4,000 lbs believe it or not, and the tractor weighs about 2,000 so I think it was ok. Good luck with the spacers and have a great weekend! Hope you are getting the sunshine and warmth we are here. Cheers!
How much do you think half or even the whole tractor weighs?
What’s the smallest jack you have ever seen rated to lift?
What is there to worry about??
I'm surprised that those studs were threaded into the hubs and not pressed in like their vehicular cousins. An excellent video GP and one that I am sure will benefit a lot of compact owners of all brands. You did good sir. Btw, you should swing by one of these days when I have to change one of the fluid filled 14.9-38's....LOL. It should take two men and a boy, but you know sometimes a guy has a trick or two up his sleeve.
I continue to be impressed with your very succinct and professional way of delivering understandable information to the viewers !! Now a hamfisted backyard shade tree mechanic like myself would have stuck any old nut on the studs and welded them in place, then used an air impact to remove them. Like I say though: Don't do as I say and don't do as I do.....LOL Again, great video sir.
LOL! Well, one of the mechanics suggested I do the same thing but of course, that would require I had a welding machine and the air impact, and knew how to use them. LOL. But hey, you make do with what you got. Thanks T - mission accomplished! Have a good week my friend!
Thanks for another great video, I had success with the cram nut method. My B2301 studs battled me to the very last thread, I was a mechanic years ago, and never had a battle like that with Loctite or anything else for that matter - lol, I thought for sure that first one was cross threaded, but nope, every last one was like that. Then I hoped for the other side would be different - lol,, nope.
Thanks again, lovethe videos
Great job GP, really did a great video too, now go play some for a couple days and check the torque a couple times and you’re ready. We had snow up in Amarillo last night according to the weather. We are to have a 50’s day tomorrow in East Texas so winter might sneak into our area this year? You all be safe up there and have some fun. Get Carol to start getting involved some, you can have cooking, or coffee breaks in your videos and walking into or out of your videos. Thanks for sharing with us. Hey Guy, how you doing? 👍
Thanks ODD! Lots to do this weekend here. I had flurries this last week here too so it's getting close. Will pass along to Guy. All the best to you and yours! Cheers!
After watching this I am for sure going to try the studs instead of the chains, wow you are the gutsiest. Dean
LOL! That was a memory, for sure Dean. Happy I don't have to do that again. Cheers!
Great Video, they make big difference in stability, I put them on my B3030HSDC.
Thanks OT! Cheers!
I'm glad i watched this - I'm going to put chains on my B2601. A technique for putting a tire back on a rim. I'm no longer strong enough to sit on my butt and lift a tire into position. So I use a fulcrum and a lever. For a tire the size of the B2601 rear I'd (probably) use a 2x4 flat on the ground and parallel to the tire. Then get something for a lever - maybe another, longer, 2x4. Again, I'll have to try different sizes to get it right. The tire needs to be tilted a little in at the top I push down on the lever to balance the tire. Then you can move the tire without the weight a little left/right and the lever can be used to adjust height. I've done this myself on 3/4T truck tires. You may need someone to run the lever for a B2601 tire. But is sure beats lifting. Oh yes, BP is a Canadian - I should have typed Tyre...
LOL! Tire is ok - I understood. :)) Cheers and Merry Christmas!
Great video Gord . Have never seen anyone install spacers on the wheels before . I'm sure you have helped out quite a few people . You have a good Kubota dealer because he got you the parts . Al from Lummnah Acres needed parts for his mower and the dealer ( Kubota ) told him that he had to order the parts on-line himself . Talk about bad dealer service . Larkin looks like a great dealer to deal with . Let the snow fly . Gord is ready for it . LOL
LOL. Good morning Henry. Yes, Larkin is awesome. This happened on Friday afternoon. I called them and they had the parts ordered in and at the parts desk at 8:00 am Saturday morning. I though for sure I would be waiting with the tractor on jack stands for a few days. They are great. You bet! Let the white stuff come! Cheers and all the best Henry!
Like the video GP on Wheel spacers , thanks .
Cheers Leo!
I used the same spacers on my B2601. Nice addition
Great job, the Internet is an awesome learning tool. You do a great job on your videos. We're finally happy to get some cool weather in Alabama!
Good morning and thanks very much! Happy the cooler weather is coming your way. Getting very chilly here now so I was happy to get this done before the white stuff gets ere. Enjoy the rest of the weekend!
Hey hey Gord you will be glad you have done that I am sure . Nice job
Thanks AK! Cheers!
Good job and well thought out . I’m sure lots of tractor owners will appreciate this demonstration 👍👍👍
Thanks very much Ridgeback! Enjoy the weekend!
Nicely done and very informative.
Thanks Mike! Cheers!
Very nice video and job well done. One of the nicest channels on UA-cam.. Thanks for your time and effort while making these viseos. Many blessings to you and yours.
Good morning Lewis! Thanks very kindly - very happy you enjoy them. Have a wonderful weekend and all the best to you and yours as well!
Nice video. Looks like plenty of clearance for the chains now. Good job. They make a Stud removal replacement tool for about $20 U.S.. I have used one on several occasions. Thanks for sharing.
Thanks TT11! Cheers!
RED Loctite generally requires heat to break loose ( that is why you use BLUE if you expect to remove the studs ). This does not mean red hot - and try heating the stud only to avoid warping the flange. Good job using the tools at hand. I am glad none of them broke off. Cheers and take care
Thanks for the info David! Me too. Took a while but all done. Cheers and enjoy the weekend!
Great video, Thanks.
Great video! I’m considering a Kubota as my first tractor purchase soon, and your videos have been very helpful! I’ve been a professional mechanic for years, and as others have suggested I would recommend heat to loosen the loctite prior to removal.
Well done - that wider stance should provide a bit more stability as well.
Thanks JimmyD! Cheers!
A few ideas, heat studs ( it will break the lock tite bond ), add beet juce ( or some other non- corrosive liquid ) to all your tires for weight, stability and traction. Have fun, be safe !
I just found your channel recently. Great content. Thank you
Thanks for watching and for the kind comments. Cheers!
GP, the strong part is the top jaw on an adjustable wrench. I noticed you were hammering on the bottom jaw of the wrench to get the studs out. You could break the adjustable wrench that way. I really enjoyed the video you produced as I want to get spacers for my B2601. You used 1 1/2 inch spacers I would like to use 2 inch but I don’t know how they will work with my 60 inch mid mount mower. I need to talk to my dealer. Thank you for the informative video! Wayne from Wisconsin
Good morning Wayne. Thanks for the great advice. Good luck with the spacers! Cheers!
I think you are braver than I am. I'm not sure I would have tried that, but I did enjoy watching you do it. Thanks. Hi Guy, hope things are well with you and yours.
LOL. Thanks DA! Cheers!
Excellent Job, well done
Thanks Hughie! Cheers!
That is a great teaching video. Thanks for posting!
Thanks and all the best Allen. Cheers!
You're all set and ready now GP. I think I would have went with 105 torque value as well. Good call
Hey thanks Dean! Have a great weekend! Let the snow fly!
Good evening Sir, very well done GP !!! You are very good at showing and demonstrating safety practices and tools handling too !!! Like at told you before, you are mechanic !!! Keep up the good work and you too have a great TGIF !!! Cheers !!!
LOL! Thanks Dave TGIF to you too my friend!
Nice job
Thanks Larry!
GP-
Your a smart guy! Can you imagine doing that job a couple weeks from now? Cold! Way to be prepared! Cheers
Sure happy we got it done now. Man that would have been a tough one. Thanks and enjoy the rest of the weekend!
Great video coverage of a job really well done, Gord! I’m trying to imagine doing this myself on my L4060 with 14.9x24 loaded tires LOL, I believe there is over 400 lb of liquid ballast alone, not even including the weight of the the tire and rim... not something you’d want to fall over!
A few years ago, my brother helped me replace the brake pads on my old Massey 50 (12x28 loaded tires), and even with two of us it was a hair-raising job. I’m not getting any younger so probably a job for my dealer should I ever need to do this.
By the way, I concur with one of the other comments that with care and patience, some heat, even from a household propane torch, can be quite effective at breaking down locktite - even the “permanent” stuff. Nevertheless, a few well chosen tools and strong arms can also do the job, as you well demonstrated! Cheers!
Good morning Dave! LOL. I concur. Not sure I would want to try taking those off either. :)) I tried the propane torch on a couple of them but not sure it really helped at all, but then again I may have done it incorrectly. Have a great weekend!
Looks like a good job to me and I know this is a bit late but for the future I'll share a thought. First as others have said bit of heat makes it much easier to get those studs out and second if you're replacing them with new I have found that welding the nut to the old stud makes short work of getting them out. I know, "now you tell me" any way you got it now. Thanks for sharing and good luck with the snow!
LOL. - Never too late for good advice Rick. And always appreciated. You never know - I may need that advice for something else that cosalong one day. Thanks again and all the best! Cheers!
Wow... you did well. That was very enlightening. I am really surprised that given the way the studs are secured to the hub that Kubota would use spacers that need new longer studs. With a lot of spacers on the market, the spacers will bolt to the hub using the original studs and nuts and then the spacers themselves will have a second set of studs for attaching the wheel. Along with plenty of clearance for the chains you should have improved stability on side slopes.
Good day and thanks Joe! Me too. I had seen another aftermarket type that was designed as you suggested so I assumed the Kubota ones would be similar. I'm all ready now for the winter! Cheers and thanks again!
Great job GP..... I ruined a wheel stud when installing my 3rd function valve... your video has given me the confidence to repair it myself👍
Thanks so much Daniel! Good luck with the repair. Cheers and all the best! Be safe!
Great video.
G P a lot of work goes into something that looks like a easy job reminds me when I started building Manitowoc Cranes the were all hand built but as you said gives you pleasure when done
God Bless
PaK
Thanks Peter. It sure does. Happy I was able to get it done myself. Feels good! Cheers!
Wow --- a job well done my friend
Thanks so much Herb! Have a wonderful weekend!
I would never have thought of this and would’ve ended up losing hydraulics at the worst possible time. Well done, preventative maintenance at its best
Cheers John!
Very good mod for your tractor. As for the original Kubota lug nuts I have found them to be of low quality. The metal is soft and the walls are thin. I always replace them with better quality nuts on any tractor I own.
Thanks K! Have a good weekend!
Nice work and great video Gord! Very instructional. If you ever have to - I hope not - remove the wheels and put back on again, grab ya some 3ft bars, pipes, even old tool handles like axe handles and put on either side of wheel/tire and use leverage to help lift up and manuver wheel/tire back in alignment and up in place... Save that back my man. Hope your family has a wonderful weekend.👍☺
Morning BB! Thanks for the tip! My back thanks you too. LOL. All the best to you and yours as well!
Good job catching it early. Nicer doing when its warm out
Hey good evening BD! So true. I have no garage so always better before the snow flies and temps get negative. Cheers!
Great job. What a pain in the neck getting those wheel studs off! Little snow here in central VA, so I shouldn't have to worry about chains, but still a good watch to add to the mental catalog. Thanks!
I just put 3" spacers on my L3901 and I did not remove the wheel studs. They fit perfectly on existing studs and came with the hardware needed to attach the wheel. Also, I have a dolly made with 2x4 and 2x6 which I slid right underneath the tired. I then strapped the tire on to the dolly and never had to lift or roll the tire during the whole process. Just move it out of the way.
Good morning Waya. I have seen those 3" spacers - the dolly was a brilliant idea! Good stuff. Have a great week out there!
@@GPOutdoors The only problem how is while I have much better stability, I need a wider box blade! It never ends.
LOL!
wow, that was a hard enough job without having all the extra work of explaining every step and keeping the cameras rolling. thanks for taking the time. great video.
LOL Dan! Yup, it takes a little longer (ok, alot ) but well worth it if you folks enjoy it. Thanks again and have a good weekend!
Glad I don't have to deal with chains and snow, just earthquakes, fires, etc. lol. Your rear tires looks like the same size as my L2501. Mine are filled too and I'd hate to have to change one. My JD 4320 are filled also and weigh around 4-500lbs. The only thing I've heard that's an issue with extending front/rear wheels out, is the possibility of axle/bearing damage due to excessive weight on the end of the axles. Those wheel extenders don't extend the wheels out far enough to be a concern tho. I've seen tires extended out 12+ inches and that's an issue, especially with loaders and heavy 3pt loads.
Have a great weekend.
Cheers my friend.
Good morning Tim! LOL. Thanks for the good info about the width of the extension. I had read the same thing and found an aftermarket type but they were 3" spacers and so I thought it was best to go with the Kubota spacers since I know they would be specifically designed for my tractor. They are only 1 3/8" inches wide. I am happy I did now, as several folks have said the same thing you have. Hope all is going great! Cheers!
@@GPOutdoors I don't know if you get the US news up there, but north of me there is over 140k people under evacuation orders this AM (10/27) and around 2.2M people without power due to PG&E power shutoff. I can see a fire over in the west hills on my NW tower cam. The Kincaide fire really took off early this AM due to wind gusts of up to 80mph in the Napa/Santa Rosa areas. 2 Old wineries have already burned. I have a friend who has property in Lake County and I don't know if that area is under evacuation or not. I assume it is. I have wind gusts on my commercial weather station of 28.8 mph so far. This is supposed to last thru Sunday eve up to Monday 1100. Some of the areas that burned in the Tubb fire of 2017 are part of the evacuation order. Not looking good so far. The way Calif is going, I mite have to move to Canada, lol.
Have a great day Gord.
Cheers from Tim in SF Bay Area.
hey thanks for telling me Tim. My daughter is in LA currently but hopefully ok. Unfortunately I don't have TV or any reasonable news up at the cabin so while I am here, I have to rely on Guy or Bob to fill me in on things. So I had not heard. Hope for the best for everyone. wow. thanks again. Cheers!
Another great video GP!! I really enjoyed watching! You were very detailed and you covered all the bases! You made a pretty tough job look easy! lol I like the clearance you have now for them chains. Have a great weekend GP!!
Thanks very much John! Hope all is going great and hope the temperatures have cooled off a bit for you. Be well and all the best!
Good job Sir!
Thanks so much Ranger! Cheers!
Hi Gord! Man, that looked like a pain to do but well done. This was a very good instructional video for a non-instructional video! LOL. You clearly did you homework ahead of time. Thanks for sharing!
LOL! Thanks very much DIY! Cheers!
I don’t know what the saying either correct terminology is in Canada but in Oklahoma it’s jam nut. Thanks for all the great UA-cam content 🇺🇸
LOL. Thanks Charles! Yes, I think I messed up the terminology perhaps. A "Jam Nut" is, up here, an actually specifically engineered nut used for this same purpose but it is designed and built to be the nut you put behind the main nut. I think "Cram" nut is kind of slang for when we just use two nuts and tighten them together. LOL. In my case, I didn't;t purchase a Jam nut - I just used two of the wheel nuts together. Perhaps If I had though, maybe I would not have cross thread all the nuts. Thanks! And enjoy the weekend! Hoping for a little sunshine up here. :))
Great video GP.
Thanks Erick! Cheers!
Wow. Great video.
Thanks Emery! Cheers!
Good job. FYI if you put a little heat to the studs from a little propane torch you would have simplified your job. Locktite is actually a plastic sealant and heat melts it. You could have almost taken them out with your fingers. They would have gone back in easier too with that little heat. I was a mechanic by trade...
Hey good day and thanks Richard. I tried the torch on two of them but it didn't seem to help any. Guy suggested they may have used a different compound ( or i was applying it incorrectly). But wish it had worked. LOL. Thanks again and all the best!
Nicely done, GP. I'd say you'll appreciate the extra 2.5" of clearance when the snow starts flying.
Morning P! I am looking forward to it. All the best!
Very informative video! I originally added spacers for stability. Nice to know they will help with chains in the future on my BX! I'm sure those loaded tires were a hand full to move around!
Thanks Frank! Good point - I understand it should give me a little more stability too so another great benefit. Have a good weekend!
wow! thats some work gp! i never would have thought those studs was threded on the hub side. though they would be like cars with the ribs on one end and threads on the other side. well you learn something new everyday.
LOL. It sure was a workout for me. I was down to my t-shirt trying to get them off. LOL. Have a good one Dale!
What a pain in da butt.
Glad i picked mine up with wheel spacers, 3rd function and rear remotes.
You spend more time working on it than working it : )
Morning Rand. Yes, it was a tough job for me but happy I got it done. I wish I had known I would need them when I got it. Have a good one! Cheers!
Let me give you a tip when you use the nut trick to take off the tire bolts put the lug nuts on against each other grab two wrenches for the front one and one for the back one what's your going do is lock them together as you tighten the back one go loosen on the front one till tight now they are locked to take off the wheel bolt use only the front nut to take it off the back nut going keep the front one from turning and make sure you use the right wrench that fix the nut a loose one will round it off
Try a heat gun next time and a good impact drill. All shops should have these items.
Good job and great advice.
Thanks MM52001. Some great advice. It certainly would have made it so much easier for me. Have a good week!
@@GPOutdoors thank you, off to watch more of your videos.
LOL! Thanks so much MM52001. Be well and have a good evening. :))
Thank you for doing these videos...:)
You're most welcome John! Thanks for watching and for the comment! Cheers and enjoy the weekend!
Good evening GP you did a great job and the tractor looks pretty good with a wide but lol of a great weekend with your family
LOL. I was thinking it looks kind of mean now. Kind of like a hot rod. You too Denis!
With those spacers.... have to make your trails wider! Cheers
LOL. Cheers Tom!
trhank you!
Are those snow flakes I see? Absolutely love the videos!! Makes the day fly bye!!
LOL Kristopher! Funny because I actually had flurries in the morning before I started filming. Thanks and very happy you enjoy them. Cheers!
Good job GP.......now thats prolly the best video out there on this particular job......lots of good info for sure.....thanx for posting my friend and have a good week....... :)
Hey thanks so much my friend. It was quite a challenge but happy it worked out. Cheers and all the best!
Good job GP a couple of suggestions. A little heat goes a long way on loctite. A propane torch is more than enough. Also please don't hammer on adjustable wrenches. The jam nut method you want to tighten them against each other with two wrenches to jam them against each other then use the inside nut to loosen the stud. There is also a stud remover tool made for the job.
Hey good morning and thanks for the suggestions James. I appreciate it. I did try the propane torch on two of them but it didn't seem to help much (but I may have been applying it incorrectly). Agree - didn't want to hammer on them but they just would not budge at all. I had a length of pipe as well to try to get leverage but there is little room under that fender to use it. I had called two parts places in nearby towns but neither of them carried the stud remover. I think that would have been ideal for sure. Thanks again for the helpful advice. Always appreciated. Enjoy the weekend!
glad to see you did not run it very long before putting the spacers on only seen two things missing a picture of guy and a cheater bar for the pipe wrench and a propane torch for the studs okay that's three things. also Paul short also o&d life UA-cam channels had to put there spacers on
LOL Bob! Well, let me be honest. I think I called Guy about 10 times throughout the project. I attempted using the propane torch but it had minimal positive effect ( Guy's suggestion), and he gave me a cheater pipe but I didn't need it. LOL. OK, you got me! Cheers and thanks for the comment and for watching! I think you and Guy would get along quite well. LOL. Cheers!
Nice vid GP! If you ever have to take the wheel off again, I’d suggest you get yourself a long breaker bar, and your foot to do the wedge method and you’ll get you tire back on just like you do a car. Look up changing a semi truck tire. Much easier but great vid
Thanks for the great tip! That sounds like it would have been much easier for me. Cheers and thanks again!
Nice job, GP. The job never is as easy as it appears when someone else does it, right? Excellent walk-through and you'll be set for those chains. I'm glad you decided on the spacers b/c of those chains. I was wondering what size spacers you were going to install. The spacers appeared to give you a nice amount of room to allow for chain play. Enjoyed a full-watch. See you on your next video.
LOL Houndsman! So true. I remember telling Guy the "simple" steps I would go through to get it done. And then I called him about a dozen times while I was doing it. LOL. Sure seemed simple when I was planning it. Have a great weekend and thanks!
When you are dealing with heavy tires use a long bar and slide it under the tire, perpendicular to it. It makes it a lot easier to get it lined up. I use one 3-4 feet long.
Hey thanks for the advice TP! I will try that if I need to take them off the next time. Cheers and all the best!
I think you also gave yourself a bit more stability with the spacers by widening your stance, should prove beneficial on uneven ground and with heavier loads.
I am looking forward to seeing how well it rides in the forest now. Cheers Thomas!
Once its cured, thread locker can be "softened" into compliance with mild heat. Soaking the hub with a heat gun before you start would make it a world easier. A torch would work too but then the paint gets cooked-off and you risk damaging the axle seal.
Hey thanks so much for the great advice Timber! Good to keep in mind if I need to remove them again or adjust anything. All the best!
Looks like a lot of work on the wheel spacers. I took the easy way and used Bro-Tek wheel spacers that just bolt in to the existing studs, and then have bolts/studs that attach the wheels to the spacer. Easier, but now I will have to remove the wheels every so often to check the torque on the studs holding the spacers on to the tractor. Easy now, harder later..... Cheers!
Thanks! Yes, I saw those - a few folks mentioned them. Much easier for sure getting them on. LOL. Cheers and all the best!
Stud remover and installer would have been great. Some times your local rental place has tools.
Good morning Jim. It sure would have been much better for me. I called 2 automotive places in nearby towns and the one rental place and no one had one. But wish I could have found one. I think it would have been much easier for me. Thanks for watching and enjoy the rest of the weekend!
Being from Caseville in the thumb where it's flat I appreciate the need for a wider foot print. I know the landscape of the U.P. . Our daughter went to northern, go cats, and getting a tractor back on it's feet doesn't need to happen when you can prevent it. Thanks for the info. My B2620 may get the same. Keep the greasy side down.
LOL. Cheers Ralph!
Why would you appreciate the need of a wider footprint on your flat ground?
What? Ponder my comment, sir. I'm sure the answer to your question will be quite obvious.
Ralph Ross just explain the first sentence.
@@jaxturner7288 you'll figure it out.
Well done.
Note for everyone. I worked 40 years on my knees and it wasn't until I retired and moved up and bought a kubota that I found the perfect knee pads. I was using them I somehow had but didn't know I had and I couldn't believe how perfect they were. They do not hurt and I put them on every time I go outside to work even if I don't feel I need to kneel. I end up coming into the house with them on because I forgot I have them on. I found the online at HD. They are Tommyco brand. The 1" foam with 1 strap. Less then $5 American!! I have about 12 pairs in different areas and have even away about a dozen pari to friends who I see abusing their knees. No replacement knees for me!! They don't stock them. Tommyco T-Foam Light Duty Kneepads $4.92 pr. Don't let Light Duty fool u!! Best ever!!!!
Thanks for the great tip Tom!
YVW my friend!!
Well done! Kubota would not do a better video. They should target you for their promotion! Thanks GP!
LOL! Thanks Joe - have a great weekend!
yep I like it, I m thinking to do that to my 3200
Cheers and thanks Frank!
You're using the adjustable crescent wrench backwards, that's how you break the adjustable jaw!
Nice job GP. My massey uses bolts instead of studs. The job would be much easier for me. 😉
Thanks Alain! I think so too. Cheers!
Again...good job cheif! I always wanted to know how much it would take to get the job done. I wasn't a believer in chains for my 2650 but this last storm of 30 cm. Of wet snow made me reconsider!😎 keep an eye on the tree line for you know what!!!
LOL Mike! We had a flurries here a few days ago. It's on its way...Cheers!
Santa needs to bring you a cordless impact
now that we have the spacers on the tires we can measure the outside of the tires for the new planter boxes haha maybe Joe will send you plans
LOL. If I am lucky, he'll make them too. :)) Ok, not sure i can talk him into that. Cheers and all the best Bob!
i was more or less getting at the studs are they right hand threaded on the hub and im sure thier threaded on the lug nut side. but on vehicels you just pull them thru lug nut hole. anyway cheers and have a great day gp!
Yes good day Dale. A few folks mentioned that about vehicles ( cars). These are threaded into the hub. They go in clockwise and come out counterclockwise. And not sure but I am pretty sure the threads are interference threads because they are difficult all the way through when removing or putting them in. I hope that answered your question (?). Cheers!
@@GPOutdoors yep thank you sir. interesting. and okay we have those kind of threads at my workplace. great for saftey! those kind are way more difficult to work thier way loose. ok have a good one bud!
I know you have bought a larger tractor but were you pleased with the 2601? Looking at different compact tractors & the 2601 is in the running. Thanks