Echo CS400 No Start Easy DIY repair and SURPRISE find
Вставка
- Опубліковано 26 кві 2022
- Ethanol killed another saw. Echo CS 400 Will it start and a surprise problem with explanation and solution repair. Come along for the diagnose and repair. Easy DIY.
Thanks for watching!
-Ray
As an Amazon Associate I earn from qualifying purchases.
Tune up kit: amzn.to/393fP6f
If you choose to try one of the suggestions made in this video, you do so at your own risk. No information contained in this video shall create any express or implied warranty or guarantee of any kind. Any injury, damage or lose that my result from the improper use of tools, equipment or information contained in the video is the sole responsibility of the viewer and not Ray of all Trades. Please ensure that you take all proper recommended safety before attempting any project. Ray of all Trades assumes not liability for property damage or injury incurred as a result of any of the information contained in the video. If you would like to send a product for me to honestly evaluate or just things you think I could use, please mail to:
Ray of all trades
PO Box 6016
Fredericksburg , VA 22403
*Items will not be returned unless return postage is included
I appreciate each and every one of you!! Thanks for hanging out with me - Ray .
.
Please check out my friends channel at / @collectingwatches - Навчання та стиль
Excellent video! Thanks for the information on the bar oil alignment holes and the chain gage.
Glad it was helpful!
From one Ray to another, good fix. 👍
Thanks Ray!
Great video, appreciate the attention to detail.
Thank you very much!
@@RayofallTrades+1
@@charleskelley-ih8tq thank you
GREAT video! Thank you! I could easily follow along and now my chainsaw works great again!
Glad it helped!
I have the same saw. I had a crack im my fuel tank vent line (pipe vent) i bought the same tune up kit you got on amazon. Originally all i changed was the fuel lines and primer bulb. Put back together and it ran horrible. Now it wont even start after several attempts. Was running perfect before i repaired the fuel lines. It has good spark, no pinched lines. No start. So i changed the carb too. Still no start. Not sure what went wrong. Do you have to adjust the idle and high/ low adjustment on these new carbs. Now im gonna have to take to the shop, which i cant afford to pay alot for repairs. Thanks for video. Any advice would be appreciated!
Does the primer bulb pull fuel? And can you use an eye dropper to add fuel directly into cylinder? If so, see if it momentarily fires. This will help determine if it's fuel related
@@RayofallTrades yes primer bulb primes fuel. I will try the eye dropper with fuel in the cylinder tomorrow and let you know. Thank you
hard to pull... how do you adjust valves on cs400. or can it be done?
No this is a 2 stroke. There aren't any valves. Hard to pull- I would pull the spark plug and see if it's any easier. If not, pull the muffler and look at the rings for scoring
i have the same saw today was working for 1 hour then stop working suddenly i try again it works only wen i push throller now is not working at all i feel the pulling engine wire its a little hard is any solution my saw almost new non use much very clean
It actually sounds like the oil /gas mix wasn't right. Thats usually the symptoms. You can pull the muffler and verify the piston condition
Can you tell me what the compression should be on a CS-450? I got 60psi. I think the owner didn't mix any oil with the gas.
I like to see around 120 or higher. Make sure choke and throttle are open when checking. You can pull the muffler off and check piston for scoring
Thanks. Great info.
If you look between the fuel tank and engine there is a breather. I thought the top line was an impulse line to
Oh cool. Thanks for the info!
how to connect the ignition coil to the swicth can show it the
diagram in pls
Sorry I don't have one right now. But the switch wire is just a circuit to ground which stops spark. You can use an ohm meter to see where the break is. Good luck
We have Gas Fuel Line Kit that may fit your equipment. We're happy to offer you the product completely free of charge in exchange for a video review. Do you need?
Please message me on roatrades@gmail.com
If you came here because your Echo chainsaw was working and now won't start, I recommend trying the technique shown in this video (no affiliation).
ua-cam.com/video/49Y8LWreDyA/v-deo.html
I own two Echos and sometimes have to do this after a saw has been sitting for a while. Not sure if it floods itself in storage or what.
I find you also want to be pretty sparing on using the primer bulb.
Good advice
I despise this brand. I wish I'd had just waited until Monday to buy a stihl. Pos flooded out the 3rd time i used it.
Oh no! Warranty available?
Quit blaming ethanol for everyrhing, you don't know what your talking about
Thanks for watching.