The garage need a solid surface. The mats will not be durable. The mats will sink once pressure is applied. Those tiles is for residential purpose ,and you appliyn Comercial load on them. Remove those tiles and lay concrete ,paint in Dark gray when finish. Dark gray will be easy to clean up after. Dark gray hide grease mark ,
@realpopcaan speaking from experience . Bought some and I had to put them in my son play area. The jack stand cut through it , and the wheels on the jack rip through it also when pressure reach it Excellent in the play room for the kids.
That wire is actually the worse you can use for grounding, its better you use 100% copper wire or battery wire, that kind of 0 gauge wirethey are not oxygen free hense allowing corrosion to easily access the wire.....just my silly advice still
That sound is either the bendix two part starter or the starter is not right it's hitting the flywheel? I'd say take out the Starter and see if it is performing correctly easy and if you have the old one check the head of the starter just see it check what I said and next time if it doesn't start bang it while the key is turned
Right….tear out the tiles. Your concrete floor is there already. It can be sanded flat removing all glue left from tiles. Then seal with epoxy staining dark with the car colors dark for clean up and looks.
![Lp. Сердце Вселенной #60 РОЖДЕНИЕ ЛОЛОЛОШКИ [Финал] • Майнкрафт](http://i.ytimg.com/vi/YoR0pAV9FVQ/mqdefault.jpg)
The garage need a solid surface. The mats will not be durable. The mats will sink once pressure is applied. Those tiles is for residential purpose ,and you appliyn Comercial load on them. Remove those tiles and lay concrete ,paint in Dark gray when finish. Dark gray will be easy to clean up after. Dark gray hide grease mark ,
Bless
Low the man bro, wah see how it work, a plan Fi buy the same thing fimmi garage 😂
@realpopcaan speaking from experience . Bought some and I had to put them in my son play area. The jack stand cut through it , and the wheels on the jack rip through it also when pressure reach it Excellent in the play room for the kids.
@ say less
sounds like the starter solenoid stuck
Having the same issue on my 68 chevy camaro on a relatively new Starter ,ran New ground same thing ,next up a relay
Do NOT use the sealer in the valvoline flush kit. It will clog the system. I was trained by Valvoline and they advised against it.
😁Asafa is the only celebrity in Jamaica that me see can do alot of things without getting someone to do it 👍💪
Excellent work 👍👏 💯% commitment, patience and perseverance ❤❤😂
Add a relay to starter and run a ground to the bolt that bolts the starter to the engine
Asafa i love how we're getting more car vlog and it getting longer
Best channel UA-cam GIVE DI MON AH PLACK.
Asafa.... did you know that your old starter can be reconditioned (new brushes etc.)right here in Jamaica for cheap?
The starter is working fine but yes I know starters can fix here
Sound like brush gone .. solenoid good.. replace n u good
The starter not meshing with flywheel or it not pushing out far enough to mesh with the flywheel
Use the black gym rubber material mats..as covering
Use the concrete and then seal it with the polymer
The starter need a Relay to boost the current
You need to get an electriction to make a outside startex on the car I think that will work
Wen u ready can link mi fi help wed the garage
Orange coolant you needed my boss 🤣
All gm after early 2000 use Orange or red
💯💯🔥🔥🔥
👍Asafa
That new starter could of just been faulty ive had that before where i had to take back 3 starters before getting one that would work
Where can I get that AC ?
eBay
Distilled water is fine for countries that dont need anti freeze
Welcome back
Hello to you Asafa and is Harder .
The starter need a relay
That wire is actually the worse you can use for grounding, its better you use 100% copper wire or battery wire, that kind of 0 gauge wirethey are not oxygen free hense allowing corrosion to easily access the wire.....just my silly advice still
The brush in the starter need to change plz sir u was lit at Roland dyno shoot out I was there for the first time
It seems that the "new starter" not good and the starter solenoid is the culprit is my guess.
That sound is either the bendix two part starter or the starter is not right it's hitting the flywheel? I'd say take out the Starter and see if it is performing correctly easy and if you have the old one check the head of the starter just see it check what I said and next time if it doesn't start bang it while the key is turned
Just put epoxy in the garage
Right….tear out the tiles. Your concrete floor is there already. It can be sanded flat removing all glue left from tiles. Then seal with epoxy staining dark with the car colors dark for clean up and looks.
Check if you have to shim that starter .... If i remember !
I think the new starter was defective because parts come defective a lot of times
The cooling system nah leak so why him a give u sealer ?
Hello to you Asafa and please reach out to me That starter can be repaired.
Boom
Instead using the jack on the titles, just cut a of plywood and put jack on it whenever using it
Next thing them start cuss me say that nuh safe 😂
@@Asafasub10😂😂
👊🏿👊🏿👊🏿👍🏿👍🏿👍🏿👍🏿
dont get garage tiles epoxy the floor the make epoxy kits for work garages
Probably the startex
The gear on the new starter not meshing properly with the flywheel
Just do the Epoxy
Saf check comments in last video , the starter needs to be adjusted with shims
Ok thanks I will try that for sure
Wanna built a 2zz police shape next year
New starter brush argument dun
Jesus bredda it's the flywheel..starter hitting ring gear or the gaps are incorrect
I told you it is the sadonite
epoxy the floor
The amateur in the stater not going out