@BoosterUM they're either a troll or a bot, either way ignore them. If they're for sure a bot (identical posts in every comment thread) report it as spam.
that should have been part of the video. given how easily lpl found the right set on each pin, I'm inclined to believe that raking still has a reasonably good chance of working. though it should take several times longer than with all standard pins.
@@Ass_of_AmalekWell, keep in mind he also knows this lock really well. If the only thing they replaced were the pins, he could probably rake it a lot easier than someone less familiar could. Like how replacing just the cushions on your couch won't have much effect on your ability to navigate the living room.
Anyone watching this video is probably capable of re-pinning the lock with whatever pins seem best. How is the quality of the lock otherwise? Can it be made good?
LPL had more problems getting the assembly screw out than picking the lock. A miracle just happened, LPL actually praised ML, if only slightly. The world is officially coming to an end.
The expression you are looking for is "damned with faint praise". Someone a bit earlier said Masterlock is going "back to the drawing board" on this - naah. Masterlock have their products and they are making a very nice -product- profit, thank you. Why spend money on R&D? Don't be silly.
It couldn't be raked (or at least didn't appear to be from this video) and LPL said it was an improvement. That is one of the best reviews of a masterlock I've seen on this channel.
“For that, I do commend Master Lock.” In other news, Demon News reports that the weather in Hades is below freezing and the whole place has frozen over.
@@weswheel4834 IIRC he said he prepares in advance, to make the videos shorter, so unless he says so, I assume he has already picked the lock before (and it is easier the second time). There are a few videos where he opens the package on camera, he is still really fast when going blind, but maybe not as perfect as this.
@@gubx42 Yeah, I wasn't criticising him. But obviously if he's just picked it off-camera then it isn't really fair to compare his time (as I did) to the time that someone may take to pick it in the wild :)
LPL: "Don't expect this to last more than 30 seconds or maybe a minute when being picked." LPLs actual pick time was 11seconds, but I guess getting the tools out and into position, and explaining it while filming took 38 seconds total. So he was correct: 30 seconds to a minute. Someone could make a video of picking your lock, taking your valuables, and disappearing all in under a minute.
Nice to see a pick and gut video again. Used to love watching those back in the day. That sound of the pins sliding when the core was being pulled was always something I looked forward to.
Master lock makes their units more difficult to dissemble instead of increasing the difficulty of its pick resistance. Put the core on the inside of the shackle and the hex screw in the key hole. Perps would at least be confused at first. And then have to go into their tool box for an L key. Increasing the time significantly
I have actually seen someone use structural screws to seal a door shut. Sure, the key is technically common but it's going to be really loud to open or extremely time consuming if they want to unscrew it by hand.
@@Yukimaru0 could also just bring out the welder and just weld it shut, that way nothing less than an angle grinder will allow people to go through, sure to be woken up at night
Yesterday someone had trouble with a Master lock combination lock where I was. Even with the correct combination it wasn't opening. I tried myself but couldn't get it, then I remembered your videos where locks had been struck with a mallet and opened that way and asked if there was something solid we could use. A person had a Swiss Army tool and managed to use it to pry the lock open, not quite the same result but none the less a problem avoided thanks to your teachings LPL.
it'd actually be a little more difficult if it had 3 or 4 spools, because you have to be careful when pulling the spools out of a false set to not drop pins that are fully set. Still a nice improvement from masterlock though, and likely wouldn't be able to be raked open with most bittings, which is likely all this needs to protect against in reality.
So instead of making it meaningfully harder to pick, they just made it slightly harder to take apart to show why it's so easy to pick. Bravo, Masterlock.
I find it so interesting how easy a master picker can open what should be a strong average lock. It must be sad and boring for LPL to not have a serious challenge to go through from time to time. Thank you for sharing the video that you create.
I just bought this the other day and had a lot of trouble picking it (I'm a bit of a noob) I watched a few videos of the older revision and it looked so much easier, and they didn't have spools! I thought I was really bad if I had trouble getting standard pins open. Glad to know it was spools! I've picked it once but this will be a good lock to improve my skills
Seeing the speed he pick and disassemble a lock, I think LPL would be the style of thief that leaves a key impression of the key and a note on why the lock wasn't secure after a break-in just to taunt even more the victim.
Chopsticks are ez to use for someone with good dexterity with their hands such as a puzzle enthusiast or a competitive or professional lockpicker I wouldn't doubt it.
Dang man you took it completely apart faster than most people could pick it. Not to mention you picked it faster than I could have raked it with all standard pins lol
So a terrible lock is a little less terrible now…got it! The fact that it took more time for LPL to OCD the pin orientation on the plate than it took him to pick the lock says it all.
At least it actually required single pin picking and not the good ole wave rake! I'm still a bit surprised the spools didn't slow him down a tiny bit more.
I think for Halloween, some kids should dress up as a pair of hands, bearing the letters "LPL" and holding a tensioner and hook, and then "trick-or-treat" all the Masterlock directors! The LPL just has to be the bogeyman for Masterlock!
The tools made by Covert Instruments seem to be really well made. I'm not really into picking, but if I were I'd probably buy'em, also I love your content, great stuff!
![[1550] Better Than Expected: Toledo 40mm Alum. Padlock](http://i.ytimg.com/vi/2GJpGl4CsAI/mqdefault.jpg)
![[1550] Better Than Expected: Toledo 40mm Alum. Padlock](/img/tr.png)
![[1543] Legal Department Keyway Design?](http://i.ytimg.com/vi/NMfpJ6EzqFI/mqdefault.jpg)
About 2 seconds per pin. That’s remarkable for a Master Lock.
I told my infant to blink if they’re trans. They blinked. My infant came out as trans.
@@TransKidsMafia Sounds like they’re more secure than a Master Lock.
I wanted to see him try to rake it anyways
@dli7423 tf are you talking about. Is bait the only thing that gets you off?
@BoosterUM they're either a troll or a bot, either way ignore them. If they're for sure a bot (identical posts in every comment thread) report it as spam.
Well as long as it cannot be easily raked, its a huge improvement.
that should have been part of the video. given how easily lpl found the right set on each pin, I'm inclined to believe that raking still has a reasonably good chance of working. though it should take several times longer than with all standard pins.
@@Ass_of_AmalekWell, keep in mind he also knows this lock really well. If the only thing they replaced were the pins, he could probably rake it a lot easier than someone less familiar could. Like how replacing just the cushions on your couch won't have much effect on your ability to navigate the living room.
I'm sure McNally will find a way to open it with his signature ramming method
@@DeathsWeepingAngel methode anlauf statt gleitgel, as we say in germany
Anyone watching this video is probably capable of re-pinning the lock with whatever pins seem best. How is the quality of the lock otherwise? Can it be made good?
LPL had more problems getting the assembly screw out than picking the lock. A miracle just happened, LPL actually praised ML, if only slightly. The world is officially coming to an end.
The expression you are looking for is "damned with faint praise".
Someone a bit earlier said Masterlock is going "back to the drawing board" on this - naah. Masterlock have their products and they are making a very nice -product- profit, thank you. Why spend money on R&D? Don't be silly.
Ya I think that's an end times proficiency
peace in Israel and the lock picking lawyer makeing peace with Master lock.
His words where faint praise but his skills were still scoffing ML
He had more trouble putting the pins on the tray. 😂
If "congratulations for doing the bare minimum" was a compliment 🤣
Oh boy! A Master Lock video? And its longer than 3 minutes? Its a miracle!
my toddler came out as trans. They’re living their truth
No miracle - it took much, much longer to disassemble the lock than to pick it …
Only because LPL takes apart the lock.
Twenty seconds to pick, the rest is additional material.
Get jebaited 😅🤣
See's it's a 5 minute video featuring a Masterlock: Ooooh...oh wait he's just taking it apart
It couldn't be raked (or at least didn't appear to be from this video) and LPL said it was an improvement. That is one of the best reviews of a masterlock I've seen on this channel.
“For that, I do commend Master Lock.” In other news, Demon News reports that the weather in Hades is below freezing and the whole place has frozen over.
In the spirit of The Tim Traveller: In Dante's _Inferno_ one of the circles in fact _has_ frozen over.
Is that part of Donut News Network?
And their ceo just committed friendly Gand rape of his engineers…
Plus, pigs were flying all over the place.
@@williamromine5715I've seen it on a Pink Floyd album.
From touching the first pin with your pick, that took you about 10 seconds, with spool pins. You truly are a master of your craft.
I liked where he converted that time to a time for someone who "knows what they're doing" (30 seconds to a minute).
He only needed one pass thru the pins as well, so little lucky?
@@ArmadilloGodzilla I wonder if it was because he’d picked it prior to the recording, and knew that they were spools.
@@weswheel4834 IIRC he said he prepares in advance, to make the videos shorter, so unless he says so, I assume he has already picked the lock before (and it is easier the second time). There are a few videos where he opens the package on camera, he is still really fast when going blind, but maybe not as perfect as this.
@@gubx42 Yeah, I wasn't criticising him. But obviously if he's just picked it off-camera then it isn't really fair to compare his time (as I did) to the time that someone may take to pick it in the wild :)
LPL: "Don't expect this to last more than 30 seconds or maybe a minute when being picked."
LPLs actual pick time was 11seconds, but I guess getting the tools out and into position, and explaining it while filming took 38 seconds total.
So he was correct: 30 seconds to a minute.
Someone could make a video of picking your lock, taking your valuables, and disappearing all in under a minute.
A Master Lock Video, this will be quick
@@TransKidsMafiathen you have failed them. Weirdo!
Ho ho.
Yes mrs LPL 's beaver needs raking out of some dust with the big 8 inch rake pick. 😎🤣😜 So a quik and easy master junk video and back to the beaver...
MasterLock: You don't seem him slipping a shim into the shackle, do you? These are new and improved!
Nice to see a pick and gut video again. Used to love watching those back in the day. That sound of the pins sliding when the core was being pulled was always something I looked forward to.
Master lock makes their units more difficult to dissemble instead of increasing the difficulty of its pick resistance. Put the core on the inside of the shackle and the hex screw in the key hole. Perps would at least be confused at first. And then have to go into their tool box for an L key. Increasing the time significantly
Which makes sense, if you are trying to quietly get a lock open it makes sense to just take it apart if the low skill attacks dont work
I have actually seen someone use structural screws to seal a door shut. Sure, the key is technically common but it's going to be really loud to open or extremely time consuming if they want to unscrew it by hand.
@@Yukimaru0 could also just bring out the welder and just weld it shut, that way nothing less than an angle grinder will allow people to go through, sure to be woken up at night
@@celivalg Why stop there? Encase the whole thing in concrete after you weld it. A jackhammer is gonna be even louder than an angle grinder.
@@Just_A_Dudewhy stop there? Send the whole thing into space. That way if it gets broken into, you know you can just blame Elon Musk
It took longer to unscrew the hex screw than it took to pick the lock!
"I do commend Master Lock" Truly a sign of the apocalypse.
masterlock: We finally got him!
LockPickingLawyer: picks it almost as fast as using a key.
masterlock: ...back to the drawing board, boys!
more like
"technically, we did try. good enough, I say!"
LPL: I do commend MasterLock
MasterLock: we are now recommended by LPL!
new achievement: no wave rake by LPL
Master lock is security by obscurity... ( sorry lpl i stole that one from you )
Lol master lock just wants $ everything else is a lie.
Finally a video featuring picking and gutting. I missed these. That's the single reason why I sub this channel. Keep it up.
The pin at 3:49 put up more of a struggle in the tray then it ever did in the lock.
*than
I'm a simple man. I see a teardown of a lock, and I hit that like button.
The new pin tray looks great! I can't wait to see McNally use it as a throwing blade to explode a Dr. Pepper or something.
No, it'll be thrown into the void when he opens a lock and sees the disappointment
Nah he will gently tap the lock with it to open it then launch it through a watermellon
The sound of the tweezers scraping was like nails on a chalkboard to me unfortunately.
LPL: "Definitely an improvement ..."
Masterlock: "Mass produce them! NOW!"
Good joke, but Master Lock doesn’t make anything not mass produced. Maybe double the production rate instead?
Very nice demonstration.
I was actually picking a 930 at work the other day and was surprised when I felt a spool. I had to double check that it WAS a Master lock lol.
What's even more amazing is LPL puts them back together in working order.
I mean with the Master Locks, he might as well just huck em in the bin 😅.
Old school lock pick and gut! Miss seeing these.
I see a video over 2 minutes, i am astounded by the lock and instantly intrigued.
The fact it took you three times as long to get the hex screw out compared to picking it is hilarious
Took him longer to get the pick and turner out of the covert companion
I love spool pins. They tell you exactly what they are, and exactly what's going on with them.
Awesome to see another disassembly!
Yesterday someone had trouble with a Master lock combination lock where I was. Even with the correct combination it wasn't opening. I tried myself but couldn't get it, then I remembered your videos where locks had been struck with a mallet and opened that way and asked if there was something solid we could use. A person had a Swiss Army tool and managed to use it to pry the lock open, not quite the same result but none the less a problem avoided thanks to your teachings LPL.
A Master Lock that doesn't just melt in his presence is a big improvement !
You know, Masterlock executives only heard LPL say "I do commend Masterlock".
Nice lock, great picking and tools, but then it's you !!!!!
have a great day
I love how concise your videos are. Thanks.
I don't think I've seen a gutting video since Bosnian Bill was active, much appreciated!
Lock Noob does a ton of them still
I especially enjoy the videos in which he takes the lock apart and shows us what's inside.
Permanently closed- that means master lock is more afraid of you opening the cylinder than the lock
Then why didn't they wrap it in duck tape? (-:
Master Lock should know by now that nothing is closed to LPL! 😂🤪
Well, at least it took more than a gentle raking, I suppose
I am amazed after all the years of lock makers making locks you can still pick locks this easily. Especially from master lock.
On the next MasterLock commercial and all over every website they own:
"I do commend MasterLock" - LockPickingLawyer, October 2023
Love seeing a tear down!
Good job Master lock for adding security pins that will at least make simple picking techniques like raking more challenging.
Thank you, I always learn something from your videos.
Amazing! I don't think I've ever heard charitable words for Master on this channel.
Good old Master Lock! Rave reviews from LPL!
Damn! You can't trust your dirty secrets to any lock if this guy is around
Oooo, I think, a 4:40 LPL video, maybe Masterlock has raised its game. Then, ten seconds later, "we got this open"!
"Hex screw down the shackle hole" now lives rent-free in my head.
It took longer to get ready to pick than the actual picking itself. Way to go, Masterlock.
All spools. Ahhhh master. Never stop being you. 😘
What a boss. Setting 5 spools like it's nothing. The pro series is just like this but 6 pin (if the locksmith puts in all 6)
it'd actually be a little more difficult if it had 3 or 4 spools, because you have to be careful when pulling the spools out of a false set to not drop pins that are fully set.
Still a nice improvement from masterlock though, and likely wouldn't be able to be raked open with most bittings, which is likely all this needs to protect against in reality.
22 seconds from beginning to end, a remarkable improvement for Masterlock. Thank you to all the people who emailed him about this lock. 😅
"down the shackle hole" sounds like a LPL movie title
"Obviously an improvement." Champagne corks popping over at master lock.
You have some good damn tools and you plug them just as good
Would love to see a full size Pinning Tray, similar to the ones you've used on the Covert Instruments store!
So instead of making it meaningfully harder to pick, they just made it slightly harder to take apart to show why it's so easy to pick. Bravo, Masterlock.
An effort by ML. Outstanding. Now let’s see them populate the sixth pin location.
Thanks LPL
I find it so interesting how easy a master picker can open what should be a strong average lock. It must be sad and boring for LPL to not have a serious challenge to go through from time to time. Thank you for sharing the video that you create.
Master lock... We came out with a new design, its un pickable!!
LPL... Hold my wiskey and watch this!!
This would be the closest to a “Master Lock sponsored” video by LPL I can think of.
Great video and very informative.
Nice to see a disassemble again. I've missed those.
I just bought this the other day and had a lot of trouble picking it (I'm a bit of a noob)
I watched a few videos of the older revision and it looked so much easier, and they didn't have spools! I thought I was really bad if I had trouble getting standard pins open.
Glad to know it was spools! I've picked it once but this will be a good lock to improve my skills
MasterLock: "We need security pins in our locks!!!" - "just lets make 'em all spools! Those are tricky!!" - "great Idea! And we can mass produce 'em"
Without watching the video, my first thought was: "Oh, it cannot be opened with just anything now? I'm officially intrigued!"
I love your videoes.... great job👍👍
You upload so regularly. Thank yoiu.
Masterlock: New and improved!
LPL: That's cute
"If someone knows what theyre doing, dont expect this to last more than 30 seconds or a minute." He said, after picking it in like 10 seconds.
Monumental occasion, masterlock improved something
Seeing the speed he pick and disassemble a lock, I think LPL would be the style of thief that leaves a key impression of the key and a note on why the lock wasn't secure after a break-in just to taunt even more the victim.
Master lock decides to improve their lock, does the bare minimum. One small step for master lock. That’s it, that’s all I got. One small step.
* grabs chest *
A praise for Master lock?!
Not used to that
Perhaps there is hope.
Random thought here:
Lockpicking Lawyer is probably REALLY good with chopsticks.
Just saying 😂
Great Video btw!
😂
Chopsticks are ez to use for someone with good dexterity with their hands such as a puzzle enthusiast or a competitive or professional lockpicker I wouldn't doubt it.
"I do commend MasterLock." -LPL
🍾
I liked seeing the disassembly of the lock
Dang man you took it completely apart faster than most people could pick it. Not to mention you picked it faster than I could have raked it with all standard pins lol
WOW, It took you longer to get the hex head screw out than it did for you to pick the lock. Well done!
4:13 "I do commend Master Lock."
The Master Lock marketing department just found a new quote for their ads.
Congrats on your weight loss, hope you're doing well.
It's great to see the security pi..... and it's open...
So a terrible lock is a little less terrible now…got it! The fact that it took more time for LPL to OCD the pin orientation on the plate than it took him to pick the lock says it all.
Thanks
Interesting to see what you are talking about when you say a spool pin. I enjoy your work and seeing the details helps.
I just bought one of these on 1/4/23. Picked it blind in one attempt, about 8 seconds. Gutted and found 5 standard pins.
I'm going to have to use the phrase "right down the shackle hole" in a conversation.😂
LPL- looks at the lock sternly. Lock in a sorrowful tone, "Fine." Lock opens up.
At least it actually required single pin picking and not the good ole wave rake! I'm still a bit surprised the spools didn't slow him down a tiny bit more.
Absolutely rapid! Outstanding haha!
Any lock keeps an honest man honest, thieves will defeat locks quickly.
oh good, master bought some spool pins. anyways...
I think for Halloween, some kids should dress up as a pair of hands, bearing the letters "LPL" and holding a tensioner and hook, and then "trick-or-treat" all the Masterlock directors!
The LPL just has to be the bogeyman for Masterlock!
I, too, have an improved round body.
Thanks for doing the update video. Though with Master Lock not improving tolerances the spool pins are easily defeated. Cheers
The tools made by Covert Instruments seem to be really well made. I'm not really into picking, but if I were I'd probably buy'em, also I love your content, great stuff!
Commend Master Lock... never thought I'd hear that
Master Lock actually made a lock that lasted longer than a split second before it was picked! This one takes 5 to open! Impressive!