TeraFlex Install: 231 Extreme Short Shaft Kit (4444400) Plus 2WD Low Range Kit (2204000)
Вставка
- Опубліковано 5 лют 2013
- teraflex.com/tj-np231-extreme...
teraflex.com/tj-np231-j-2low-...
We give an 1998 TJ a boost by installing a 231 Extreme Short Shaft Kit, while we were at it we threw in a 2WD Low Range Kit. Check out the install. - Авто та транспорт
Glad to see an aftermarket solution that enable 2WD Low. The last vehicle I drove that you could do this with was my Dad's `89 F-150, 2L was accomplished by just leaving the front hubs unlocked and pulling the transfer case lever back to 4L. It is great when you are 12 years old and need to move a truck with a manual transmission through the yard. Or teaching someone how to drive a manual transmission and getting them used to the clutch pedal before introducing the gas pedal. Or maneuvering a trailer in a tight area where low speed and not binding the steering helps out a lot.
This video wasn’t exactly specific to my application but it was a tremendous help. The Extreme Short Shaft kit came with everything I needed to get the job done. Outstanding work on this video, it made my project possible and I am truly appreciative!
This is one of the best of not the best install video I have ever seen.
That was a great video!! Looks like I did mine the right way as well! It's a fun upgrade to do and fixes the vibration issues associated with a suspension lift. I also upgraded with adjustable upper control arms to tilt the axle angle.
best install vid ive ever watched
If you sell parts you need videos like this!
and2244rew no kidding ! A lot more people would be less intimidated to buy products if they see how easy it is to install
A short shaft or SYE helps to correct your driveling angle by allowing you to run a longer driveshaft in a lifted Jeep.
Is there any videos showing the use of the 2wd low kit? I want to see how it operates on the trail.
This a really good video... got me
Why does the new yoke push back into the transfer case when you are installing the rear driveshaft? that cant be correct? And why does the tone ring hit the pump? cause it does in the kit I just put in.
Why do you say the tone rig will spin freely when the instructions say to insert the tone ring dowel into shaft?
Wow, great video and I'm really glad you put that one out. Now I know never to do that one myself
where in sam hell did they get those awesome snap ring pliers! i did this with traditional ones and those snap rings drove me to the edge of reason
they look like modified regular ones
Nice!!
Actually the instructions mention not refilling the transfer case for 24hrs to let the silicon sealant set up properly..
Muito bom!!!
Yes, TeraFlex makes a JK Rubicon 2Low #2266900 $265.99.
I have an 08 Rubicon. Can I put the 2WD Low in the transfer case. Without doing the short shaft? What will it do for me? Not sure how it works. ?
Great music
is it possible to buy a replacement rear output seal from a local autoparts store? I already ordered one from you guys but i need it sooner
Fill plug, then the drain plug, this is 101
Do you have 2WD low for 2013 2DR sport ?
Wow
Do you have to program the speed sensor after install? I just got a TJ that has this kit in it but the speedometer doesn’t work.
What is this short shaft for
hey clean up that rust under the belly pan! Those nutserts are going to rust out, trust me hehe.
do you need new driveline shafts if you do the SYE?
Yes. You'll need a longer drive shaft if you're doing the super short SYE.
So i would need to buy a longer drive shaft then? Are you selling them?
I just bought the teraflex super short sye but, i cant find the cv driveshaft to work with that sye, or the normal cv driveshaft that works with the normal sye is going to work with my teraflex super short sye???
This kit must be used w/ a CV style (double cardan) driveshaft. Talk to your a driveshaft specialist for options to match your lift.
currently having a problem with my speedometer. stays at zero. i replace the sensor didn't do anything to help. if you have advice on what to try next that would be wonderful thx.
Sometimes the yoke nut gets loose enough to allow the tone ring to slip or even spin freely. If your speedo all of a sudden stopped, it may just be a loose yoke nut. If that doesn't work give us a call and we can help diagnose the issue. 801-713-3314
How does the speed sensor account for bigger tires and different gear ratios?
You will need to install a TruSpeed Unit to adjust for the new bigger tires/gears.
***** You need to figure out what gear you need, depending on tire size and gear ratio etc, and replace the 'speed-o gear' on the speed-o gear assembly (which will cost about $15-20. Check on Jeep forums and google. There's tons of articles on how to do this.
Can I use a spare front drive line for the sye kit on a 93 jeep Cherokee xj
This kit must be used w/ a CV style (double cardan) driveshaft.
Forgot to refill the transfer case fluid! Doh!
Silicone is for bathrooms and sex toys it shouldn't come anywhere near a vehicle. Why, because it's 2015 theres better stuff available. It's called anerobic gasket maker, it outperforms silicone in every way except filling gaps. It's seals better, it's easier to remove the old stuff and it only cures in the absence of oxegen. Only what's sandwiched in between the parts cures so even if you use too much there is nothing to plug pick-up screens. The permatex part number for the small tube is 51813.
I use The Right Stuff. Seals everything!
Any reason why after install of the 2 lo kit it won't shift out of 2hi to any mode?
Installed incorrectly.
13:24 Now that is a liberal amount of Loctite.
Do you make these for XJs?
Same t case
they left out aa important step, the last thing you need to do is to tighten the nuts back down on the transmission mount to the belly pan.
+Luke Webb And refill the T-Case with oil!
se olvido del aceite de caja..!!
Can this go in a 97 jeep xj
Technically yes, but we would recommend the short shaft kit - 4444401.
Sorry we only have these for Rubicons.
Any car
Just as a heads-up to anyone, do NOT buy channellock pliers. They are 100% pure garbage.
You absolutely must buy the Wilde 9" external lock ring pliers, or any good tool brand (matco, snap on).
Turned an easy project into an absolute nightmare. Whoever designed those pliers needs their hands cut off and eyes gouged out so they can't under engineer anything again.
I feel this way about lots of stuff lol
I make Brakleen & that's not what it looks like.
Anyone else cringe every time you see a professional using a chrome socket with an impact?
Why , does the glare bother you ?