How To Install Rear Wheel Bearing & Hub Assembly 2004-2010 Toyota Sienna
Вставка
- Опубліковано 4 лис 2024
- Buy Now!
New Wheel Bearing & Hub Assembly from 1AAuto.com trq.video/ia-1...
Not only can a worn wheel bearing or hub be annoying if it is noisy or vibrating, but it can also lead to accelerated wear in other parts, or unsafe driving conditions. Replacing your worn bearing or hub with a quality TRQ part is a safe, smart, decision. This video shows you how to install a new wheel hub and bearing on your 2011-2016 Ford Super Duty F-350.
• Check here for more videos on the 1998-2008 Ford Super Duty: • Ford Super Duty F-350 ...
This repair was done on a 2006 Toyota Sienna LE 3.3L and the process should be similar on the following vehicles:
2004 Toyota Sienna
2005 Toyota Sienna
2006 Toyota Sienna
2007 Toyota Sienna
2008 Toyota Sienna
2009 Toyota Sienna
2010 Toyota Sienna
Tools you will need:
• Flat Blade Screwdriver trq.video/ob3-...
• Pry Bar trq.video/o6-1...
• 14mm Wrench trq.video/o7-1...
• 14mm Socket trq.video/obU-...
• 17mm Socket trq.video/obU-...
• 21mm Socket
• Brake Caliper Hanger trq.video/oh-1...
• Slide Hammer
• Pliers
• 3/8 Inch Impact Gun
• 3/8 Inch Breaker Bar
• Socket Driver
• Torque Wrench trq.video/oaZ-...
• Copper Anti-Seize
• Center Punch trq.video/or-1...
• Floor Jack trq.video/oac-...
• Hammer
• Jack Stands trq.video/o8-1...
• Pick trq.video/oS-1...
• Wire Brush trq.video/oy-1...
Subscribe: / @trq
Check out our playlist:
Toyota Sienna 2004-2010 2nd Generation: • Toyota Sienna 2004-201...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
Followed this video to the T and was able to replace a really bad bearing within a couple hours. Took a half hour of using th slide hammer but it finally popped out and had the new one in pretty quickly. Can’t thank you enough.
Just did this and used the TRQ parts. Worked great. The bolt used at 2:00 minutes to remove the rotor is an M8-1.0 (I bought a 30mm bolt at Home Depot) . Great video and this saved me $850 compared to the auto shop. The van rides quiet once again. I replaced both, The passenger side was definitely bad.
did you need the slide hammer?
Great Vid. Helped alot. Thanks!
Dang! that looked easy! Thanks!
You forgot to mention plug the cable back up that was disconnected in the 1st disassembled steps
Great vid! Thanks very much!!
My hub wont seperate from the back plate/, i believe rust is holding it together. The whole thing is coming out including brakeshoes assembly
Do the methods in the video work on Sienna's in the salty roads of North Eastern US? Very rusty and highly corrosive environment up here.
Gracias me llegó este tarde yo ya lo hice gracias es fácil sigan paso a paso este video
Easy peasy 😊
Any idea if this is the same for a 2011 sienna SE FWD?