Dishwasher Drain Pump Continuity Testing
Вставка
- Опубліковано 28 сер 2024
- Dishwasher not draining? This video demonstrates how to test a drain pump on a dishwasher. The drain pump sends water into the sink drain or garbage disposer after each wash cycle, so a bad pump could cause the dishwasher to not drain properly.
Other commonly replaced parts for a dishwasher that won’t start are:
Thermal fuse
Door latch
Main control board
Touchpad and control panel
Touchpad
Timer
Click here to purchase a replacement dishwasher three terminal switch:
www.repairclin...
Click here to purchase the multimeter used in this part testing video:
www.repairclini...
How to disassemble your dishwasher:
• Frigidaire Dishwasher ...
For more DIY videos including part replacement and help finding your model visit the repair help section of our website:
www.repairclini...
All of the information provided in this part testing video is applicable to the following brands:
Asko, Bosch, Frigidaire, GE, Kenmore, KitchenAid, LG, Maytag, Whirlpool
Connect With Us!
plus.google.co...
/ repairclinic
/ repairclinic
/ repairclinic
Join our free VIP email list for discounts and money-saving tips: tinyurl.com/pnn...
Check out our blog: www.DIY.RepairC...
Don't forget to like and comment on this video, and subscribe to our channel!
Please read. My experience. Water not drained. I checked hoses. They looked clean and clear. So I wasn’t worry about it. Following the video I decided to buy a multimeter. Checked the water pump for continuity and “Everything ok” like 26 ohms. I still decided to order a new pump from Amazon for $29. Installed it and it works flawlessly. My dishwasher was pretty noisy when new because it has a new and strong draining pump. Last days it was doing very quiet cycles due to, what techs call it, a “tired pump”. Now. At least in my Whirlpool model, I didn’t have to disconnect or remove it from its place and put it upside down. I only remove a plastic cover from the bottom front and squeezed my hands through it. Very ease. First. Disconnect the power. Vacuum all the water. Using pliers, Disconnect the plastic drain hose that goes to the pump. And then. With a mirror. Locate the clip that goes on the other side of the pump. Press it and rotate the pump and voila. Clean and make sure there’s nothing obstructed. Disconnect the electrical plug and connect the new one. Easy peasy. I hope this helps. Salud 🍻🍻🍻
Love this guys voice😂 , his vids are always very helpful.
Best guide ever!!! Thanks you.
15-40 Ohm? Probably for this particular motor. Mine Bosch 90Ohm, some go over 200
My "broken" one only measured 7 ohms, but the new one just arrived also shows 7 ohms with reversed polarity
I have a newer GE portable dishwasher GPT225SSL0SS. It has drain pump part number WD19X24651. It tests 28 ohms and the impeller turns fine by hand. No junk lodging it and the impeller blades look fine. Rinsed the drain filters (fine and coarse) inside of the cabinet. They looked ok beforehand, though. Glass filter is clean. Sump assy. looks clean.
It's been having trouble draining lately. Sometimes leaves an inch of water in the bottom when finished. Sometimes it finishes fine. Lately, if I restart a new clean cycle from scratch, it will pump out the old water first, and then start filling normally. Today, it wouldn't even do that and 888 errored out. I'm running it again now after taking it all apart.
I'm wondering if the User Interface Control Assembly WD21X28718 in the top of the door is acting up. Looks like a $68 part.
Make sure the drain hoes has a loop in the end by the garbage disposal
Great video, helped so much!!
What happens if you have three wires going into your drain pump? What is the third wires for?