of course the minarelli is gonna have more torque it was designed to push a 500 pound scooter. the aluminum athena cylinder is better no cold seize issues
Aye, seen a couple of well intentioned but naive people slap those minarelli kits on mag wheel and skinny spoke wheels. Then they wonder why they get constant warping and breaking issues. Like you said, That immediate torque you get Vs the crappy Chinese factory cylinder/head combo is wild.
I have a Zeda 100. The 1st cylinder and piston broke. The piston pin retainer c clip snapped and got stuck between the piston and cylinder wall. I have replaced the cylinder and bought a windowed piston with a different type of c clip. I also put a reed valve and upgraded carb. It's been running really good. I live in a area with lots of hills.
I ran a yd 100 at 39 mph (GPS) with nt carburetor/ jet size .71?) and stock exhaust , with a 41T rear sprocket. The unbalanced bottom end vibrated excessively for enjoyable riding, to say the least.
I started out with the BT80. It's a shame the cylinder design has such insufficient cooling, because it really is a great quality motor overall. The high cylinder temp combined with the very short intake almost guaranteed it would vapor lock and stall on a hot day. I managed to reduce the heat a little by retarding timing, and running a thicker oil mix (25:1). Replacement cylinders were almost always out of stock, so I just gave up on it and replaced it with a generic 66/80cc that I ported and converted to case reed. It's more powerful than the BT80 and much more reliable, but I miss having the stator to keep my battery charged for my lights and accessories (just manually charge every couple of rides).
You didn't ask, but I'll give you my opinion, if you want it. I've had both, and I think the yd 100 is worth the money. It is faster, higher end parts, better carb. I have heard the bt 100 is the best of the 100's, but I haven't found one. I think you have to order it from another country, and s&h runs about $200.00l)
Good video bro and you’re right a lot of these are just a stock kit with an upgrade they’re not performance and that head that they’re selling with. It is junk I agree.
Great video, and thanks for the feedback! I actually purchased the Wildcat Plus Upgraded Ported PK80. Cylinder is ported as described, and the magnet is very strong. Did notice it was hitting the coil, but a quick readjustment fixed it. Muffler is not port matched. CM shipped mine in two separate boxes to keep the rate low, so I am still waiting for the 2nd one to arrive. Very eager here.
@oimpastato How goes the newer motor compared to the tofu dreg one you used to have ? If all the parts eventually arrived, it should be run in by now yes ?
I've been building these kits for about 20 years. I started when these were coming from China with a lot of the Russian part in the beginning. The only kid that was ever truthful was the 50cc or 48cc in truth. The 66/80 I never understood, and they always put cc after like it was an 80cc engine. I've looked at all the 100cc kits there still 66cc. They've gotten away with it for over 20 years.
In the west, the volume of a cylinder is calculated by using the formula Volume = Pi x Radius Squared x Stroke. However, in the east the displacement of an engine includes the area of the cylinder head's combustion chamber as well as the volume of the cylinder. Therein lies a discrepancy between measuring standards by the manufactures in China with those in the United States. However, all "100cc" engine kits on the market today are actually 78.6cc in displacement size if measuring by US standards.
@@tolanstout theres nothing wrong with "100cc" motors. If you don't like yd100s just get an ld100 cyl and cnc head. Never overheat built right can pull a 32t 50mph+
I would say is the best motorized bike website, definitely good for beginners, but eBay takes the cake for cheapest kits on the market.Glad they made the mineralli motor a cheap option for a mineralli,hard to get one below 300.Good Job and keep adding great products
Im looking at the ebay engines im debating on an 80cc vs a 100cc the 80cc has an nt carburator and the 100cc has the carburator with the red rectangular cover im curious if there is any difference in those carburators and im also curious if i will see any amount of performance increase with the extra 20cc and if so how much 20cc difference? Any info if you have it would be greatly appreciated
not gonna risk fucking up the cylinder tryna port it and i doubt a carb does anything to improve speed the only upgrades that make any difference is removing the exaust cap and air box maybe a smaller sprocket
@@randyrhodes9124 it should get you up to about 40mph. 32t might give you a bit more speed however it's definitely overgearing, you lose some torque, but it worked fine for me on my minarelli 26in wheels. 40mph 9krpm on 40t, 45 on 36, 50+ on 32, for me. could easily still climb up hills at about 40mph+
It gets very hot but if you aren't hammering down the throttle 247 you should be fine have a occ stingray and it runs great and fast never seized going on over 2 gallons of gas so far so a decent amount of miles
@@marcusprince3999 I had a yd100 fit fine you're going to have chain alignment issues I recommend getting the occ cmc motor mounts it alignes the motor to the left so it won't hit the back tire or break or slip off trust me it's a headache saver I think the bt100 is comparable to the yd 100 so u should be ok
Ive been building them for yrs, the only upgrade you need to double the Speed is use any chainsaw plug tho its alot shorter,my last one ran 28mph max but just by using a chainsaw plug it ran 60mph,I know people don't believe it can make that much a difference but it really does.also bike berry sux,poor customer service and, my 900 engine ready bike, frame pushed the frame mounted engine mounted thru the frame and broke into in 8 day, with a yr warranty they never made it up.
of course the minarelli is gonna have more torque it was designed to push a 500 pound scooter. the aluminum athena cylinder is better no cold seize issues
Aye, seen a couple of well intentioned but naive people slap those minarelli kits on mag wheel and skinny spoke wheels. Then they wonder why they get constant warping and breaking issues.
Like you said, That immediate torque you get Vs the crappy Chinese factory cylinder/head combo is wild.
I have a Zeda 100. The 1st cylinder and piston broke. The piston pin retainer c clip snapped and got stuck between the piston and cylinder wall. I have replaced the cylinder and bought a windowed piston with a different type of c clip. I also put a reed valve and upgraded carb. It's been running really good. I live in a area with lots of hills.
I got a Zeda 100 also. When they come stock the piston is installed the wrong way. Not sure if you flipped it or not.
I ran a yd 100 at 39 mph (GPS) with nt carburetor/ jet size .71?) and stock exhaust , with a 41T rear sprocket. The unbalanced bottom end vibrated excessively for enjoyable riding, to say the least.
Great video thanksb😁👍
Nice video, what mike did you use the audio sounds really good…
a yd 100 has a helluva lot more torque than a 66cc mine pulls any hill i point it at .watch for wrist pin clips
There is absolutely no point to buy that kind of motor that is over 50cc. It is just bicycle motor, 50cc is more than enough.
50cc is Never enough!🤣
I started out with the BT80. It's a shame the cylinder design has such insufficient cooling, because it really is a great quality motor overall. The high cylinder temp combined with the very short intake almost guaranteed it would vapor lock and stall on a hot day. I managed to reduce the heat a little by retarding timing, and running a thicker oil mix (25:1). Replacement cylinders were almost always out of stock, so I just gave up on it and replaced it with a generic 66/80cc that I ported and converted to case reed. It's more powerful than the BT80 and much more reliable, but I miss having the stator to keep my battery charged for my lights and accessories (just manually charge every couple of rides).
Thiers a few yd100 that r damn good
You didn't ask, but I'll give you my opinion, if you want it. I've had both, and I think the yd 100 is worth the money. It is faster, higher end parts, better carb. I have heard the bt 100 is the best of the 100's, but I haven't found one. I think you have to order it from another country, and s&h runs about $200.00l)
Good video bro and you’re right a lot of these are just a stock kit with an upgrade they’re not performance and that head that they’re selling with. It is junk I agree.
Not a good look to lie about the phanrom and upsell your own xrap.
I remember when bike berry was good but now it's basically a scam
*Is this **10:35** "Wildcat Minarelli 6 hp" really doing 6 hp?*
And is it really reliable?
Are there real positive feedbacks?
Yeah I bought a 100 CC engine and my 80 CC engine has way more get-up-and-go.
Great video, and thanks for the feedback! I actually purchased the Wildcat Plus Upgraded Ported PK80. Cylinder is ported as described, and the magnet is very strong. Did notice it was hitting the coil, but a quick readjustment fixed it. Muffler is not port matched. CM shipped mine in two separate boxes to keep the rate low, so I am still waiting for the 2nd one to arrive. Very eager here.
Did you end up receiving the 2nd box?
@oimpastato How goes the newer motor compared to the tofu dreg one you used to have ?
If all the parts eventually arrived, it should be run in by now yes ?
I've been building these kits for about 20 years. I started when these were coming from China with a lot of the Russian part in the beginning. The only kid that was ever truthful was the 50cc or 48cc in truth. The 66/80 I never understood, and they always put cc after like it was an 80cc engine. I've looked at all the 100cc kits there still 66cc. They've gotten away with it for over 20 years.
In the west, the volume of a cylinder is calculated by using the formula Volume = Pi x Radius Squared x Stroke. However, in the east the displacement of an engine includes the area of the cylinder head's combustion chamber as well as the volume of the cylinder. Therein lies a discrepancy between measuring standards by the manufactures in China with those in the United States. However, all "100cc" engine kits on the market today are actually 78.6cc in displacement size if measuring by US standards.
@@SyberSqueegy В России, мы никогда не добавляли объём камеры сгорания к объёму цилиндра.
Я про такое, слышу впервые от тебя.
@@jwserge You are correct. This is a china way of measurement.
Can you do anything to fix the inherent issues with the 100cc motors? Is the bottom end compatible with a 66/80cc or even a Minneralli top end?
@@tolanstout theres nothing wrong with "100cc" motors. If you don't like yd100s just get an ld100 cyl and cnc head. Never overheat built right can pull a 32t 50mph+
I heard a phantom 85 top end will fit on a cheap $80 USD 49mm iron sleeve bottom end. So about $180 for a ghetto phantom without the exhaust pipe.
It fits on a yd100 bottom end with a 50mm piston but all you need is the yd100 bottom end.
I heard wrong
@@JMB676 specifically the yd100 with a 12mm piston pin I believe.
Ghetto Phantom sounds like a low budget super hero 😂😂😂
I would say is the best motorized bike website, definitely good for beginners, but eBay takes the cake for cheapest kits on the market.Glad they made the mineralli motor a cheap option for a mineralli,hard to get one below 300.Good Job and keep adding great products
Dang it I just got a Zeda 80 and I didn't even know Cali motorbikes even exsisted
Im looking at the ebay engines im debating on an 80cc vs a 100cc the 80cc has an nt carburator and the 100cc has the carburator with the red rectangular cover im curious if there is any difference in those carburators and im also curious if i will see any amount of performance increase with the extra 20cc and if so how much 20cc difference? Any info if you have it would be greatly appreciated
What did you end up going with? I just bought a 66/80 from eBay for $90 and it seems good so far. Mine came with the Bofeng carb
Lot of these bikes motors are a scam, a few that are ok, trial and error
Can you advise a one - a "top notch" one?
The phantom 85cc is a performance motor
go buy a used weedeater easy install made in usa lots cheaper less headache
Love the videos Zane
a 50cc will top out at 35mph with 36t sprocket so paying 200 dollars more for an extra 5mph with a bigger motor aint worth it to me
just port it, upgrade carb and pipe etc and you'll get extra 15-20mph or more
not gonna risk fucking up the cylinder tryna port it and i doubt a carb does anything to improve speed the only upgrades that make any difference is removing the exaust cap and air box maybe a smaller sprocket
i put a 40t sprocket on it and got it to 34mph so i was thinking maybe a 36t would get me to 37 38mph?
@@randyrhodes9124 it should get you up to about 40mph. 32t might give you a bit more speed however it's definitely overgearing, you lose some torque, but it worked fine for me on my minarelli 26in wheels. 40mph 9krpm on 40t, 45 on 36, 50+ on 32, for me. could easily still climb up hills at about 40mph+
6hp can do 45 mph.
Is it not worthy of that?
I wrote a topic on this on my motorbike community page but you nailed it. G.j.
A cast iron minarell gets to hot
Widecat not true 40mm la hover has video he bought one tore it down and measured the crank he say it was 39.2
Yes it’s actually a 39.5mm
It gets very hot but if you aren't hammering down the throttle 247 you should be fine have a occ stingray and it runs great and fast never seized going on over 2 gallons of gas so far so a decent amount of miles
@worldme8153 I'm putting engine on an OCC soon. Im wondering if the new BT 100 Version 2 wull fit? Which engine did you use?
@@marcusprince3999 I had a yd100 fit fine you're going to have chain alignment issues I recommend getting the occ cmc motor mounts it alignes the motor to the left so it won't hit the back tire or break or slip off trust me it's a headache saver I think the bt100 is comparable to the yd 100 so u should be ok
@@marcusprince3999 And right now I have a minarelli which I wouldn't recommend but I have a pedal chopper which is much more sturdy
I'm interested in the wild pk80 with a race head I saw on ebay is it worth the buc ?
super useful tips on the good parts to look out for; thanks.
what about Vostro
thats the only brand we have in my country
a phantom always blows up
Thanx for info, new to hobby
Ive been building them for yrs, the only upgrade you need to double the Speed is use any chainsaw plug tho its alot shorter,my last one ran 28mph max but just by using a chainsaw plug it ran 60mph,I know people don't believe it can make that much a difference but it really does.also bike berry sux,poor customer service and, my 900 engine ready bike, frame pushed the frame mounted engine mounted thru the frame and broke into in 8 day, with a yr warranty they never made it up.
What do you mean chainsaw "plug" ??
What do you mean chainsaw "plug" ??
@@jwserge Thats the same Spark Plug that is used in a Chainsaw!!!🤣
Dude you must really really high or full of BS....Did you post this comment on April 1st?
wrong
Please elaborate.
I mean yes and no because you can get more performance form just a big carbrater