I just checked my 2501 and it was completely empty. Thank you for the heads up ! I would have ruined my tractor if it wasn’t for this video! Thank you so much!
Great tip for those who are unaware. I checked my Kubota tractor day of delivery when new. And 4yrs (160hrs) later, its still clean and on the full mark on the dip stick. I very diligent about checking ALL my fluids before i start & use my tractor`s. Most people don`t, and then that is when they get in trouble. Its not hard to check the fluids before starting it.
Thank you 🙏. I went to the garage. Broke the check open, nothing. Broke the fill and put an additional 2.5 quarts of 85-90 until it started leaking out ….. not ok with this. I’m so glad you posted this video.
Thanks buddy. Saw video about a week ago. Finally found my front axel drain and fill. Fluid was trans fluid, changed with 90 weight heavy oil. It was considerably low, not touching dip stick. Thanks! You increased the life of my axel.
It takes some time for it to go through the pivot, especially when it’s cold. Don’t forget to take your grease gun to the pivot after you open the vent. I change my front end every hydraulic change. I use gear oil, the thicker the better. 👍
This video is performing really well! I changed it at around 900 on my M6060, still looked clean. This is something that should be checked day one on getting a tractor, my bx was very low and I didn’t catch it for a long time. I only did check because of hearing other people talk about this issue. Appreciate you mentioning my channel! Excellent video Richie!
I did a video last summer on my channel Ben and when I checked the level, it was low. I checked it after I brought the tractor home but hadn't run it in 4Wd. I was shocked at how low it was with just over 200 hours on the tractor. Since filling, I have checked twice and the level is right where it is supposed to be. I think Richies theory is spot on. Totally makes sense to me.
Thanks for the great intel brother! Getting ready for my 50hr service for my L3901 so I'll definitely check it now! People like you is why I do my research on here! Thanks again!
I’m picking up my new L3902 next week! Definitely gonna check these fluids also. Just traded in my L2501…never saw a leak so figured it was fine..…only had 135 hrs
My B7800 has a dipstick (yellow plastic) on the front axle, which looks very similar to yours. Industrial sight plugs are available for many threads, and it might be worth retrofitting the non-dipstick models, then you could check the level with a flashlight. My B7800 (2006 model year) had 570hrs on it and was a tad low when I got it. I did a full service on it with all Kubota parts from Messicks and used UDT-2 (7 gallons) as well, not cheap but cheaper than replacing the finals or worse. I do need to be more diligent about pre-flight checks, especially when it's sub zero out. Good video, hope it saves some tractor owners big repairs, Thanks!
It seems this video has raised a lot of awareness which was my intention. I dont think being two quarts low will cause catastrophic damage but better to be within specification versus not even checking it!
I just bought a 2022 L2501. It’s my first ever tractor. I check all my fluids when they delivered it to me except the front axle. Mine took almost a whole gallon of Super UDT2 fluid. Luckily I only put 4 hours on it before realizing this issue. Thank you so much for this video. You saved me a big headache down the road!
Agreed, i would hate to see someone go to do the 800 hour service and come to find that they have been low on fluid for that many hours. And by that time most likely out of warranty.
If you use your tractor to remove snow you should swap your front axle to the 85-90W gear oil. What happens is you are using it and working it in the cold. When you are done you park it and all the fluid got warm from working so it melts the snow. The gear oil is pretty thick and does not warm up as much as the hydraulic fluid that most manufacturers put in there. As everything cools it contracts and can suck that water inside your front axle. Their has been many people that have popped their dipstick out only to find their gears and front axle were all rusted up from water contamination. The thicker gear oil does not get as warm and you don't have that problem.
Great tip, Richie! We shouldn’t assume them come full from the factory or don’t lose oil. I changed mine at 400 hours, because like you, I thought 800 hours was too long to wait. Thanks for sharing!
I agree with your assessment. I doubt it's dealer policy, but the mechanic is cutting corners. Of course if there is an issue, the dealer will say you are not doing the proper maintenance. Great Tip Richie - Enjoy the journey - cheers
I think the l-2501 requires 4.5 litres Canadian{?}.i checked mine and it required 2 litres of oil.They only put in half the required oil.That really opened my eyes as to the inspection and PDI of this piece of equipment.For the amount you pay for Kubota,there should be no guessing,it should be spot on!Good vid.
Thanks for the info. When I did my 200 HR service on my 2017 BX I checked it. It was 1-2 qts low. My Kubota service manual says to "change" it at every 400 hrs. My fill plug on my Kubota 2380 for the front axle case is on top Driver's side. I also found a socket extension buried/stuck under the tractor and a miscellaneous bolt and washer just laying around. Can't remember where, but I wonder who is prepping these for delivery? Oh, and also, the height adjustment knob for the mower deck is just impossible to turn at times without a pair of large channel locks
Thanks for the video. I just changed the axile oil in my BX23S. I only had 150 hrs, but saw it was low. Turned out it was a little over half but I didn’t see ant meatal shavings. Shame because the dealer supposedly did my 50 hr check. I have now went back and did everything they charged me for.
How's she goin'? Great tip here and thanks for sharing. I have a Massey Ferguson GC2300 sub-compact tractor and the front axle leaks oil around the pivoting joint for the offset drive to the wheels. I check this oil level probably every other time I take the tractor out as it is often low on oil!! Thanks for sharing and take care!!!
The use of UDT in the front differentials on these tractors can lead to leaks in the knuckle seals. It was recommended to me by the dealer to use 75/80 weight gear oil which is thicker and will not bypass the seals.
Thanks for the reminder it is a lot easier to check on a B2601. I check it every year but this is a new year so heading out to do it right now before I forget😁👍
it takes forever for the oil to work down into the gear reductions, So like you said you need to use it for days to recheck. do a change in the summer when its hot, leave the oil out in the sun so it thins out, their not using oil, their not full .. unless their leaking
Received my L2501 DT Friday, opened over flow…nothing…opened fill plug and stuck my finger all the way down. Only felt residual on axle tube, I could not feel a fluid level, I will be topping it off tomorrow, glad I checked with .3 hours cause it’s low. Transmission oil is also not on sight glass, pointed it out from dealer deliver he said he will give me some free fluid. Thanks!!
just got my new L2501 delivered awhile ago. put it strait into the garage until this weekend. gonna check this and all the other fluids. Thanks a bunch for the heads up and keep up the great videos 💪🏻🤙🏻
Ive had an issue with my 40 year old L where there would be too much pressure in the case when warm; causing fluid to blow by the seals. First I tried a plastic stand-up vent but it got torn off. I got a bolt with the correct thread and drilled a 90 degree 1/16 hole through the head and bolt body. This provides ventilation for expansion and contraction.
wow, I went to check the level and the bolt tried to fly away from the pressure. I never thought of that. Thanks for the comment. Maybe it will stop that oil leak I am having without having to split the tractor.
Can’t go wrong keeping a close eye on your fluids. My truck isn’t always polished up, but you can bet the bank all of my fluids and filters are on point! Bought my b2601 brand new and there wasn’t a fluid on the machine that was right when I got it. The dealer I bought it from also needs to get there techs a new torque wrench. Ended up going over every bolt on the tractor after two chassis bolts and a rear wheel lug fell off just mowing with the belly mower. Ridiculous quality control. Fact is, we all make huge investments in these machines, take a few minutes and keep thing tight and topped off and you’ll get several thousand hours out of these tractors.
Good morning Luc, Im really glad to hear that you were able to address it before putting too many hours on the machine. Hope you are staying warm up there!
@@HillsideAcres 👍🏻, it’s really cold 🥶 but the extreme cold warning has ended, temperatures should be reasonable for this week 👍🏻. Have a good one 🙋🏼♂️🙂👍🏻
My BX was low too straight from the dealer. When I changed it , went with gear oil and just elevated the axle a bit so I could rotate the wheels by hand. That settled the oil into the hub straight off. Been good since and I’m at 680 hours. Surprised your 2501 doesn’t have a dip stick for the front axle. Thought that was standard. Thanks for the reminder though as I should probably change mine again soon.
you are correct, have a mx 5800 300 hours, never checked the 4 wheel drive never seen any leaks, until last week the left bearing shelled out when driving and the wheel fell off nice. anyway the axel cost me 458 dollars and the 2 race bearings and seals, another 150 dollars plus the 7.8 quarts of lube, so check are pay the price, if Kubota did the repairs you would be looking at over are close to 1500 are 2000 dollars in repairs
As watched, I had to quickly check on mine as the dealer told me to use gear lube Front axle case . (SAE85-,90 gear oil) Then double checked and either or could be used. Front axle case KUBOTA UDT or SUPER UDT fluid* or SAE80, 90 gear oil. I had serviced my B2650HSDC-TLB at 400 hours and I replaced the existing fluid which was gear lube from the factory.
@@HillsideAcres so I am wondering how to lift the brush hog implement is there a lever or something I need to push to get it to lift some in the back to get it off the ground?
I have a brand new BX2380 ( about 60 hours on it ) and now am very curious to see how much oil I have. I will be checking on this once spring arrives. Thanks for your video ! it's much appreciated !
Every 800 may seem excessive but its a good practice to drain and look for metal chips, those angle drives don't like chips and the bevel gear teeth are under a massive load sometimes in 4wd. A couple quarts of oil vs $1k to replace gears, bearings, seals and a cracked housing.
@@HillsideAcres Had a Kubota blow up a front drive and farmer next door with a compact deere. Helped him go through his front axle after a sudden dissasembly. Good maintenance for the kubota also doesn't seem to mention pop out the front driveshaft couplers and lube them now and again every couple years else the rust eats the splines, not an overly expensive repair but it breaks when you need it most.
My L3130 started leaking at the left front hub. The seal was bad so I replaced both sides. It was a bitch but doable. Had to drain a lot of fluid because it has to fill both hub gear cases also. I don't think the dealer shorted me on fluid because I checked it a couple of times a year. I think driving it on the road for 3 to 5 miles every so often did it. I now trailer it everywhere unless it is only a half mile or so. I think I went back with the Super UDT. Thanks for a good video.
I just checked my L2501 and just like you said it was low and I only have 89 hours on it thank you the heads up hope to see more of your videos thank you Tony G
Approaching the 800 hour mark and getting ready to do some maintenance. Not sure where things are at. Wish I would have seen this sooner. Cross your fingers for me.
So, I’ve worked with 80w 90 gear lube before, and I’ve used Kubota super UDT. The latter falls somewhere between a typical hydraulic oil and an engine oil in apparent viscosity at room temperature, as I recall, and 80/90 gearlube is on the extreme end of viscosity, almost a grease rather than an oil. Can someone please explain to me how any piece of equipment can call for either of these products interchangeably in the manufacturer’s specifications?
I believe it comes down to the operating temperature where the tractor is located. If you feel more comfortable with a heavier viscosity oil, then use it. 👍🏻
Speaking of maintenance: Thoughts on the manual often saying, (ex.) "Check/change every 200 hrs or every 1-2 yrs, whichever comes first." The years of ownership seems a little overblown, but how seriously should I be taking it? Thoughts?
It’s a pretty good idea to go by the manual, checking on things like engine oil and hydro more often. A through annual servicing with regular greasing is typically good for most
My 40hp was on it's 50 hour check and i had real trouble getting the service guy in Thailand to check it. so i did it while he was there watching and it took half of a 4.5 litre can and the service guy couldn't believe it .
My 04 b7800 was bone dry, 900 hrs on it, i shutter to think how longs it been that way. Had it since 700 hrs. I was told the hydro trans hydro fluid was shared throughout the diffs.
Good morning Sir, you have a very nice AIR FORCE quality tool set 👍🧐 Yes Ben ( K&H tractor ) is a great reference man for sure 😉👌 Yes in deed, any fluids must be check often 🧐👍 OUTSTANDING VIDEO Sir and keep up your OUTSTANDING work both of you Cheers 🍻👌
I'm just about to buy one so thanks very much. Really useful. One thing...why do Americans all talk in future tense? "This is going to be your..." surely it just "is your" :P
I put a clear surgical hose on the end of my funnel that sits in the filler hole made life a lot easier to fill you should try it it really is a great Helping Hand
My 5240 had hydrolic oil in it from day 1,brand new,the left side gear assembly failed.i had to replace all of it,1500.00 bucks in parts alone,now they put in 50w synthetic.
I used super udt2 it was in the audio. Can also use gear as per your owners manual. I topped up with udt2 because that’s what was from factory and I did not want to mix
You have to check it hot not cold, because oil expands when hot, over filling can cause seals to leak, so don't overfill it cold. Seals leaking just a little bit will use oil and cause it to run dry, check it about every 200 hours, change it 800 hours.
@@HillsideAcres I used to run a Kobota mowing 40 acres of food plots once a month, we had front and rear end oil leaks because of sand intrusion into the seals, and that crazy seat they have on them caused me constant back pain so we switched to a John Deere Hydrostat, with Air ride seat, a lot easier on the back over rough hill sides and no oil leaks yet after 3200 hours of operation. Kubota makes a good tractor but for constant hard usage they just can't beat that Little Jhon Deere or a Yanmar, with Air Ride seat.
@@HillsideAcres They didn't in the L series that we had but the main reason we changed was everytime we crossed the muddy creek, we had to replace axle seals because of sand intrusion on the seals, not a problem in the John deere, if your not crossing creeks constantly then you probably will not have that problem.
I just checked my 2501 and it was completely empty. Thank you for the heads up ! I would have ruined my tractor if it wasn’t for this video! Thank you so much!
You are testamony to the importance of maintenance period. Happy you caught it before damage occured.
My L2501 is two years old……check my fluid level today and ended up adding almost a gallon! Thank you for posting this!
Great tip for those who are unaware. I checked my Kubota tractor day of delivery when new. And 4yrs (160hrs) later, its still clean and on the full mark on the dip stick.
I very diligent about checking ALL my fluids before i start & use my tractor`s. Most people don`t, and then that is when they get in trouble. Its not hard to check the fluids before starting it.
NICE! thanks for watching Larry!
Thank you 🙏. I went to the garage. Broke the check open, nothing. Broke the fill and put an additional 2.5 quarts of 85-90 until it started leaking out ….. not ok with this. I’m so glad you posted this video.
Thanks buddy. Saw video about a week ago. Finally found my front axel drain and fill. Fluid was trans fluid, changed with 90 weight heavy oil. It was considerably low, not touching dip stick. Thanks! You increased the life of my axel.
It takes some time for it to go through the pivot, especially when it’s cold. Don’t forget to take your grease gun to the pivot after you open the vent. I change my front end every hydraulic change. I use gear oil, the thicker the better. 👍
This video is performing really well! I changed it at around 900 on my M6060, still looked clean. This is something that should be checked day one on getting a tractor, my bx was very low and I didn’t catch it for a long time. I only did check because of hearing other people talk about this issue. Appreciate you mentioning my channel! Excellent video Richie!
Of course ben! Im seeing so many people dealing with being two quarts or so low on fluid which is crazy!
I did a video last summer on my channel Ben and when I checked the level, it was low. I checked it after I brought the tractor home but hadn't run it in 4Wd. I was shocked at how low it was with just over 200 hours on the tractor.
Since filling, I have checked twice and the level is right where it is supposed to be.
I think Richies theory is spot on. Totally makes sense to me.
@@HillsideAcres it's not full from new once you have filled it it won go down like that 👍
Thanks for the great intel brother! Getting ready for my 50hr service for my L3901 so I'll definitely check it now! People like you is why I do my research on here! Thanks again!
I really appreciate your support of the chanel!
I’m picking up my new L3902 next week! Definitely gonna check these fluids also.
Just traded in my L2501…never saw a leak so figured it was fine..…only had 135 hrs
Same here. I had no idea I should check it so often. I’m discing my field to plant pasture.
Just checked mine and had to add almost 3 quarts of oil. Thank you for the video.
Doing my 400 hour maint. on my Kubota L3302 now. Just added this to my list after seeing the video. Thanks for the heads up.
My B7800 has a dipstick (yellow plastic) on the front axle, which looks very similar to yours. Industrial sight plugs are available for many threads, and it might be worth retrofitting the non-dipstick models, then you could check the level with a flashlight. My B7800 (2006 model year) had 570hrs on it and was a tad low when I got it. I did a full service on it with all Kubota parts from Messicks and used UDT-2 (7 gallons) as well, not cheap but cheaper than replacing the finals or worse. I do need to be more diligent about pre-flight checks, especially when it's sub zero out. Good video, hope it saves some tractor owners big repairs, Thanks!
It seems this video has raised a lot of awareness which was my intention. I dont think being two quarts low will cause catastrophic damage but better to be within specification versus not even checking it!
Thanks for the video man. 3901 was a quart low at 40 hours. I'm glad I ran across this.
I just bought a 2022 L2501. It’s my first ever tractor. I check all my fluids when they delivered it to me except the front axle. Mine took almost a whole gallon of Super UDT2 fluid. Luckily I only put 4 hours on it before realizing this issue. Thank you so much for this video. You saved me a big headache down the road!
Thanks Mr Hillside.. after watching your video I went out and checked my l-2501. It was 1 and 3/4 quarts low. Thanks for the heads up!
Really happy to know that awareness was raised with this video! Thanks for watching!
Richie, thanks for pointing this out. For those of us who don't read the forums, this is great info we may have found out about when it's too late.
Agreed, i would hate to see someone go to do the 800 hour service and come to find that they have been low on fluid for that many hours. And by that time most likely out of warranty.
If you use your tractor to remove snow you should swap your front axle to the 85-90W gear oil. What happens is you are using it and working it in the cold. When you are done you park it and all the fluid got warm from working so it melts the snow. The gear oil is pretty thick and does not warm up as much as the hydraulic fluid that most manufacturers put in there. As everything cools it contracts and can suck that water inside your front axle. Their has been many people that have popped their dipstick out only to find their gears and front axle were all rusted up from water contamination. The thicker gear oil does not get as warm and you don't have that problem.
Thanks for sharing !
Thank you. I've never checked my B3030 now with 500 plus hours on it. I'll check the front axel as soon as I can.
Great tip, Richie! We shouldn’t assume them come full from the factory or don’t lose oil. I changed mine at 400 hours, because like you, I thought 800 hours was too long to wait. Thanks for sharing!
I’m right there with you martin. Being pro active on maintaining tools and equipment is cheap insurance for a reliable operation.
I agree with your assessment. I doubt it's dealer policy, but the mechanic is cutting corners. Of course if there is an issue, the dealer will say you are not doing the proper maintenance. Great Tip Richie - Enjoy the journey - cheers
Thanks bob. im happy that im topped off now!
I think the l-2501 requires 4.5 litres Canadian{?}.i checked mine and it required 2 litres of oil.They only put in half the required oil.That really opened my eyes as to the inspection and PDI of this piece of equipment.For the amount you pay for Kubota,there should be no guessing,it should be spot on!Good vid.
Liters and quarts are very comparable very slight difference, thanks for watching !
Thanks for the info. When I did my 200 HR service on my 2017 BX I checked it. It was 1-2 qts low. My Kubota service manual says to "change" it at every 400 hrs. My fill plug on my Kubota 2380 for the front axle case is on top Driver's side. I also found a socket extension buried/stuck under the tractor and a miscellaneous bolt and washer just laying around. Can't remember where, but I wonder who is prepping these for delivery? Oh, and also, the height adjustment knob for the mower deck is just impossible to turn at times without a pair of large channel locks
Good info, thanks. Aren't tractor fluids from the manufacturer just rebranded fluids with a nice mark-up?
Thanks for the video. I just changed the axile oil in my BX23S. I only had 150 hrs, but saw it was low. Turned out it was a little over half but I didn’t see ant meatal shavings. Shame because the dealer supposedly did my 50 hr check. I have now went back and did everything they charged me for.
How's she goin'? Great tip here and thanks for sharing. I have a Massey Ferguson GC2300 sub-compact tractor and the front axle leaks oil around the pivoting joint for the offset drive to the wheels. I check this oil level probably every other time I take the tractor out as it is often low on oil!! Thanks for sharing and take care!!!
Thanks for stopping by Mike, At least you know its always got good fresh oil in it!
@@HillsideAcres LOL For sure eh!!!
The use of UDT in the front differentials on these tractors can lead to leaks in the knuckle seals. It was recommended to me by the dealer to use 75/80 weight gear oil which is thicker and will not bypass the seals.
Either works fine, no leaks on either of mine. No liquid should be able to leak by
Thanks for the reminder it is a lot easier to check on a B2601. I check it every year but this is a new year so heading out to do it right now before I forget😁👍
Thanks for watching Mitch, seems like most have been low from the factory!
it takes forever for the oil to work down into the gear reductions, So like you said you need to use it for days to recheck. do a change in the summer when its hot, leave the oil out in the sun so it thins out, their not using oil, their not full .. unless their leaking
Kubota should have made a dipstick for the front axle. would have made checking the oil simple
Received my L2501 DT Friday, opened over flow…nothing…opened fill plug and stuck my finger all the way down. Only felt residual on axle tube, I could not feel a fluid level, I will be topping it off tomorrow, glad I checked with .3 hours cause it’s low. Transmission oil is also not on sight glass, pointed it out from dealer deliver he said he will give me some free fluid. Thanks!!
Glad to hear you got it all straightened out! Especially before putting the hours on!
just got my new L2501 delivered awhile ago. put it strait into the garage until this weekend. gonna check this and all the other fluids. Thanks a bunch for the heads up and keep up the great videos 💪🏻🤙🏻
Really appreciate the feedback! Sorry we have been lacking on any new videos! Have been super busy, will get back to it soon !
@@HillsideAcres no prob. i just found you all on here and am catching up on all the previous videos anyways.
I am not a Kubota owner but I think I will check mine now too. I have 48 hours on my Branson. Thanks for the video, Richie!
Im sure its the same style front end. Open up your manual and give it a check!
Yeah that's what they do just fill it up and the dealer don't check it so it's a 3000 dollar fix glad you are making people aware of it 5:32
Ive had an issue with my 40 year old L where there would be too much pressure in the case when warm; causing fluid to blow by the seals. First I tried a plastic stand-up vent but it got torn off. I got a bolt with the correct thread and drilled a 90 degree 1/16 hole through the head and bolt body. This provides ventilation for expansion and contraction.
wow, I went to check the level and the bolt tried to fly away from the pressure. I never thought of that. Thanks for the comment. Maybe it will stop that oil leak I am having without having to split the tractor.
Great tip! Wow I have 800 hours now but luckily changed my own at 400.
My Bx2380 was down by over a quart as well which I subsequently added. I checked the fluid levels after I took delivery from my dealer.
seems that they are all low!
Can’t go wrong keeping a close eye on your fluids. My truck isn’t always polished up, but you can bet the bank all of my fluids and filters are on point! Bought my b2601 brand new and there wasn’t a fluid on the machine that was right when I got it. The dealer I bought it from also needs to get there techs a new torque wrench. Ended up going over every bolt on the tractor after two chassis bolts and a rear wheel lug fell off just mowing with the belly mower. Ridiculous quality control. Fact is, we all make huge investments in these machines, take a few minutes and keep thing tight and topped off and you’ll get several thousand hours out of these tractors.
Great tip Richie, my BX was also low and I checked it after watching a video. Have a great week my friend 🙋🏼♂️🙂👍🏻
Good morning Luc, Im really glad to hear that you were able to address it before putting too many hours on the machine. Hope you are staying warm up there!
@@HillsideAcres 👍🏻, it’s really cold 🥶 but the extreme cold warning has ended, temperatures should be reasonable for this week 👍🏻. Have a good one 🙋🏼♂️🙂👍🏻
My BX was low too straight from the dealer. When I changed it , went with gear oil and just elevated the axle a bit so I could rotate the wheels by hand. That settled the oil into the hub straight off. Been good since and I’m at 680 hours. Surprised your 2501 doesn’t have a dip stick for the front axle. Thought that was standard. Thanks for the reminder though as I should probably change mine again soon.
Thanks for watching, thats a good idea for when i change it out, the standard L series have a fill level drain. Have a good one!
My 2024 GMC truck was 2 quarts low in the rear also. Checked with 5000 miles and pinion gear roaring.
you are correct, have a mx 5800 300 hours, never checked the 4 wheel drive never seen any leaks, until last week the left bearing shelled out when driving and the wheel fell off nice. anyway the axel cost me 458 dollars and the 2 race bearings and seals, another 150 dollars plus the 7.8 quarts of lube, so check are pay the price, if Kubota did the repairs you would be looking at over are close to 1500 are 2000 dollars in repairs
Thanks for the reminder. Just checked my MX and it was full.
Glad to hear that, seems many peope have been at least two quarts low it seems its been mostly the l series and smaller. My M7060 was at correct level
Just did this to my 2 year old L3901. Needed half gallon
Great tip
Thank you… great video… my 2501 was 3/4 quart low…
Appreciate it Ritchie! Need to do an oil change anyway, I’ll check it while I’m underneath.
Thanks for watching Jeff, Let me know what you find out!
Great info mate, much appreciated. I've just got myself a new Kubota and I am dead keen to keep a close eye on grease, oil and other fluids.
Thanks for the heads up I'll definitely be checking my l3301 now!
Thanks for doing this video - I checked my L2501 at 50 hrs and was a half gallon low!
Thanks for watching and glad you were able to straighten it out!
Holy crap 2 quarts…. I’m checking mine first thing tomorrow morning. Good video.
When I bought my L2501, the guru at Coia Equipment told me what was in the front axle and he said to change it to 80/90 weight at the first change.
Thanks for sharing
A good tip - rebuilding that front drive axle would not be fun or cheap.
My l4760 was 2 qts low, total capacity is lil over 6 qts. Thanks for the tip! Lousy PDI....
Mine was full when I checked it after buying it. My dealer is good and sells a tons of 2501s and the guys that put them together do a great job.
Thats great to hear, unfortunately ive heard more people being low versus people at the correct level
Mine was a gallon low! I learned about checking it at about 45 hours of time.
Very helpful. I will check it this week !!! Thank You!!!
Hey Richie. Thanks for showing this! I'm going to check mine also.
Let me know your findings!
Yep. Mine was 2 qts low on my 50 hr service on L2501. Dealer told me very common, come from factory that way, not dealer
As watched, I had to quickly check on mine as the dealer told me to use gear lube Front axle case . (SAE85-,90 gear oil) Then double checked and either or could be used. Front axle case KUBOTA UDT or SUPER UDT fluid* or SAE80, 90 gear oil. I had serviced my B2650HSDC-TLB at 400 hours and I replaced the existing fluid which was gear lube from the factory.
Super little tip - you motivated me to check this fill level - clear and informative - thank you!
That’s what my intentions were! Thanks for watching and I’m happy this was helpful
@@HillsideAcres so I am wondering how to lift the brush hog implement is there a lever or something I need to push to get it to lift some in the back to get it off the ground?
@@twylatwyla7437 brush hog is on the three point hitch. Lift the lever and it will come up
I have a brand new BX2380 ( about 60 hours on it ) and now am very curious to see how much oil I have. I will be checking on this once spring arrives. Thanks for your video ! it's much appreciated !
Thanks for watching, let me know how you make out with it!
@@HillsideAcres Will do ! Thanks again for bringing this info out for people who don't know.
@@KubotaTractorTherapy well what happened? LOL
@@KubotaTractorTherapy one year later in suspense LOL
@@KubotaTractorTherapy I checked mine around that time and it was ridiculously low
Good information to have. I need to check mine tomorrow. Thanks for the tip.
Thanks for watching!
Thank you that's a good reminder I need to check mine I got a 2:45 DT love it
Hey Mike, the storm was much less than the predicted 24 inches! The pusher is great for all the open areas and parking lot we have!
Every 800 may seem excessive but its a good practice to drain and look for metal chips, those angle drives don't like chips and the bevel gear teeth are under a massive load sometimes in 4wd. A couple quarts of oil vs $1k to replace gears, bearings, seals and a cracked housing.
Thanks for the info
@@HillsideAcres Had a Kubota blow up a front drive and farmer next door with a compact deere. Helped him go through his front axle after a sudden dissasembly. Good maintenance for the kubota also doesn't seem to mention pop out the front driveshaft couplers and lube them now and again every couple years else the rust eats the splines, not an overly expensive repair but it breaks when you need it most.
Nice toolbox Ritchie. I should check my fluid also.
Thanks Paul, your branson should be the same style front end and is certainly worth a quick check!
New 2501 4 hours on it and it took well over a quart, all I have is Hyguard I hope that works with the kubota fluid.
My L3130 started leaking at the left front hub. The seal was bad so I replaced both sides. It was a bitch but doable. Had to drain a lot of fluid because it has to fill both hub gear cases also. I don't think the dealer shorted me on fluid because I checked it a couple of times a year. I think driving it on the road for 3 to 5 miles every so often did it. I now trailer it everywhere unless it is only a half mile or so. I think I went back with the Super UDT. Thanks for a good video.
You hit the nail on the head "poor serviceing".
When I worked at a kubita dealer it was our policy to check it before the tractor was sold and check it again at the 5o hour service
I do all of my servicing my self. But the manual should really have checking the front axle at an earlier interval than just changing at 800 hours!
BX2380 here, walked by it this AM and wondered what that front axle cap was for......
Can’t hurt to check it out!
Great info! I will be checking my BX23s before next use!
Cant hurt to check, it seems many have been low from the factory!
Great video. Checking my 2501 tomorrow. Thanks.
Thanks for watching, let me know what you find out!
I just checked my L2501 and just like you said it was low and I only have 89 hours on it thank you the heads up hope to see more of your videos thank you Tony G
Oh wow. Thanks for this video. I would not have checked this otherwise.
Isn’t the larger hole for filling and smaller for checking? When it starts coming out it’s full?
Approaching the 800 hour mark and getting ready to do some maintenance. Not sure where things are at. Wish I would have seen this sooner. Cross your fingers for me.
Thanks dude. Gonna check mine first thing tomorrow.
mine took over Half gal to top it off with only 50 hours new from the dealer
So, I’ve worked with 80w 90 gear lube before, and I’ve used Kubota super UDT. The latter falls somewhere between a typical hydraulic oil and an engine oil in apparent viscosity at room temperature, as I recall, and 80/90 gearlube is on the extreme end of viscosity, almost a grease rather than an oil. Can someone please explain to me how any piece of equipment can call for either of these products interchangeably in the manufacturer’s specifications?
I believe it comes down to the operating temperature where the tractor is located. If you feel more comfortable with a heavier viscosity oil, then use it. 👍🏻
Man, good point. Nice save and it makes sense what you said about the dealer topoff. 🙏’freeze
My 1988 L2850 has a dipstick on the front diff which is nice.
Speaking of maintenance:
Thoughts on the manual often saying, (ex.) "Check/change every 200 hrs or every 1-2 yrs, whichever comes first." The years of ownership seems a little overblown, but how seriously should I be taking it? Thoughts?
It’s a pretty good idea to go by the manual, checking on things like engine oil and hydro more often. A through annual servicing with regular greasing is typically good for most
Hope you serviced that boot on the check valve side!
Great video! I check on my 2501 as soonest i removed a plug it’s started leaking! I’m sure it was full
That wrench drawer is awesome
My 40hp was on it's 50 hour check and i had real trouble getting the service guy in Thailand to check it. so i did it while he was there watching and it took half of a 4.5 litre can and the service guy couldn't believe it .
My 04 b7800 was bone dry, 900 hrs on it, i shutter to think how longs it been that way. Had it since 700 hrs. I was told the hydro trans hydro fluid was shared throughout the diffs.
Thanks for this video and showing how and where to fill.
Thanks man. I haven't got a manuel. My dad passed and with him, a lot of knowledge. You wouldn't know anything about a 64 Massey Ferguson would ya?
Not particularly, but what would you need to know ?
Good morning Sir, you have a very nice AIR FORCE quality tool set 👍🧐 Yes Ben ( K&H tractor ) is a great reference man for sure 😉👌 Yes in deed, any fluids must be check often 🧐👍 OUTSTANDING VIDEO Sir and keep up your OUTSTANDING work both of you Cheers 🍻👌
I love the foam set tools, makes everything so organized! Have a good one Dave!
@@HillsideAcres For us, it is easier to look if we forgot tool inside the aircraft ( Aircraft tool Control ) You too have a great one CHeers
My dealer said to change it at 50hrs. I change it every 200 hours or so. I check it was few times a year.
I'm just about to buy one so thanks very much. Really useful. One thing...why do Americans all talk in future tense? "This is going to be your..." surely it just "is your" :P
I put a clear surgical hose on the end of my funnel that sits in the filler hole made life a lot easier to fill you should try it it really is a great Helping Hand
I have all that stuff but currently in a transition of moving a house building a new shop and barn lots of stuff in boxes lol
@@HillsideAcres you be working out of boxes 📦for a while. Lol
I've got a L3901. I will check it! Thank you.
My 5240 had hydrolic oil in it from day 1,brand new,the left side gear assembly failed.i had to replace all of it,1500.00 bucks in parts alone,now they put in 50w synthetic.
Yes super udt2 is standard from factory just not enough of it
I wish you had showed the front axle gear oil in your video as I could not understand what oil to use.
I used super udt2 it was in the audio. Can also use gear as per your owners manual. I topped up with udt2 because that’s what was from factory and I did not want to mix
Very good advice & need to know 👍🇺🇸 Thank you.
Mine had 215hr on it when i bought it, and YES it was 3 1/2qt low.... Thank you
No problem, I just hate hearing all these stories, I don’t think anyone has commented saying theirs was filled to spec !
I have an M5660, and I am going to check tomorrow Thanks
Thanks, I will check mine. Where did you get your tool box foam??
Box and tools came from Home Depot and a company called foam fit tools makes the drawer organizers
@@HillsideAcres Thank you, I will take a look
You have to check it hot not cold, because oil expands when hot, over filling can cause seals to leak, so don't overfill it cold.
Seals leaking just a little bit will use oil and cause it to run dry, check it about every 200 hours, change it 800 hours.
Thanks for sharing !
@@HillsideAcres I used to run a Kobota mowing 40 acres of food plots once a month, we had front and rear end oil leaks because of sand intrusion into the seals, and that crazy seat they have on them caused me constant back pain so we switched to a John Deere Hydrostat, with Air ride seat, a lot easier on the back over rough hill sides and no oil leaks yet after 3200 hours of operation.
Kubota makes a good tractor but for constant hard usage they just can't beat that Little Jhon Deere or a Yanmar, with Air Ride seat.
@@carrollsanders9376 kubota offers air ride as well! Thanks for dropping by !
@@HillsideAcres They didn't in the L series that we had but the main reason we changed was everytime we crossed the muddy creek, we had to replace axle seals because of sand intrusion on the seals, not a problem in the John deere, if your not crossing creeks constantly then you probably will not have that problem.
@@carrollsanders9376 I dont do any creek driving with my tractors.