VW NB: New Beetle Rear Lid does not open
Вставка
- Опубліковано 14 гру 2013
- When & Where Needed:
*** Raise & support the vehicle safely according to Manufacturer Jacking & Supporting Positions!!! ***
Rate, Comment, Share, Subscribe, Let the Ads play... I'm still paying off my tools!! Tool or Coffee & Donut Donations welcome at my website below!!
fkh161.ca/
Discuss this video in the Subscribed Members Forum:
exovcds.freeforums.org/ - Авто та транспорт
I was trying to go from under it, watching you pop off the triangular shaped plastic piece made it SO easy. Trunk is open!!!!! Thanks man.
Thank you for watching!
Thank you for making this video. I have been studying the wiring diagram and didn't piece together the switch in the latch. You have saved me so many hours of headache. Thank you.
Thank you for watching!
Can't thank you enough for posting this video! You just saved me a ton of diagnostic time!
Thank you for watching!
Thankyou Thankyou Thankyou ,my 2002 new beetle trunk has not worked in over 2 yrs I replaced the actuator a few yrs ago thinking this was the problem ,watched your video and ordered a used one on ebay for 14.99 just put it on and now i can use my trunk :-)
Thank you for watching... nice to hear that my video was of help!
I have a 2006 beetle convertible. I recently closed the trunk with a pile of shopping bags in it close to the latch that I can see in the video here. Is it possible that it grabbed a piece of the bag material kind of like a zipper and is telling the control module that it is open? The switch on the door is flacid and the remotes make a sound inside the car and the lights blink as I do it but it does not unlock the trunk. Any insight as to how I should go about this? Thank you for providing us with your knowledge. Gigi
Sorry about the late reply. If the shopping bag is of thicker material, then yes.
Release action of the motor should still work as it should (I think). Try to get a good grip and pull hard. Maybe a second person to press the button while you pull?
@EXOVCDS Thank you so much. I will try it. In the meantime is the fuse involved? I checked one fuse that I think is central lock and it is functional. Should I be checking another fuse? Also do you have any idea where an emergency pull rear lid release could be in the car cabin itself other than by the door opening as stated here on utube for the newer models? Listen I appreciate any help at any time. I am a bit concerned because my lug lock key is in the trunk and my tire was really low but took air. Thank you for your help. I really appreciate it.
@@Bougie642
Have you seen this video?
ua-cam.com/video/2LYjzcn1wfY/v-deo.html
I have the same problem on my 2007 vw touareg no power from the door switch or the remote i will keep u update going to buy the part Great video thank you.
Your video really helped me.
Just wanted to say thanks
Thank you... kind of you to say.
Thank you for watching!
I appreciate that you made this video it helped quite a bit Thank you
Nice to hear... thank you for watching!
Thank you! I just finished doing the same thing to my girlfriend’s beetle. I bought the $30 part and did everything myself in the same way as your video.... saved me a few hundred dollars by not bringing it in to a mechanic! Thank you again!!!
Thank you for watching! Nice to hear that one of my videos was of help!
Thanks so much for sharing this information I appreciate it ☺️
Thank you for watching!
If all that won't work, I found where the wires go into the lid were broken at the pivot point.
Vw. had hard wires that will break after time they are crap. If you can get some wire that will bend a lot without breaking.
Amazing vid thanks so much for making these
Thank you for watching!
thank you so much Thomas !!
Thank you for watching!
To good persoane made this possible Thanks to you Both ,If I miss someone that to him/Her,As well .
Thank you for watching!
thanks for the great vid
Nick Dama Thank you for watching!
Great series of videos. Can you confirm what is the fuse for this circuit? I have a new latch and actuator and it still can not get the trunk latch to lock/unlock via fob or switch in door. Thanks
Year / model? So that I can look at a wiring diagram.
I'll have to try replacement of the trunk latch. 2007 volkswagen beetle hit the fob or trunk release on door, truck opens but not fully release the lock. Just today the light on dash stays lit as if truck isn't locked although it seem to be completely shut and its causing the alarm to go off after locking the car.
Just not aligned correctly by the sound of it.
Hi Thomas, any vids on the adjustment of the rear hatch? I moved up both rubber stops but needs more at the catch. Thanks, Dave.
No video yet sorry.
That would be an easy one for you. Also a friend of mine is struggling w his door alignment! Thank, keep up the great work, Dave
Thank you very much.. I followed your steps but I didn't change the lock only there was tartar on the socket
Thank you for watching!
Great video, thanks! My wife's 2003 Beetle (UK) has a "reluctant" boot opening - it just opens a little then catches so you can't get it any further open - you have to activate either the remote or the door switch a few times to get it open. Do you reckon this would be the latch or the actuator?
Best way to know is to remove the anel and watch things in action. You can disconnect the actuator from the latch and open it manually to see if the latch behaves differently.
Thank you for watching!
Happy New Year!
Hi, I’m posting this for other people as I see this is a few years old now. I had a boot that opened the latch OK with the remote but it wouldn’t with the unlock using the button on the drivers side. I saw a post telling me to look for an 8mm bolt on the hinge mechanism, and in wind them out a few millimetres. This solved my issue! When I looked at them, one side was 2.4mm out the other 3.2m. I unwound them to about 4mm on both sides. Works perfectly now. It’s down to the gas struts losing some power, this adjustment just gives some resistance and helps the strut. Just do a few turns at a time. Hope this helps!
What is the part number on that latch? I'm finding several, they all look the same? I have a 2013 2.5 and just recently the hatch doesn't want to open.
Ruben Robles Part numbers are on pretty much all parts that are mounted to the vehicle... have a close look at yours and I'm sure you will find one. If you still can't find it, phone your local VW Dealer Parts department and give them your VIN number.
Do you know which is the power wire to all the units in the hatch? So I can test to see if it's even getting power ?
Thanks
A wiring diagram will tell you that.
Any thoughts on how to do this on a Convertible? there is only an access hatch from the back seat.
Carefully... whatever it takes. Have not yet had the chance to find out how much of a pain that setup would be.
Hi, I have a 2003 Passat Wagon. The Trunk is shut and does not open with the key in the keyhole, or by remote or through the button on the driver door. When ever I press the remote, Central Locking fuse blows out. Do you have any idea how to open the trunk panel from inside the car. would that be similar to the beetle? . Please help. thanks,.
Did you get my message?
The dash light says the boot hatch is open and it trigers the alarm on the car. This could be as the relay is in the latch the last time the boot would not opern I found two broken wires to the wire plug for the latch when they were resoldered everything worked fine. Try to tease the wires out of the plug I found they were broken. If you damage the insert or can't solder the wire because its deep in the plug you can find the inserts in computer motherboard wire sockets. Maplin used to sell the single pin wires don't know where to get them know but I have 20 left just in case it happens again.
The micro switch in the latch is a common failure item. The Alarm module looks for a signal from that switch... corrosion can interrupt the signal and the alarm module will think the trunk is open (when it is not) setting the alarm or causing the waring light to stay on. Replacing the latch and insuring that the connector is not corroded, should take car of that type of issue. I have also seen bad connections / corrosion at the wires in the brown connector at 2:50 (under the H of the watermark) that caused trunk opening issues.
I'm having the same problem with my 2002 VW Beetle ,I was wondering is there a key entry on the trunk under the VW emblem on the trunk
Some have it... this one does not.
Thanks for posting this video. Something that wasn't clear is why the actuator started working when you replaced the latch. Is the power to the actuator controlled by the latch some how?
David Carroll The latch sends an open / closed signal to the central locking module. If the module thinks that the trunk is already open (because of a faulty latch) then the module will not send a signal to the actuator.
DOH! I just now saw you included an explanation about the "faulty micro switches" at the closing of this video. Sorry for missing that.
So, my situation is very similar to the one in this video. Neither the trunk release button on the driver side door or the key FOB releases the trunk. I do hear a clicking sound similar to the blinker / hazard signal and see the rear lights flash - as shown in your video.
I ordered a new OEM trunk latch thinking that was the problem for my daughter's 2010 VW Beetle Convertible. However, the actuator did not respond when I plugged in the new latch and set it to closed position. All the symptoms were the same.
I did notice that the new latch body was about a half inch shorter than the original faulty latch. However, everything else about the new latch was identical to the one in the car.
One difference between your video and my situation is I was able to use a multimeter to see that signal is sent to the plug for the actuator motor when pressing the trunk release button on the remote. It seems that power is only sent to the actuator plug when the latch is in the closed position.
I ordered a new actuator to see if this would resolve the problem. Unfortunately, nothing changes when plugging in the new actuator and new latch. I've also tried using the new actuator with the original latch.
One thing I noticed is I'm unable to get a signal on the multimeter when testing the plug for the latch. I was able to verify continuity on this latch plug, just no voltage reading.
Something else that is strange is while I am able to get a voltage reading on the actuator plug, I am unable to get a continuity reading on the actuator plug.
At this point, based on your explanation of the "faulty micro switch", I get the feeling the replacement latch is also faulty.
Any thoughts you can share based on my details would be greatly appreciated. I wish there was a way I could send you something for your expertise.
*New Off Brand Actuator:*
www.oreillyauto.com/detail/b/dorman-oe-solutions-3387/body---trim-16771/trunk-lock-actuator-motor-15799/899e127fd579/dorman-oe-solutions-blade-terminal-type-actuator/746405/4255887/2010/volkswagen/beetle?pos=0
*New OEM Trunk Latch:*
www.ebay.com/itm/1998-2010-VW-Volkswagen-Beetle-SEDAN-Rear-Trunk-Latch-Assembly-GENUINE-OEM-NEW/321673407792?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649
I had similar problem with my 2002 New Beetle. Bought both new latch and new actuator. New latch did not activate with original actuator. New latch did not activate with new actuator. Then decided to test original actuator with a 9 volt battery after I removed it from the hatch. The original actuator did work when it was hooked up to the 9 volt battery so it was still good. I then reattached the original actuator back in the hatch along with the original latch. Amazingly, the hatch now opens both with the remote and the button on the driver's door. I think that testing the actuator with the 9 volt battery somehow "kick-started" the actuator to work again. I was able to return both the new actuator and new latch.
I have found bad connections (corrosion) in the wiring / connectors that affected the voltage supply. The motor may still have "worn spots" that may cause it not to work again in the future.
I seen a video on a beetle that said if the drivers window does work then the hatch won't open is that true thanks
I haven't seen that video. A wiring diagram should be able to determine if driver window operation is a factor. If rear lid button signal goes straight to comfort control module... then driver window operation does not play a role. If rear lid release button signal goes to driver window module first and then to the comfort module, then maybe.
you rock! thanks
Thank you for watching!
Hi, I have the same issue on a vw beetle cabriolet 2008, lights flash when boot release button is pressed and held. I have changed the actuator, and tried another second hand boot latch (from car yard who said it worked) and no change unfortunately. Tested electric connection points with boot mechanism with a volt meter, all reading around 10 volts. No obvious signs of broken wires anywhere else. Any advice would be much appreciated.
I recently had one that had bad connectors / corroded pins at the connectors. Make sure that all connectors have clean pins / contacts.
Just a thought but it could be the Convenience Control Unit. Water commonly gets in here causing alsorts of issues with minor things on the car. On the RHD model it is fitted right up behind the dashboard on the drivers side. Water comes in on a standard model so I imagine a soft top to suffer this issue even more.
My 2008 convertible beetle has the same problem. My back window is not sealed good and water leaks in. +Hey Micky, could you help me on how to fix this? Cause reading your comment it makes perfect sense.
I'm having the same issue with my daughter's 2010 VW Beetle Convertible. There was no change in what everyone here is describing after replacing both the actuator and trunk latch.
I'd love to know if anyone here has any updates to their situation.
If no one here has resolved this issue yet, you can follow my progress in a thread I started with Thomas a few days ago:
ua-cam.com/video/bO7eYOcOlv4/v-deo.html&lc=Ugw9KMzZj2i6ZbKyVth4AaABAg.8h-mWrICkAY8h5cJQsbOjg
Good Job. Thx. I have the same Probleme
Thank you for watching!
@@EXOVCDS you're welcome bro 😁🤜🏻🤛🏻
This is very helpful. Is there a way to troubleshoot this if you don't have a replacement latch to test with?
My trunk won't open. Key fob remote causes rear lights to blink, but no trunk latch motor activation. The trunk switch in the driver's door gives no reaction at all.
You can attach a "noid light" or test light across the harness plug for the motor and look for the light to activate (indicating control). Check all connectors for possible corrosion... which can cause resistance that won't allow the motor to operate. Using a scan tool, you can check for related fault codes and view / verify "input signals" (should be good since lights flicker) as well as door / trunk / hood open & closed status. With all doors / trunk & hood closed... the alarm should beep when you lock the car... if it does not, then the comfort control module is "waiting" for one of them to close (thinks that something is open). The driver door button won't seem to do anything, IF the comfort control module thinks that the trunk is already open.
@@EXOVCDS thanks a ton!
I finally got to check individual connections and found that the female 3-pin connector from the end of the wiring harness to the latch mechanism is corroded. I already ordered a replacement latch (as the male 3-pin connection is also corroded) and will now need to source the small connector and replace it as well.
I will let you know if this works.
Thank you for the update!
@@EXOVCDS I just fixed my trunk on my 2002 Beetle Sport.
It was not working at all. The driver's side switch and key fob remote were useless. (I could still open the gas tank lid by the electronic door switch.) The key fob caused only the brake lights to blink briefly. No actuator noise could be heard. All other remote key functions were okay. No dash warning lights. I could lock the car remotely, one horn beep, and the alarm did not go off.
I took a look. There was severe corrosion between the latch sensor and the three prong connector at the end of the wiring harness, so I cut the connector off and cleaned the male end connections that are housed in the latch. I then redid these connections with alligator clips of similar gauge. Nothing happened. I cut off another centimeter of wire and tried again. No result. I removed the alligator clips. The wires are dead-ended for now as I am waiting for a new plastic connector.
I took a look at the remaining cables and connectors. The all looked good. I figured the actuator was dead. I unplugged it and checked it with a 9V radio battery. It worked fine. Then I replugged the connection. Suddenly the whole latch system worked perfectly both with the remote and with the switch in the door panel.
The funny thing is that the trunk latch itself is totally disconnected now. There is no wiring going to the microswitch in the latch.
@@tromboneJTS Strange... that's why I hate electrical work! =)
now I can fix it myself, tired of waiting on my husband, thank you
Let me know how it goes.
Very good!
Thank you for watching!
I have am 2005 convertible bug. but trunk wont open even pulling up on the copper lever manually. Thoughts?
Trina Jeffryes I'm a visual person... need to see what you're talking about. Send pictures to fkh161@fkh161.ca or post a link here.
sent. thanks.
Trina Jeffryes You'll have to try and get a look down in there... usually what happens is that a piece of plastic breaks off & falls into the latch linkage, which hinders full movement of the release lever. Use a mirror to look down into the latch mechanism. Look for something that is obstructing the movement (move the lever while looking inside). If you don't see anything that is getting wedged.... force it. If the trunk hasn't been opened in a long time, it could just be stuck to the trunk seal. In that case, give the lid a good push while holding the release lever up.
Is it possible to change only the microswitch or is it necessary the whole latch part?
+Roberto Galván Ávalos The micro switch in the latch can be changed separately.
+Thomas EXOVCDS
My VW dealer sells the entire piece, thanks for the info
+Roberto Galván Ávalos You are better off getting a complete latch, as the plastic liner around the inner latch always comes off with age and can jam the latch / cause issues.
My 2010 Beetle is having trunk issues. but It's the remote I believe. I have to be directly behind the vehicle in order for it to pop. If there is any obstacle like a window or a door it will not pop. The remote has a new battery. Any ideas?
I don't know where the antenna / receiver (for the FOB) is... or if that is the issue. I would check the comfort module for fault codes (or a full system scan) to see if there is anything that might be of help in troubleshooting.
Thomas EXOVCDS ok thank you.
Im stuck with mine. I own a 2008 VW convertible beetle and my trunk used to work just fine. My back window is not sealed good at all, water leaks in every time it rains. My car just flashes the lights and doesnt open. I can manually release it but i am not able to use my trunk. I assume the leaking issue did something. Please help me on what I can do
Could be related to wetness... take things apart and inspect.
I have no clue how to take the trunk apart to inspect or where to check. Any ideas as to where I could bring it?
Octavia Wilson A repair shop in your local area that is familiar with vw's?
question and hope to help me..
In automatic gearbox .. should take off center console to replacement slide cover or what to do?
Year, make, model, 4spd auto, 6speed auto, tiptronic?
@@EXOVCDS vw new beetle 2005 1.8t AWU 4spd auto
@@Folz30 remove the handle. Slide the spacer up and then pop off the square cover.
volkswagen.7zap.com/en/usa/beetle/be/2005-271/7/713-713010/
@@Folz30
I assume that this is what your shifter looks like. If you post a video on your channel, I can see what version cover you have.
@@EXOVCDS I will upload a video today and make a reference for you.. Thank you very much, you help us a lot
Do you know how to put in the backrest seat release handle on the front side seat?
Shon9tilR the handle should just pop off / on.
Thomas EXOVCDS I tried taking one off and it doesn’t pop off.
Shon9tilR The handle looks like this:
i.ebayimg.com/images/g/OowAAOSwFnJZeBY0/s-l300.jpg
You can see the little metal clip at the end of the handle. The clip bites into the metal lever inside the backrest and into the handle. Grab the handle as best you can and pull. You might have to wiggle up & down to get it to break free. Once off, make sure the new handle has the metal clip In the tip. I like to keep the clip sticking out a little... then line the handle up with the lever inside the seat and then push the handle into place.
Thomas EXOVCDS Thank you so much!
i have the same symptoms - when you press on key or pull the boot release it only makes a sound but nothing happens. could it be anything else or do i just buy the same part as you did. i didnt quite get the testing with bulb - it there is no electricity going to the mechanism, wouldnt the problem be before it? Ive seen other people replacing the actuator - how to test which part i need?
If the trunk does not open, you'll need to open it like I did (remove the panel and move the linkage with your hand). Once the trunk is open, you can check what is working / what is not. If you hear something moving when the remote button is pushed, then the "signal / control" to the motor is OK. Something is either stuck or disconnected... not allowing the motor to move the linkage. Start with taking the panel off and checking all the linkage... sometimes it's just a matter of lubing the linkage with WD40 or similar, to free things up.
its my friends car, she has some sort of string system with which you can pull it open from interior and also the plastic cover is off already. ok ill check visually when i can
Just checked with multimeter - there is 12v going to actuator when boot release is pressed. but actuator isnt moving or making any sound. Must be the actuator??
Harcix Did you measure across the two wires? Is the actuator extended or retracted? On some motors, the polarity changes.. meaning that the actuator is used to open the latch as well as lock it. Some motors will extend automatically some need the reverse polarity. If you checked for power by placing a test light on one wire at a time (ground of test light at body), check across the two pins. It could be that there is a broken wire. If the wiring is ok, test the motor on a bench with small jumper cables... see if you can get it to extend & retract. If it works on a bench, then the micro switch in the latch might be bad. If it does not behave correctly on the bench, then yes, might need a motor / actuator.
I checked only those 2 wires and also 2 out of 3 wires going to the latch. Latch should be ok as it shows on dash if its open and it gets 12v continuous, also - when latch is open, the actuator doesnt get 12v. Only when latch is closed and release button pressed it gets 12v (and polarity on multimeter didnt change). Actuator is in retracted position. I checked across the 2 pins only as i didnt want to short something by touching body.
Wonder if this is what’s wrong with ours? The trunk won’t open with the switch or the key
Don't know... have a look. Let me know what you find.
Hey and thanks for all your vids, they're great help.
My problem is the boot opens with the key, but the switch on the door doesn't work at all. In fact the switch is completely dead, with no even a noise when pressed, which makes me wonder, it could be a power problem.
Is there a dedicated fuse for this motor or just one shared with other functions?
Thanks in advance and keep those vids coming!
Francisco Caballero Sorry I forgot to reply yesterday... What year? Model? I'll send you a wiring diagram.
2.0 petrol year 2000. Thanks bud!
Francisco Caballero See if this will help: fkh161.ca/VW/NBRearLid.pdf
Great, thanks again, will have a look tonight and see if I can find a solution.
Also read somewhere, it could be one of three things, the tailgate button itself, the tailgate lock microswitch or even the actuator??? A lot of money to spend on three things, when it does work the old school way, by just using the key, lol.
Francisco Caballero Yeah, eliminate one after the other and you will find the fault. Start at the button in the door. If the CCM thinks that the lid is already open, then the remote & the button in the door will not do anything.
where did you buy the latch from.?
My local parts store that we deal with.
Hate to bug you again but I can't find any videos on the spoiler light staying on the dash.
I cleaned the wire harness for the spoiler motor while the battery was connected like an idiot and now my spoiler dash light stays on and my sunroof no longer works. I checked all the fuses. After checking the fuses I tested the spoiler switch and sunroof switch for power they're not getting any. Any insight would be appreciated.
PS you should do a short video on the load adjustment bolts for the trunk. It took me a week to figure out why my trunk was not popping open all the way.
turd polisher I'm still on vacation and don't have access to wiring diagrams until next week. Send me a reminder message next week and then I'll be able to help.
ok thanks.
Thank yuo very much
Thank you for watching!
Would a bad trunk latch cause this?
Vance Durham Could be a hatch adjudtment issue. With the hatch raised, can you latch the latch and then check if it opens fully when activated with the remote?
Canada kicks ass.
LOL... thank you for watching!
Hi i slammed my boot down on my vw beetle 2005 and now i cant open the boot nor the fuel lid ive tried the switches in the car the dont open any thing .i,ve tried the fob as well and that dont work as well now help please if you can
Not what slamming could have done, aside from popping linkage loose... but fuel & boot at the same time, hmm. You'll have to see if you can get at the inside panel from the inside, pop it off, open the lid manually and then inspect components & wiring.
Here's a wiring diagram: fkh161.ca/VW/NB/NBTrunkWiring.pdf
Use a test light and check power & grounds.
also to remove it do you use hexagonal tip?
Just about to start work... I'll get back to you later tonight (west coast pacific time).
To remove what?
to remove the latch mechanism. But i think i read its a torx (just not sure what size)
Harcix The latch is held on by 10mm nuts.
I've replaced the latch on my beetle but still don't want to open. Is a fuse or something else which can be damaged? VW New Beetle , year 2003. Thank you.
Do the lights flash when hitting the remote to unlock the trunk?
Did you check / verify both "power & ground" wires are ok... follow them from the motor along the harness and check for corrosion / bad connections. When you lock the vehicle (all doors, hood, trunk closed), does the horn beep once? If not, then it is waiting for something to close (thinks trunk or one of the other items is still open). Using a scan tool like VCDS or OBDEleven, one can "view" door, hood, trunk status to see if it is open or closed. One can also use a scan tool to see "button activation".
@@EXOVCDS When i hit the remote to unlock the trunk, the lights flash, even when i try to open the trunk from interior button. When i close the car, all the doors and even the trunk is closing. The horn is not making any sound, but even before having this problem with the trunk the horn didn't made any sound when the car is closed. I will try to check the wires, or perhaps, the latch which i have bought is damaged as well... I will try with a new one.
@@EXOVCDS I get 1.3 to ~1.4v to the motor when actuating the trunk. Is there a faulty relay ?
@@Brisou394 I'm pretty sure that there is no relay. The Comfort Control Module is what triggers the motor. Depending on how / where you are checking voltage, you could be seeing a lower voltage due to a "voltage drop" (bad connection, not with meter, but with wiring being checked). If you are checking across the unplugged motor connector, use a body ground to recheck / confirm power feed voltage. If voltage is better, check the ground side.
@@EXOVCDS Thanks for helping, I well cleaned the electronic part of the latch, but the trunk isn't light nor the dashboard when I open the mecanism manualy..
So I get 11v from both NU and NB cables going to the latch and both browN cables are the same, they are 800k ohms to the car chassis.
The motor also works with 7volt from my power supply. So the car knows it needs to open the trunk with flashing turn signals/lights but nothing happens.
And I still get same bad voltage to motor..!
My 2012 beetle trunk stopped opening. Solved by holding key fob button instead of usual short click push.
Trunk operation via fob usually requires a longer press of the button... compared to door buttons.
@@EXOVCDS I’ve been opening my trunk for 11 years with a short press. same press as doors.
@@uncleGlen sorry, I guess it's my Mom's Passat remote then. It's the VW that I deal with the most and that's why I have a longer button hold in my head.
@@EXOVCDS forgiven. Update: One pssst of WD40 and I’m back to short click success.
Hello thank you for your great video, I have a question, what's the number part of the piece I need to change this part , could someone help me?
It's best to order parts according to your vehicle identification number / VIN. Go to a VW dealer and get the part number from them (if you want to look for the part online) or buy the part from them if they have it.
if i use the door button, mine only opens if someone pulls on it
Check the adjustment of the latch / release motor.
@@EXOVCDS Do you have a video for that?
@@roseofsheryn Sorry, no. Also check the hatch / lid stops. The rubber stops / buffers help lift (when adjustment is correct) the lid once the latch releases.
Dankeschön
Thank you for watching!
We have a VW beetle and also trouble with our trunk. Sometimes it opens, sometimes it doesn't. I found the solution! We don't use the goddam trunk!!!!~
Very smart.
How did you go from no signal to changing the motor and getting signal?
4:09 a good used "latch" was attached. The vehicle now received a "rear hatch closed" signal. The car will not send a signal to the rear latch motor, if it thinks that the hatch / latch is already open.
Man you just saved a Greek beetle . . .
Thank you for watching!
I hope this will help some of you. My wife just bought a 2002 Volkswagen Beetle and the trunk wouldn't open. The only way I could get it open was as follows: First start the engine (just turning on the ignition won't do it, you must start the engine. Now with the engine running use the trunk button on your door. Presto, that's all it took. Good Luck!
+buddybleau Thanks for the info!
+buddybleau
That's wayy too easy to ever work for me.
Mine (1999 VW Beetle ) just bought it yesterday for $1,000.00 runs great K&N Cold Air Intake new tires...cool sounding muffler on it too. 5 speed Manual....actually has a ton of power. but the Hatch won't budge....gonna have to tear is apart I'm afraid !
The random letters on the screen are very distracting they're right in the way of the action
I have decreased the letter intensity in later videos... they are only bothersome if you keep thinking about them. While watching the video, think about what is being done... the brain will ignore the letters if it is busy thinking about what is happening in the video.
So you wasted a lot of time taking off interior panels, there is actually an emergency release that is hidden that would have really helped. On the inside is a slot that by sticking the key or screwdriver you can release the door from the inside
Yup... I missed that.
Kind of concerned about 35000 views of trunk latch repair on a vw. WTF - Not yo daddies vw I tell you that.
Not to worry... it's the same guy watching it over & over until he gets it right! LOL
Thomas EXOVCDS that would be me...lol
hey bro is there a fuse for the trunk as well..?
Year, make, model? I think it's on the same fuse as the fuel door. I'll check once I have your info.
You have the easiest model lol. Try that on a convertible 😂😂