I agree, it's DNR capabilities were my favorite. I think the algorithm they used with it was an improvement vs other Yaesu HF models. DNR is a great feature, amongst many other features the radio has
Hello! Page 71 of the manual states: Press the [V/M] key, if necessary, to enter the"Memory" mode.2. Press the [FUNC] key.3. Touch [GROUP].4. Rotate the [MULTI] knob to select the desiredMemory Group, then press the [MULTI] knob.5. Press the [FUNC] key, then touch [MEM CH].6. Rotate the [MULTI] knob to select the desiredMemory Channel within the Selected MemoryGroup. I hope this is of help to you as I do not have the radio anymore. Thanks
audio sounds better :) when i played with audio and making youtube videos i'd run about 6dB of compression and limit the output to -6dB. looks like your'e running around -3dB. at the beginning of your video and in a few spots i could hear some clipping which means your mic level in is a touch too hot. lower it a dB to start, add a few more dB compression in start there, if the overall output is low, then adjust the output or makeup gain, but careful not to overload youtube :) you want a whisper and yelling to be the same level, no distortion and with the threshold/depth set correctly. change the mic and you're back to the drawing board lol. good luck, 73 from 5 land.
Thank you. I think I figured out that it's better to change the volume at the mixer/usb interface (focusrite) instead of the software. I did hear that clips too. I really appreciate this input. I'll reference when I setup for three next video. I appreciate it, greatly.
@@HAMRADIODUDE no sweat! i'm not criticizing, just throwing out some ideas in case you haven't tried them, all the best! enjoy the rig! I'llget back in the hobby if i can ever get my grounding figured out.
I have no prob entering memories.. its when i attempt to exit memory and go back to vfo a and b that i encounter problems.. The memory always transfers into one of theVFOs.. then i panic and struggle to regain vfo a or b.. its my error, but i dont know what it is😏 Later: disregard.. i found my error🥴
Hi Sean, Are you saying that If I go to say 20m, it will not automatically select USB as the mode? My FT450 does that when I change bands. Stay safe. WJ3U
Don, I did say that, but since then: I have confirmed that if you tap the band button and don't select anything, it does have band registers. I should make a video on it soon. Also, did you say your FTDX10 does NOT have an issue with 150w at 12m? I'm understood my radio is going to possibly need to go in for service.
Ok Dude, got my FTDX10 today, my mouse is going really fast tried the setting but it won't settle down, also when I am in the settings places it will lock up and I am unable to get back using the button, I feel like a dweeb and of course I have not cracked the manual open yet. LOL
Thanks Dude. I love my FTDX10. The audio capabilities are astounding!
I agree, it's DNR capabilities were my favorite. I think the algorithm they used with it was an improvement vs other Yaesu HF models. DNR is a great feature, amongst many other features the radio has
I really appreciate this man, I'll have one some day.
(slow to responding to everything). I appreciate all your support. Patience is key. Sometimes things fall into place.
Ohhh yeah..memory group looks spiffee!!!!!....can't wait to have the "new arrival"..-73 Dave,k3dgr
Thanks!
Hey Thank You! I really appreciate this!
How do you change the memories to different memory groups?
Hello! Page 71 of the manual states: Press the [V/M] key, if necessary, to enter the"Memory" mode.2. Press the [FUNC] key.3. Touch [GROUP].4. Rotate the [MULTI] knob to select the desiredMemory Group, then press the [MULTI] knob.5. Press the [FUNC] key, then touch [MEM CH].6. Rotate the [MULTI] knob to select the desiredMemory Channel within the Selected MemoryGroup. I hope this is of help to you as I do not have the radio anymore. Thanks
What buttons do I press when loading from RT systems from the computer?
Unfortunately I don't more much about using that with rt systems. If it can't figure it out, the support over at RT is great
@@HAMRADIODUDE I figured it out. Pretty easy. Just plug in usb cord. Read radio first, then load new memories. No special key presses.
audio sounds better :) when i played with audio and making youtube videos i'd run about 6dB of compression and limit the output to -6dB. looks like your'e running around -3dB. at the beginning of your video and in a few spots i could hear some clipping which means your mic level in is a touch too hot. lower it a dB to start, add a few more dB compression in start there, if the overall output is low, then adjust the output or makeup gain, but careful not to overload youtube :) you want a whisper and yelling to be the same level, no distortion and with the threshold/depth set correctly. change the mic and you're back to the drawing board lol. good luck, 73 from 5 land.
Thank you. I think I figured out that it's better to change the volume at the mixer/usb interface (focusrite) instead of the software. I did hear that clips too. I really appreciate this input. I'll reference when I setup for three next video. I appreciate it, greatly.
@@HAMRADIODUDE no sweat! i'm not criticizing, just throwing out some ideas in case you haven't tried them, all the best! enjoy the rig! I'llget back in the hobby if i can ever get my grounding figured out.
Can you program splits for 10FM into memories?
The 101mp would nice. You can only listen to one person at a time, or is it just me
Do you have any videos on the FT991a?????
Hi , changing from 7.030 cw to 14.285 my dx 10 does change to usb, might be your ver. of software. Like ur videos. 73
Mine does as well. Don't know why he said that, might be a setting too.
I have no prob entering memories.. its when i attempt to exit memory and go back to vfo a and b that i encounter problems..
The memory always transfers into one of theVFOs.. then i panic and struggle to regain vfo a or b.. its my error, but i dont know what it is😏
Later: disregard.. i found my error🥴
What was the error? Just curious in case someone else comes up with the same type of troubles. Thanks.
it seems with this radio there are 3 ways to manipulate the radio
Hi Sean,
Are you saying that If I go to say 20m, it will not automatically select USB as the mode? My FT450 does that when I change bands. Stay safe. WJ3U
Don, I did say that, but since then: I have confirmed that if you tap the band button and don't select anything, it does have band registers. I should make a video on it soon. Also, did you say your FTDX10 does NOT have an issue with 150w at 12m? I'm understood my radio is going to possibly need to go in for service.
Ok Dude, got my FTDX10 today, my mouse is going really fast tried the setting but it won't settle down, also when I am in the settings places it will lock up and I am unable to get back using the button, I feel like a dweeb and of course I have not cracked the manual open yet. LOL