15yrs ago you would have to get a 350Z or something and the STI was better, but now I think your in the funner and faster car. Also has nice interior too
Yup, I got tried of Subaru quality issues and tech's here in the US not being able to properly work on them thus causing more issues. Sold the STI and got a Hellcat.
Silicone sealer is a red herring and not the reason for failures, this video continues to spread misinformation regarding the GR86/BRZ. These FA24s are suffering from a combination of oil slosh/starvation, under-filled oil capacity from a shallow pan design, and high oil temperatures combined which is a recipe for engine failures. As long as a temperatures and oil levels are kept in close check with a proper oil pan/baffle/viscosity and cooler setup, these engines can survive reliably and that has been seen with the GR cup cars if you read closely about the engine "failures" they have had on track.
I 100% agree with this… I have been doing lots of research and spoke to the owner at “The86shop” in QLD Australian. He has raced 86's for over ten years and is very knowledgeable on the platform. He recommends running a Motul 8100 power 0w20 with an oil cooler and doesn’t run a oil sump baffle as production racing series doesn’t let you. He has done multiple Bathurst 6 hour races on both his and other customers 86’s plus other race meetings and has never had an engine failure which I found extremely interesting as everyone says you need to run “thicker oil” and a sump baffle.
@@Mad_Rass.mk6gli the aftermarket is already figuring out non-intrusive, bolt-on ways to prevent oil starvation and high temps, they're just not available to buy yet. With time, solution will only get better and more refined.
I believe that oil pan baffle does little or nothing to control oil starvation issues. I autocross my GR86 and overfill the oil 1/2 quart and change the oil often.
the issue is only on consistently tracked brz and gr86 on right hand turns with high g's extended turns that cause this. On the street only no problem.
@@tirgod100 the cars are still new. and the issue does not affect 90% of GR86 and BRZ owners. it has nothing to do with reliability. the engines are actually very reliable. it is just a fault that shows itself in a specific setting, lets not act like they have not had things like this before. I do think they should have made a new oil pan and pickup design, offer current owners a replacement...
@@max_coast No You don't have to watch all of Misha's videos on this vehicle. After its purchase, the community had warned about the risks on this engine. Therefore, Misha and the technician had tried to eliminate as many risks as possible, by upgrading the lubrication and taking the opportunity to eliminate any unnecessary RTV "at this location"
It is irrelevant that the oil pan was opened earlier and the RTV was removed. The RTV is all over the engine, even if the RTV from the oil pan gasket is removed, it will still show up. It is not because the oil pan was opened earlier.
yes, there is an obvious sign of who ever popped that pan, had no idea what they were doing.. its very clear what happened here. plenty of people are building fa24s without issue...
This is an inherent design flaw with flat engines, isn't even subaru specific, this is exactly why porsches use dry sump ($$$). bigger displacement over gen1 means that oil is getting trapped in the timing cover causing a pressure drop on high G right hand turns, conditions you're only ever seeing on a track fortunately. the excessive RTV is beat to death at this point and as far as I know there are zero confirmed cases of engines being blown by excessive RTV. Subaru redesigned the pickup to have 5 sides, and says apparently there isn't enough RTV to clog the pickup. Even if that's totally true, the jelly seen in your pan is concerning. the oil pressure issues have been pretty well documented by 900brz. it's momentary, but after it happens enough times the engine could go at any point, like yours. seems like you need to upgrade the oiling system if you want to reliably track these things, which is a shame with how they market them. I don't track mine so it doesn't bother me but I'll likely have the pan dropped, inspected, and replaced with the correct amount of RTV as soon as the warranty is up.
Interesting 🤔 I have been doing lots of research and spoke to the owner at “The86shop” in QLD Australian. He has raced 86's for over ten years and is very knowledgeable on the platform. He recommends running a Motul 8100 power 0w20 with an oil cooler and doesn’t run a oil sump baffle as production racing series doesn’t let you. He has done multiple Bathurst 6 hour races on both his and other customers 86’s plus other race meetings and has never had an engine failure which I found extremely interesting as everyone says you need to run “thicker oil” and a sump baffle.
@@enzSawith the right parts you can install a dry sump kit on any engine but unless you really beat it on a track it will never be worth the investment. It's really expensive.
Its not about RTV in FA24 its about oil not going back to sump and pump has nothing to pick cuz oil stays in heads bigger sump can help ,problem for Misha here is that this happened on slow drive with no hard G corners and that is very hard to explain how engine can blow it self in this situation why engine had no oil pressure at 80kmh on strait road on drive to gas station.
Maybe sludge was pickup up hot on track, cools near the pump when parked and when it warms up again a it comes loose as a clump and clogs the pump or gallery, starves the engine.
I've been a cylinder head machinist for 17 years and this a classic Subaru thing. The amount of silicon they use I ridiculous and they also have a tendency to have valve guides drop when overheated.
@@MrAchilles113 no, the silicone is not the issue and this had been known for a long time now in the gen2 community. the issue is the oil pan / oil pickup design when going thru a hard right hand turn. the car loses oil pressure. you can get an accusump wich is a canister that hold pressurized oil and delivers it when the engine oil pressure drops. it is much cheaper than a new engine or a dry sump. it would probably prevent the majority of oil pressure related failures
the silicone is not the issue and this had been known for a long time now in the gen2 community. the issue is the oil pan / oil pickup design when going thru a hard right hand turn. the car loses oil pressure. you can get an accusump wich is a canister that hold pressurized oil and delivers it when the engine oil pressure drops. it is much cheaper than a new engine or a dry sump. it would probably prevent the majority of oil pressure related failures
@@tone3560 right. I'm not saying the silicon is the culprit, just confirming that they do use a copious amount of silicone. I know they suffer from oil starvation under extreme loads.
Per ChatGPT “Silicone RTV (Room Temperature Vulcanizing) does not melt after it has fully cured. Once cured, silicone RTV can withstand high temperatures, typically ranging from 400°F to 600°F (204°C to 315°C) depending on the specific product. Instead of melting, silicone will eventually degrade or harden when exposed to temperatures beyond its rated limits, but it won’t revert to a liquid state like some other materials might.” 4:19
what happens if you through cured RTV in a blender with oil? Is it possible pieces broke off and were shredded throughout the engine until creating that paste?
I've seen that jelly/sludge cause a failure on a new built engine. They over packed the oil pump with assembly grease to help build oil pressure on first start, drove 50 miles did an oil change, drove 200 miles did an oil change drove 500 miles did an oil change every time the filter was cut open and inspected an was clean. 1000 miles in rod knock started they pulled the pan and it was exactly like that slimey grey goo in the bottom.
right, i dont get how these youtube channels keep pushing this nonsense... its totally click bait because they didnt do their due diligence, and then blame subaru.
@@nastasiaj yes, RTV is not the issue. the car drops oil pressure on hard right hand turns. if people just got some type of accusump it would prevent 90% of engine failure instead of playing the lottery-
They still haven't solved the oil starvation issues...smh. I've always wanted a brz/gr-86 for the platform but this a big turn off. I would have much preferred a version of the M20a or A25 toyota engine. Inline is generally just proven and reliable.
Those two engines are Atkinson cycle engines specifically designed for efficiency and emissions only and are meant to be ideally paired with hybrid systems. In non-hybrid cars with those two engines, they are completely gutless. As for the starvation, the aftermarket will find solutions with time and research and as soon as people stop thinking silicone sealer is a problem.
@@antoinedoinell its a shame as the issue has been known since 1990's.... subaru have done nothing to stop it. They should have at least made the performance cars woth baffled sumps !
@@TML34 testing has been done that there arent really any downsides for the fa24 and it REALLY helps oil pressure loss which is the main killer of these engines.
@@TML34 you are worried about foaming, and that doesnt happen till prob double the required amount of oil in the pan. a quart over, hell even 2 quarts over is totally fine. ua-cam.com/video/VaTbfvzNbxQ/v-deo.html
RTV is not the issue... it is right hand turns. and there is an easy fix too, people just like playing the lottery instead of spending a few hundred bucks on an accusump
We run 2 stock GR86's at the NurburgRing during tourist weekends. They are also used as daily drivers. No issues yet, but we don't drive as fast, or do as many laps as Misha. I was waiting to see what the failure was as we are considering changing cars next year. Its disappointing to have to worry about possible engine failure.
@@saitabit baffle plate is not a big partitioned crankcase (what it should have had, but not yet in production) 😉. 🤔I don't remember the grade of the oil, but he was switching to a slightly higher grade, to try not to have this problem... he talked about it on his videos
I highly recomend looking into an accusump system, it delivers oil when whe oil pressure drops to save the engine from failure. the cars lose oil pressure on right hand turns. it is not that expensive either.
Seems that 2nd gen GR86/BRZ are more susceptible to oil starvation issues in general. And not just due clodgs of excess sealant. FA24 more pleasant engine for daily drive, but for track use with high long side-Gs, old FA20 seems more resilant
All subaru engines are subject to oil starvation... there is so many videos on how to fix these issues.. the best being on MOTOIQ... people just refuse to educate them selves and think they can fix anything.. Subaru engines are finicky, but when done correctly can be very very reliable, even at high HP.. The FA24 in the wrx holds upwards of 500hp on stock components, with just bolt ons and e85.. the issues are the same that have always plagued these engines, track use without proper setup.. a pick up/baffle etc have to be used.. the cases puke oil, and its well documented..
@@juanticimoits no excuse though, Subaru have known about these issues for 30+ years and not fixed them. IMO there is no way to fix these issues without an Accusump or Drysump. Baffles do not work in the EJ, the oil capacity is just wayyyy too low. The EJ needs like a 8 litre sump, not 4.4. 4.4 litres is enough for a 1.4 or 1.3 engine , not a 2.0 turbo.
all you need is an accusump. people jsut dont want to spend the 400 something bucks to get one. what a shame that such a simple thing could save 90% of the engine failure on gen2 cars
@@bigkaswrx8115 obviously. but shit happens and every engine nad every car has flaws. the oil pan is just bad. unless someone makes a completely new oil pan that eliminates the oil completely sloshing out of the oil pan and away from the pickup, an accusump will be you best option. just get the biggest one you can I guess :D
I had a '99 2.5 Legacy back in the day. Great car, loved the handling etc. One day, as I was pulling up to the house, the engine just stopped dead and wouldn't turn over. Crank seized. :(
it is asembled by machines. so RTV is simpler. still RTV is not the issue and this has been known for a while now. it is hard right hand turns on track. there is a simple fix too, just get a fucking accusump instead of playing the lottery
Wait until you guys find out the pistons on the HKS pistons are the exact bore as OEM so you can’t bore out the cylinder walls in the event of damages, you have to use oem new cylinder walls or pray yours don’t have damage. This is straight from HKS for their specs and IAG as far as potential machining issues lol
I still don't understand why you didn't upgrade at first place engine if you are know you will be tracking that car, as minimum upgrade oil pan with baffled sump and oil pick up which would prevent that issue for time being
I believe it's because he did not expect that, or conspiracy theory he did that for the content haha. Also apparently he tried to seal it better than subaru did
@@alphaenterprise2232 I wouldn't expect that too, but I assume he built it as track car? If yes then I would build at least forged engine for track car with 11mm or 14mm headstuds just in case Baffled sump and oil pick up is literally minimum upgrade for that car, if he does more drifting or he exceeds that then dry sump it to be on safe side, over here in UK people run on their EJ207 or EJ257 baffled sump with uprated oil pick up and they do a lot of sprint series and track days without any issues, dry sump is if you are loaded Hopefully won't end up as Donut media and their Subaru High and low car builds🤦
I have no idea why people track the cars knowing there is an issue, and that there is a clear and simple way to fix it. get a fucking accusump. fuck the oil baffles, fuck scraping off the RTV just get an accusump. cheap and easy to install too
@@turbo________ a few people have data logged a bunch of runs on the track and even with accusump on long right turns, the engine oil pressure drops... and thats with bigger pan and baffles too. I wonder how porsche does it at this point lol
@@NimaSomeh yea I have seen that. still it is the best you can do right now. A bigger canister would help or maybe a dual canister setup so the 2 individually smaller canisters fit under the hood. porsche uses some kind of a dry sump system from what I know
These cars loose a lot of oil pressure during sustained and harsh right handed turns. From what I’ve seen from people who race them, an oil sump, the right oil (a 40 weight oil for racing), a baffled oil pan, and adding an extra .5 qt of oil will reduce the amount of pressure loss significantly.
why i got a built engine in my subaru was because my engine blew up leaving a gas station parking lot at 15 mph. lol no high revving or launching honestly i shouldnt have gotten an IAG engine and rebuilt it but i did. the same issue is inevitably going to happen again.
Problem is, the quality of gaskets and sealing rings is going downhill at the moment, even for OEM parts. So they are sort of promoting siliconing up things to cover for the crappy gasket's you are getting. And as another UA-camr said, this is what will kill the internal combustion engine... Crappy unreliable parts, even when you pay good money for it.
Holy shit! The RTV issue isn't just specific to the oil pan, it extends to the entire engine assembly? That's it, my last 3 new vehicles were Subaru's.. next one won't be.
Stroker kits aren't really about peak power but more torque... so although number gains won't be much you could make 100hp like 2000rpm lower maybe but peak power lower
My first gen engine also died on the street just by idling in the parking lot. Very strange stuff. So it’s something that affects both gens. Curious if they will continue the way with the gr yaris engine in the next gens as they already racing a gr86 on altenative fuel with that engine.
Seems like most folks are overfilling by .5 or 1 qt and are fine.. Granted they're not on the Ring, but just 'regular' tracks.. If you're really concerned.. should've gotten an Accusump.. maintains pressure in the oil system no matter what.. $800 USD
Normal amount of sealant from factory not the cause of failure... maybe oil starvation due to oil surge on track running Check the oil pump in the front cover.... How are the cams and cam caps
Here it would be worth thinking about building a new car . This engine is...The problems were mentioned several times in the chat . I would really try maybe a different car / engine . How about taking this as a project and doing some swapping ?
@@arielatom300heps It's better to run this car without an oil cooler. An oil cooler adds extra lines for the oil and further reduces pressure. Only thing you can do is run a thicker oil like 5W-30 or 40 that sees less viscosity at high temps.
Misha, I strongly recommend looking into what 900brz and Drivers Paddock on UA-cam have posted about this issue. The RTV is not the main issue as a quick dirty fix at the moment is an oil overfill and syms baffle. Oil cooler is a double edged sword as it keeps oil temps from getting into a danger zone but will be another part that will prevent oil from returning to the pan/sump.
900BRZ showed syms baffle doesn't work. He's had success with a prototype larger oil pan by verus engineering that is still early in the production process.
There’s an overload of RTV everywhere in the engine from the factory, not just the oil pan. Plus, the engine doesn’t maintain oil pressure around right hand corners. It’s just a terribly designed engine, as most Subaru engines are. Toyota should be building their owns engines with the massive resources that they have
they are killing it off, because it doesnt sell. its also due to safety regulations in EU, but videos like this, are also part of the reason why sales are down.. tracking a stock fa24 without a pan,pickup,baffle combo is asking for starvation issues. its all over motoiqs page.. they explain it in detail..
@@juanticimo It sells well enough. I think around 300,000 units between the two generations. I think Subaru isn't particularly committed to the car and Toyota is looking to move sportscar dev in house, replacing this with a new Celica with a new 2.0T.
I had a deposit down for a new GR86 when they came out but ended up getting a S2000 ap1 instead. Best decision I ever made but it’s not a daily for me so decision was easier!
For it to work properly, you need to use the block to pin the sleeve or completely close the cylinder sleeve. There are companies in Poland that handle this.
Seems like the common issue with sealant. Thank you for rebuilding the engine in such a high spec guys👏🏻 big respect for that. Can’t wait to pick it up!🥰
RTV is not the issue. right hand turns are. just get an accusump, it is around 400 euro and it delivers oil to the engine when it drop oil pressure, it is easy to install and it would prevent 90% of engine failure on the FA24.
Damn, and this engine is never bin taken apart? That amount of silicone is just terrible! I can imagine the sludge/jelly was going true the oil channels, and when engine was cooling down it blocks the flow. And when you drove it a few miles the bearings give up. Great of you guys building the car again, more reliable as ever. The new owner will have the most fun! And jokes aside, first thing in my head was siliconector joke!
Definitely a known issue. Is Subaru still pretending it isn’t or have they finally acknowledged the issue? At least as far back as 2021 (Model Year 2022) I’ve been hearing about the pickup blockages.
It's mostly internet hysteria to be honest, based on a misunderstanding of the oil pickup design. The issue the engines actually seem to have is potential for oil starvation on right hand turns under some circumstances, especially with extremely high grip tires. The "goop" in this video is not RTV. RTV does not melt under anything even resembling normal engine operating conditions.
I watched this video that had guys looked at the oil pressure of the engine during a track day, and throughout the testing session, there was a dramatic loss of pressure within the first lap and continued to stay low. Car was stock on stock tires, only thing was changed was i think the brake fluid. ua-cam.com/video/4CidHbClNHY/v-deo.htmlsi=a9Zp5Gsjybxfk0qU
I am done with the FRS, BRZ, 86 line up. There has never been a good experice for me owning a last gen and even now a new gen with the ove rusage of RTV. I hope Subaru and Toyota learn from this because in my mind it is damaging my experince with both companies and I know of others that feel the same way.
So ... did it fail because exczessive silicone blocked the oil passages and caused the bearing failure... or is it bearing failure because ... subaru ? :D
Porsche has had TONS of its own issues with their boxer engines as well. Boxer engines are wonderful for low CG but a much more complex motor to build due to the layout. Subaru does a fine job for their non-performance oriented motors but when stressed in performance applications, Subaru seems to run out of talent.
You know some other cheap sports cars at the same price of the GR86 *not* known for engine failures? Mazda Miata MX-5, VW Golf GTI, Honda Civic Si. Being cheap isn't the issue, it has a design flaw.
notorious? you mean the people that know that there is an issue on track with right hand turns, are given a way to prevent it and still choose to play the lottery? just get a fucking accusump it is not expensive or hard to install
Your on the money with that root cause, way to much silicone used in that reassembly for sure hope it go well from now all the best use Loctite Gasket Sealant very good for Subaru engines Re:
It's not even a mechanical issue, it's literally just too big of a bead of RTV. It's insane how the factory hasn't changed their SOPs and switched to a much finer nozzle tip or run an auto arm for it....
Misha what oil were you running when this happened? 0W20? 0W30? or 5W30? Also how often did you change the oil? And how many kilometres was on your GR86 when this happened? I would love to hear a response from you... Thanks!
known fault that the gaskets on the head were too thickly applied with silicon - breaks off in the engine - drops to sump - blocks sump pick up starves engine and boom... Toyota i thought had a recall for this ?
I always took my GT86 then BRZ to main dealer and this is the very reason my Gr86 will be going to the dealer for servicing to keep the 10 year warranty
Common issue ppl are having that the oil pick up are blocked up with silicone even after only a few thousand kms from new. Clearly can be seen from factory they use way too much rtv
K swap it if possible. Lmao jk, but seriously, build a K series track weapon for yourself when you have the time. You always have a huge smile every time you whip one on the ring. A happy Misha is the best version of Misha.
Always been problem with cars that had good chassies and not the power to match it.. Cars just got driven like their stolen by everyone, everywhere, get a v8 instead 😂
Excessive oil being trapped in cylinder heads is not an exclusive boxer engine problem, it has been encountered and fixed before. Anything from opening out the oil drain passages to fitting an oil return pump in the head which can be controlled by the ECU eg to turn the pump on above a certain RPM. Of course a dry sump system is the ultimate.
Subaru engines are certainly not the best representatives of the reliability of Japanese engineering
u just dont know how to take care of one.
@@bjorn3423 true every car has problem just the owner need to know before to buy a car* and ready to fight a big challenge* that all
Been doing the same engine for the last 40 years still can't figure it out Tell me you suck without telling me you suck.😂
@@bjorn3423what? this engine has issues, its not about care.
@@bjorn3423perception is reality reality is they pop all the time😂
Common problem, you need a aftermarket oil pan and pick up. I got tired of subaru with my many sti's I've owned and moved to the new nissan z
15yrs ago you would have to get a 350Z or something and the STI was better, but now I think your in the funner and faster car. Also has nice interior too
Dry sump is the only way to go with the boxer engine for track use. That’s why Porsches last a long time even stock.
@@RadDadisRadabsolutely. Dry sump if you’re tracking.
@shawnz5272 Honest question! Why the new Z vs everything else that's out there?
Yup, I got tried of Subaru quality issues and tech's here in the US not being able to properly work on them thus causing more issues. Sold the STI and got a Hellcat.
Silicone sealer is a red herring and not the reason for failures, this video continues to spread misinformation regarding the GR86/BRZ. These FA24s are suffering from a combination of oil slosh/starvation, under-filled oil capacity from a shallow pan design, and high oil temperatures combined which is a recipe for engine failures. As long as a temperatures and oil levels are kept in close check with a proper oil pan/baffle/viscosity and cooler setup, these engines can survive reliably and that has been seen with the GR cup cars if you read closely about the engine "failures" they have had on track.
I 100% agree with this…
I have been doing lots of research and spoke to the owner at “The86shop” in QLD Australian. He has raced 86's for over ten years and is very knowledgeable on the platform.
He recommends running a Motul 8100 power 0w20 with an oil cooler and doesn’t run a oil sump baffle as production racing series doesn’t let you. He has done multiple Bathurst 6 hour races on both his and other customers 86’s plus other race meetings and has never had an engine failure which I found extremely interesting as everyone says you need to run “thicker oil” and a sump baffle.
My question is how can u race a car/motor that just came out a couple years ago for 10 years?
@@Mad_Rass.mk6gli highlighting his experience…
If you have data from multiple 6 hour races please share… thanks!
@@Mad_Rass.mk6gli the aftermarket is already figuring out non-intrusive, bolt-on ways to prevent oil starvation and high temps, they're just not available to buy yet. With time, solution will only get better and more refined.
@@arielatom300heps Worth Calling Neil Bates Motorsport. They prep and look after the 86 race series cars.
Close to 20k miles on my ND2 Cup car engine.. still running strong, thanks Mazda.
What oil are you running?
The ND's engine is so fantastic. Loves to rev and sounds great. Also, it can pull 1.4G's without blowing up
I’m at 10k on my ND2 with a supercharger, feels healthy as ever besides the bad tune lol
Aren’t the gearboxes the common issue on the ND? Or do they also suffer frequent failures? I think they would make a great track car
@@DailyisRaceCar Yes, the cup cars do not run the stock trans. Quite a few folks install an NC trans if they want reliability.
I believe that oil pan baffle does little or nothing to control oil starvation issues. I autocross my GR86 and overfill the oil 1/2 quart and change the oil often.
Already proven with data
@@RacingS2000proven not to work?
@@NightKidBrandon yes
@@NightKidBrandon yea, right hand turns just drop the oil pressure. there are work arounds, like an accusump system but it is not perfect
@@RacingS2000i’m not sure where u heard that but overfilling has been shown to reduce oil pressure drops. not a complete fix but it does help
Silicone blocked oil passages, and caused oil starvation. How could a manufacturer accept this?
That sums up Subaru for you.
turns out silicone is not the cause of 99% of the FA24 failures. the car has really bad oil pressure on right hand turns
the issue is only on consistently tracked brz and gr86 on right hand turns with high g's extended turns that cause this. On the street only no problem.
The question is why is Toyota accepting this for years,, the brand famous for reliability. Bunch of clowns even there nowdays..
@@tirgod100 the cars are still new. and the issue does not affect 90% of GR86 and BRZ owners. it has nothing to do with reliability. the engines are actually very reliable. it is just a fault that shows itself in a specific setting, lets not act like they have not had things like this before. I do think they should have made a new oil pan and pickup design, offer current owners a replacement...
5:00 wait wait… that’s a Cusco oil baffle plate, meaning the sump has been opened before and re-RTV’d prior to the engine failure?
that's crazy... that means whoever opened it up slathered even more RTV on than you would even see the factory do
@@max_coast No
You don't have to watch all of Misha's videos on this vehicle.
After its purchase, the community had warned about the risks on this engine.
Therefore, Misha and the technician had tried to eliminate as many risks as possible, by upgrading the lubrication and taking the opportunity to eliminate any unnecessary RTV "at this location"
@@max_coast This needs more upvotes. The amout of BS in comment section uder this video is ridicolous.
It is irrelevant that the oil pan was opened earlier and the RTV was removed. The RTV is all over the engine, even if the RTV from the oil pan gasket is removed, it will still show up. It is not because the oil pan was opened earlier.
yes, there is an obvious sign of who ever popped that pan, had no idea what they were doing.. its very clear what happened here. plenty of people are building fa24s without issue...
Toyota made a big mistake leaving the engineering up to Subaru.
Toyota owns subaru technically. They should have put the same effort into subaru engineering like they did the BMWYOTA Supra.
@@Lupey19 could've been the b48 engine :(
The 3 cylinder gr engine comes from subaru or toyota?
@@THESHADOW97139T.
@@THESHADOW97139 It's from TGR, Toyota's motorsport division.
This is an inherent design flaw with flat engines, isn't even subaru specific, this is exactly why porsches use dry sump ($$$). bigger displacement over gen1 means that oil is getting trapped in the timing cover causing a pressure drop on high G right hand turns, conditions you're only ever seeing on a track fortunately. the excessive RTV is beat to death at this point and as far as I know there are zero confirmed cases of engines being blown by excessive RTV. Subaru redesigned the pickup to have 5 sides, and says apparently there isn't enough RTV to clog the pickup. Even if that's totally true, the jelly seen in your pan is concerning.
the oil pressure issues have been pretty well documented by 900brz. it's momentary, but after it happens enough times the engine could go at any point, like yours. seems like you need to upgrade the oiling system if you want to reliably track these things, which is a shame with how they market them. I don't track mine so it doesn't bother me but I'll likely have the pan dropped, inspected, and replaced with the correct amount of RTV as soon as the warranty is up.
Is it possible to get a dry sump for the FAs?
@@enzSa all motor
Interesting 🤔 I have been doing lots of research and spoke to the owner at “The86shop” in QLD Australian. He has raced 86's for over ten years and is very knowledgeable on the platform.
He recommends running a Motul 8100 power 0w20 with an oil cooler and doesn’t run a oil sump baffle as production racing series doesn’t let you. He has done multiple Bathurst 6 hour races on both his and other customers 86’s plus other race meetings and has never had an engine failure which I found extremely interesting as everyone says you need to run “thicker oil” and a sump baffle.
@@enzSawith the right parts you can install a dry sump kit on any engine but unless you really beat it on a track it will never be worth the investment. It's really expensive.
@@drogenfeld well that’s what I’m planning to do with the car and I doubt installing the dry sumps more expensive than a new engine
Its not about RTV in FA24 its about oil not going back to sump and pump has nothing to pick cuz oil stays in heads bigger sump can help ,problem for Misha here is that this happened on slow drive with no hard G corners and that is very hard to explain how engine can blow it self in this situation why engine had no oil pressure at 80kmh on strait road on drive to gas station.
its doest not break in second. It happens slowly.
@@jagymeister well he was on track so yea something might happend there but he didnt noticed and it started getting worse and worse with time
@@wildfrog5803 He had a few recorded money shifts with the car so people are speculating that could have been the cause.
Maybe sludge was pickup up hot on track, cools near the pump when parked and when it warms up again a it comes loose as a clump and clogs the pump or gallery, starves the engine.
@@EmptyJarDoto lol.. that might have done it.. over time it could have just failed. but he blames rtv? lol.
I've been a cylinder head machinist for 17 years and this a classic Subaru thing. The amount of silicon they use I ridiculous and they also have a tendency to have valve guides drop when overheated.
how hard is it to just remove the oil pan and scrape off all the sillicon? Also, would that even solve the issue?
@@MrAchilles113 no, the silicone is not the issue and this had been known for a long time now in the gen2 community. the issue is the oil pan / oil pickup design when going thru a hard right hand turn. the car loses oil pressure. you can get an accusump wich is a canister that hold pressurized oil and delivers it when the engine oil pressure drops. it is much cheaper than a new engine or a dry sump. it would probably prevent the majority of oil pressure related failures
the silicone is not the issue and this had been known for a long time now in the gen2 community. the issue is the oil pan / oil pickup design when going thru a hard right hand turn. the car loses oil pressure. you can get an accusump wich is a canister that hold pressurized oil and delivers it when the engine oil pressure drops. it is much cheaper than a new engine or a dry sump. it would probably prevent the majority of oil pressure related failures
rtv silicon is just a catalyst....it is right hand high G turns
@@tone3560 right. I'm not saying the silicon is the culprit, just confirming that they do use a copious amount of silicone. I know they suffer from oil starvation under extreme loads.
Per ChatGPT
“Silicone RTV (Room Temperature Vulcanizing) does not melt after it has fully cured. Once cured, silicone RTV can withstand high temperatures, typically ranging from 400°F to 600°F (204°C to 315°C) depending on the specific product. Instead of melting, silicone will eventually degrade or harden when exposed to temperatures beyond its rated limits, but it won’t revert to a liquid state like some other materials might.” 4:19
what happens if you through cured RTV in a blender with oil? Is it possible pieces broke off and were shredded throughout the engine until creating that paste?
I've seen that jelly/sludge cause a failure on a new built engine. They over packed the oil pump with assembly grease to help build oil pressure on first start, drove 50 miles did an oil change, drove 200 miles did an oil change drove 500 miles did an oil change every time the filter was cut open and inspected an was clean. 1000 miles in rod knock started they pulled the pan and it was exactly like that slimey grey goo in the bottom.
We have a saying in Australia.... Do your best Silicone the rest.... I guess it's made its way to Japan.....
To solve reliability problems, a bulkhead oil pan must be installed. The FA24 engine hates right turns because the oil pressure dropped drastically.
Did you even watch the video?
@@nastasiaj
I do and I agree with him.
We knew the problem well before this engine broke.
Look at the comments, many will tell you the same thing 😉
right, i dont get how these youtube channels keep pushing this nonsense... its totally click bait because they didnt do their due diligence, and then blame subaru.
@@nastasiaj yes, RTV is not the issue. the car drops oil pressure on hard right hand turns. if people just got some type of accusump it would prevent 90% of engine failure instead of playing the lottery-
They still haven't solved the oil starvation issues...smh. I've always wanted a brz/gr-86 for the platform but this a big turn off. I would have much preferred a version of the M20a or A25 toyota engine. Inline is generally just proven and reliable.
Those two engines are Atkinson cycle engines specifically designed for efficiency and emissions only and are meant to be ideally paired with hybrid systems. In non-hybrid cars with those two engines, they are completely gutless. As for the starvation, the aftermarket will find solutions with time and research and as soon as people stop thinking silicone sealer is a problem.
@@saad8029sealant is part of the problem. If you ignore it now it will cost you an engine sometime in the future.
@@antoinedoinell its a shame as the issue has been known since 1990's.... subaru have done nothing to stop it. They should have at least made the performance cars woth baffled sumps !
@@saad8029I know. I said a version of those specific engines. It’s Toyota. History has proven they can build inline 4’s.
You can run a 500ml overfill with 5-30 or 5-40 with oil cooler and avoid most of these problems. Have a look at the testing 900brz is doing.
Проблема не в RTV, а в том, что при правых поворотах с большим G, масло накапливается в левой голове и не попадает в поддон.
FA24 and make sure you overfill the oil by almost a quart.
That’s sketchy. Engines in normal use shouldn’t be overfilled.
@@TML34it's really not overfill. The max line is conservative, it's 1 quart less than real max. 500-750 ml over max line is totally fine.
@@TML34 testing has been done that there arent really any downsides for the fa24 and it REALLY helps oil pressure loss which is the main killer of these engines.
@@TML34 you are worried about foaming, and that doesnt happen till prob double the required amount of oil in the pan. a quart over, hell even 2 quarts over is totally fine.
ua-cam.com/video/VaTbfvzNbxQ/v-deo.html
@@juanticimo always worried about that, sometimes just depends on how the oil pan is designed.
Vulcan (a french youtuber) has broke his GR86 the same way. After a recall, the manufacturer put too much join and end it ends up the same way
RTV is not the issue... it is right hand turns. and there is an easy fix too, people just like playing the lottery instead of spending a few hundred bucks on an accusump
We run 2 stock GR86's at the NurburgRing during tourist weekends. They are also used as daily drivers. No issues yet, but we don't drive as fast, or do as many laps as Misha. I was waiting to see what the failure was as we are considering changing cars next year. Its disappointing to have to worry about possible engine failure.
Install a partitioned crankcase, with suitable oil
@@THESHADOW97139 Misha's 86 had a Cusco baffle plate and it still failed. Would be interested to know what oil he used and how often they changed it.
@@saitabit baffle plate is not a big partitioned crankcase (what it should have had, but not yet in production) 😉.
🤔I don't remember the grade of the oil, but he was switching to a slightly higher grade, to try not to have this problem... he talked about it on his videos
you need a pan, pickup and baffle, and also run about an extra quart, or more to keep the pressure up. otherwise flat engines do flat engine things..
I highly recomend looking into an accusump system, it delivers oil when whe oil pressure drops to save the engine from failure. the cars lose oil pressure on right hand turns. it is not that expensive either.
i wouldn''t rebuild a block after a bearing failure. Bearing debris is more difficult to clean out the oil passages fully.
Seems that 2nd gen GR86/BRZ are more susceptible to oil starvation issues in general. And not just due clodgs of excess sealant. FA24 more pleasant engine for daily drive, but for track use with high long side-Gs, old FA20 seems more resilant
All subaru engines are subject to oil starvation... there is so many videos on how to fix these issues.. the best being on MOTOIQ... people just refuse to educate them selves and think they can fix anything.. Subaru engines are finicky, but when done correctly can be very very reliable, even at high HP.. The FA24 in the wrx holds upwards of 500hp on stock components, with just bolt ons and e85.. the issues are the same that have always plagued these engines, track use without proper setup.. a pick up/baffle etc have to be used.. the cases puke oil, and its well documented..
@@juanticimoits no excuse though, Subaru have known about these issues for 30+ years and not fixed them. IMO there is no way to fix these issues without an Accusump or Drysump. Baffles do not work in the EJ, the oil capacity is just wayyyy too low. The EJ needs like a 8 litre sump, not 4.4. 4.4 litres is enough for a 1.4 or 1.3 engine , not a 2.0 turbo.
all you need is an accusump. people jsut dont want to spend the 400 something bucks to get one. what a shame that such a simple thing could save 90% of the engine failure on gen2 cars
@@turbo________ I think the point is you shouldnt have to buy an accusump. And Subarus S**t engineering should have been fixed 30 years ago .
@@bigkaswrx8115 obviously. but shit happens and every engine nad every car has flaws. the oil pan is just bad. unless someone makes a completely new oil pan that eliminates the oil completely sloshing out of the oil pan and away from the pickup, an accusump will be you best option. just get the biggest one you can I guess :D
I had a '99 2.5 Legacy back in the day. Great car, loved the handling etc. One day, as I was pulling up to the house, the engine just stopped dead and wouldn't turn over. Crank seized. :(
Hopefully there is a kit with your stroker kit that has a better baffling system for the oil starvation problem during the right hand turns.
Ah, yes. The good ol' Subaru banana crank.
Lol 😀
Boggles my mind why they wouldn't just use a gasket like everyone else. It seems like it would also be quicker to assemble as well.
it is asembled by machines. so RTV is simpler. still RTV is not the issue and this has been known for a while now. it is hard right hand turns on track. there is a simple fix too, just get a fucking accusump instead of playing the lottery
Wait until you guys find out the pistons on the HKS pistons are the exact bore as OEM so you can’t bore out the cylinder walls in the event of damages, you have to use oem new cylinder walls or pray yours don’t have damage. This is straight from HKS for their specs and IAG as far as potential machining issues lol
I still don't understand why you didn't upgrade at first place engine if you are know you will be tracking that car, as minimum upgrade oil pan with baffled sump and oil pick up which would prevent that issue for time being
I believe it's because he did not expect that, or conspiracy theory he did that for the content haha. Also apparently he tried to seal it better than subaru did
@@alphaenterprise2232 I wouldn't expect that too, but I assume he built it as track car? If yes then I would build at least forged engine for track car with 11mm or 14mm headstuds just in case
Baffled sump and oil pick up is literally minimum upgrade for that car, if he does more drifting or he exceeds that then dry sump it to be on safe side, over here in UK people run on their EJ207 or EJ257 baffled sump with uprated oil pick up and they do a lot of sprint series and track days without any issues, dry sump is if you are loaded
Hopefully won't end up as Donut media and their Subaru High and low car builds🤦
misha, those engine have oil starvation issues under high G's. unless you address that, it going to blow up again. good luck !
I have no idea why people track the cars knowing there is an issue, and that there is a clear and simple way to fix it. get a fucking accusump. fuck the oil baffles, fuck scraping off the RTV just get an accusump. cheap and easy to install too
@@turbo________ a few people have data logged a bunch of runs on the track and even with accusump on long right turns, the engine oil pressure drops... and thats with bigger pan and baffles too. I wonder how porsche does it at this point lol
@@NimaSomeh yea I have seen that. still it is the best you can do right now. A bigger canister would help or maybe a dual canister setup so the 2 individually smaller canisters fit under the hood. porsche uses some kind of a dry sump system from what I know
This is one of the more informative RTV issues videos, damn makes me rethink how long I wanna keep the car
These cars loose a lot of oil pressure during sustained and harsh right handed turns. From what I’ve seen from people who race them, an oil sump, the right oil (a 40 weight oil for racing), a baffled oil pan, and adding an extra .5 qt of oil will reduce the amount of pressure loss significantly.
Also removing the heater core helps with reducing the oil pressure loss in these engines
why i got a built engine in my subaru was because my engine blew up leaving a gas station parking lot at 15 mph. lol no high revving or launching honestly i shouldnt have gotten an IAG engine and rebuilt it but i did. the same issue is inevitably going to happen again.
Problem is, the quality of gaskets and sealing rings is going downhill at the moment, even for OEM parts.
So they are sort of promoting siliconing up things to cover for the crappy gasket's you are getting.
And as another UA-camr said, this is what will kill the internal combustion engine... Crappy unreliable parts, even when you pay good money for it.
Holy shit! The RTV issue isn't just specific to the oil pan, it extends to the entire engine assembly? That's it, my last 3 new vehicles were Subaru's.. next one won't be.
Knock, knock. - Who's there? - The Subaru engine.
Does that have any bearing? (I own a few)
Any updates on the build? Really interested to see how much it makes with the stroker kit!
Will be interesting to see how much power the car makes on the dyno once the stroker kit is installed.
make sure to inspect every oil galley before reassembly
Stroker kits aren't really about peak power but more torque... so although number gains won't be much you could make 100hp like 2000rpm lower maybe but peak power lower
it is mostly about having to replace the internals so why not go with the stronger HKS goodies
@turbo________ I totally agree... if something breaks, perfect time to upgrade
My first gen engine also died on the street just by idling in the parking lot. Very strange stuff. So it’s something that affects both gens. Curious if they will continue the way with the gr yaris engine in the next gens as they already racing a gr86 on altenative fuel with that engine.
There is a reason why inline four is used by everybody. Like that meme: just because you are different does not mean u are useful
A larger capacity oil pan with revised baffles should be installed on the new motor...and the new owner should run a heavier weight oil
I sold my GR86 after discovering the RTV issues almost 2 years ago. Never regretted that wise decision.
Seems like most folks are overfilling by .5 or 1 qt and are fine.. Granted they're not on the Ring, but just 'regular' tracks.. If you're really concerned.. should've gotten an Accusump.. maintains pressure in the oil system no matter what.. $800 USD
Owner is getting a jewel, built engine with a hks stroker!
Normal amount of sealant from factory not the cause of failure... maybe oil starvation due to oil surge on track running
Check the oil pump in the front cover....
How are the cams and cam caps
lol, how many kms was on it for the bearings to look like that? Fookin hell
That bearing is impressively fucked. I don't even know how much worse it could get before it exploded.
I know now that i probably dodged a bullet not buying a GR86...
What you got instead?
@@Carlos.Rivera an mk8 Golf GTI, not exactly what I was looking for, but I don't regret it one bit!
No real problems on the road at the moment, only on the track and especially with very sticky tires 😉
Are you tracking the car on 200tw tires? If not, the car would have been fine.
@@Chris-hw4mq true.. rtv was not the issue. he's just blaming it on his shitty treatment of the car.
Here it would be worth thinking about building a new car . This engine is...The problems were mentioned several times in the chat . I would really try maybe a different car / engine . How about taking this as a project and doing some swapping ?
V8 GR86 would be awesome.
Is this a video from a long time ago ? Or is it only now being rebuild?
Wouldn't a oil analysis showed the amount of silicone in the oil?
Good idea !.
Oil analysts would have been good insurance since the car was being tracked hard without a oil cooler…
So it all boils down to user error, case closed
This should be an old video for all I know
@@arielatom300heps It's better to run this car without an oil cooler. An oil cooler adds extra lines for the oil and further reduces pressure. Only thing you can do is run a thicker oil like 5W-30 or 40 that sees less viscosity at high temps.
cant wait for the update to see how this thing sounds and drives with the stroker kit!!
Amazes me how easily Subaru engines fall apart. As someone that had a Ver. 5 STi engine....
Misha, I strongly recommend looking into what 900brz and Drivers Paddock on UA-cam have posted about this issue. The RTV is not the main issue as a quick dirty fix at the moment is an oil overfill and syms baffle. Oil cooler is a double edged sword as it keeps oil temps from getting into a danger zone but will be another part that will prevent oil from returning to the pan/sump.
900BRZ showed syms baffle doesn't work. He's had success with a prototype larger oil pan by verus engineering that is still early in the production process.
Hrm. Oil starvation, leading to a spun bearing... On a Subaru... why am I NOT surprised!?
judging by the Cusco plate in the pan, someone opened the engine and overused the sealant during assembly. Subaru has nothing to do with this.
There’s an overload of RTV everywhere in the engine from the factory, not just the oil pan. Plus, the engine doesn’t maintain oil pressure around right hand corners. It’s just a terribly designed engine, as most Subaru engines are. Toyota should be building their owns engines with the massive resources that they have
Probably why toyota is ending their joint venture and i believe they will put the 1.6 turbo from the gr yaris now. Or the newly developed 2 liter
they are killing it off, because it doesnt sell. its also due to safety regulations in EU, but videos like this, are also part of the reason why sales are down.. tracking a stock fa24 without a pan,pickup,baffle combo is asking for starvation issues. its all over motoiqs page.. they explain it in detail..
@@juanticimo It sells well enough. I think around 300,000 units between the two generations. I think Subaru isn't particularly committed to the car and Toyota is looking to move sportscar dev in house, replacing this with a new Celica with a new 2.0T.
I read the 2028 GR86 is supposed to use the three cylinder 300hp engine and be a hybrid.
Its a known issue that the excess gasket material blocks the oil pickup
This is not the problem here
Gr86 common issue... terrible oil handling... you need a dry sump and custom oil pan
I had a deposit down for a new GR86 when they came out but ended up getting a S2000 ap1 instead. Best decision I ever made but it’s not a daily for me so decision was easier!
For it to work properly, you need to use the block to pin the sleeve or completely close the cylinder sleeve. There are companies in Poland that handle this.
Pin the sleeve?? You mean to block certain oil passages?
tf are you talking about
Is it silicon instead of solid gasket? Can you make custom gaskets then? Or is it the O ring type gasket i dunno lol. Goodluck Misha
It’s fine to use RTV-type sealant but you have to be precise with the amount applied.
This is a boxer engine! The problem is not the gasket! It’s a problem between the two blocks and the crankshaft
most engines use RTV and its perfectly fine. Problem is amount of it.
RTV is not the issue, right hand turns are. just get an accusump and it would fix 90% of engine failures on the FA24
Why can't subaru just use gasket instead of RTV? They would always end up on oil pick up and block it. This has been an issue for a long time already.
RTV is not the issue. right hand turns on track are. just get an accusump and it would fix it and prevent engine failure on 90% of FA24s
@@turbo________ it is. Did you watch the video? Check atleast at 4:10 and see the excess rtvs on the oil sump.
@@butcht6309 can you read? I didnt say that there is no excess RTV. I said that the RTV is not the issue.
Seems like the common issue with sealant.
Thank you for rebuilding the engine in such a high spec guys👏🏻 big respect for that.
Can’t wait to pick it up!🥰
So you are the lucky one
RTV is not the issue. right hand turns are. just get an accusump, it is around 400 euro and it delivers oil to the engine when it drop oil pressure, it is easy to install and it would prevent 90% of engine failure on the FA24.
this is partially why i got the mx5RF a bit more robust even though the center of gravity is slightly higher
Even in Japan, these GT/GR 86 engines are notorious for being unreliable if you did something to it.
lesson: never let an engine warm up by allowing it to idle
Damn, and this engine is never bin taken apart? That amount of silicone is just terrible! I can imagine the sludge/jelly was going true the oil channels, and when engine was cooling down it blocks the flow. And when you drove it a few miles the bearings give up.
Great of you guys building the car again, more reliable as ever. The new owner will have the most fun!
And jokes aside, first thing in my head was siliconector joke!
As far as i know this is a known problem , also with the subaru model
No really, the same engine has the same problems?
@@Boykot1 idk if its the same engine , just shared my info bud... tried to ne helpfull👍
Definitely a known issue. Is Subaru still pretending it isn’t or have they finally acknowledged the issue? At least as far back as 2021 (Model Year 2022) I’ve been hearing about the pickup blockages.
It's mostly internet hysteria to be honest, based on a misunderstanding of the oil pickup design. The issue the engines actually seem to have is potential for oil starvation on right hand turns under some circumstances, especially with extremely high grip tires. The "goop" in this video is not RTV. RTV does not melt under anything even resembling normal engine operating conditions.
@@Charles-ee5mm as far as i know they put too much rtv on stuff and that gets lose and blocks the pickup *correct me if im wrong
I watched this video that had guys looked at the oil pressure of the engine during a track day, and throughout the testing session, there was a dramatic loss of pressure within the first lap and continued to stay low. Car was stock on stock tires, only thing was changed was i think the brake fluid.
ua-cam.com/video/4CidHbClNHY/v-deo.htmlsi=a9Zp5Gsjybxfk0qU
I am done with the FRS, BRZ, 86 line up. There has never been a good experice for me owning a last gen and even now a new gen with the ove rusage of RTV. I hope Subaru and Toyota learn from this because in my mind it is damaging my experince with both companies and I know of others that feel the same way.
Misha estos videos tambien nos gustan mucho.
Deseando ver terminada la reparacion del motor.
So ... did it fail because exczessive silicone blocked the oil passages and caused the bearing failure... or is it bearing failure because ... subaru ? :D
Subaru and not getting oil, name a more iconic duo
There is a research on that engine
It looses oil pressure on high speed turns.
After owning a Subaru, I can say I wont be going back. The amount of money you need to put into them just to have fun at the track is upsetting.
The excess RTV issue is why I didn't get a GR86 and got an 11th gen si instead.
Honda's 1.5T has had plenty of it's own issues!
@@bearclaw5115 I'm aware
Only Porsche knows how to make flat engines.
😂😂😂
french too 👀
Well, yes, they just boOost them a little less...
you mean by using a dry sump?
Porsche has had TONS of its own issues with their boxer engines as well. Boxer engines are wonderful for low CG but a much more complex motor to build due to the layout. Subaru does a fine job for their non-performance oriented motors but when stressed in performance applications, Subaru seems to run out of talent.
Stock oil pump always was a garbage that turns oil into a foam. That's the reason
It's a cheap sportscar notorious for engine failures.
You know some other cheap sports cars at the same price of the GR86 *not* known for engine failures? Mazda Miata MX-5, VW Golf GTI, Honda Civic Si. Being cheap isn't the issue, it has a design flaw.
notorious? you mean the people that know that there is an issue on track with right hand turns, are given a way to prevent it and still choose to play the lottery? just get a fucking accusump it is not expensive or hard to install
@@turbo________ its no use people love to jump to conclusions with these things.
You guys need to understand 1 thing, its not track car with track engine. Its a car on normal roads
Silicon is bad in women and silicon is bad in car engines as well!
Your on the money with that root cause, way to much silicone used in that reassembly for sure hope it go well from now all the best use Loctite Gasket Sealant very good for Subaru engines Re:
It's not even a mechanical issue, it's literally just too big of a bead of RTV. It's insane how the factory hasn't changed their SOPs and switched to a much finer nozzle tip or run an auto arm for it....
It has a Cusco baffle, so someone outside the factory has already opened it and slazzed the shid out of it.
Misha what oil were you running when this happened? 0W20? 0W30? or 5W30? Also how often did you change the oil? And how many kilometres was on your GR86 when this happened? I would love to hear a response from you... Thanks!
Ooook, you need to check the oil pump clearlance now!
I have a suspicion they might put in a new oil pump. With that much metal paste in the oil, you can almost guarantee that the oil pump has had it.
No problem here
known fault that the gaskets on the head were too thickly applied with silicon - breaks off in the engine - drops to sump - blocks sump pick up starves engine and boom... Toyota i thought had a recall for this ?
I always took my GT86 then BRZ to main dealer and this is the very reason my Gr86 will be going to the dealer for servicing to keep the 10 year warranty
But the Oilpan was off to mount the Cusco Baffel in the Sump right?! and there was a bit too much Silicone on the Pan also i believe?! 👀
But... Subaru/ Toyota didn't test this car in Nurburgring before to sell them ?....
Old news. Why not just drop pan, inspect for excess silicon before tracking car initially?
Misha i didn't watch the entire video but pistons and rods wont solve your problem. Get an aftermarket oil pan and pick up bro
this 100 times over... pistons and rods dont cause oil starvation lol
or just get an accusump
@@juanticimo yea but if you are replacing it why not go with the HKS goodies. either way he should have gotten an accusump on DAY 1
Need to install an oil pressure accumulator.
Drop everything you're doing when Misha uploads!
Common issue ppl are having that the oil pick up are blocked up with silicone even after only a few thousand kms from new. Clearly can be seen from factory they use way too much rtv
These engines warranties should be extended to higher than 60k from Toyota and Subaru!
K swap it if possible. Lmao jk, but seriously, build a K series track weapon for yourself when you have the time. You always have a huge smile every time you whip one on the ring. A happy Misha is the best version of Misha.
I've never ever heard of a bullet proof boxer engine
Porsche…
Why not ?.
@@peterlund9323 996 models and IMS problems, for example?....
@@MDEV-86x86 996/997 and .... more again .
But it`s not the same price😉
Always been problem with cars that had good chassies and not the power to match it.. Cars just got driven like their stolen by everyone, everywhere, get a v8 instead 😂
Excessive oil being trapped in cylinder heads is not an exclusive boxer engine problem, it has been encountered and fixed before. Anything from opening out the oil drain passages to fitting an oil return pump in the head which can be controlled by the ECU eg to turn the pump on above a certain RPM. Of course a dry sump system is the ultimate.