very good video. Step by step, I just used it synchronously. Without this information I would probably have broken something, especially at the beginning. Thank you very much 😀
Highly appreciated video, great to have someone showing how to do it. I checked the reel since I had no connection and noticed that one of the wires that runs on the side of the cord reel where broken in the corner (at the 90-degree bend) where the wire goes into the center. A quick solder fixed my problem. Probably some tension on the cable/wire that caused it. I wonder if this is a common problem. Please write here if you have the same problem.
Hi, I had this problem maybe once out of 200+ cable reel problems, most of time ppl damage cable near the plug or near the reel, sometimes between that. In compare to Zelmer/Bosch cable reels, Electrolux has better part (but wind mechanism is opposite, winding stops working earlier) 🤔
My suggestion is: when you put in a new cable part, you immediately check if it rewinds. You do this by pushing the pin - the metal wire / part on the top. Otherwise, you might almost assemble the vacuum cleaner only to realise your cable doesn't rewind.
@proexservis My experience is the following: I put the spare part easily back, but I forgot to check whether the cable rewinds. Only after disassembling the vacuum cleaner again, I realised the part can easily be put back in a faulty way. This is when the bottom right part is not entirely or properly put / slid in a "cradle". If this happens the frame of the cable blocks the cable. At the end all went well. Thanks again for this video.
Interesting video, thank you for it! Excuse me, is this a common issue for these series (including the "Green" version)? Cause this is not the only video I found about how to replace their cord reel part...
@SoldierOfSunrise hi, thank you too 👍 No, on this model most often will break plastic regulator or pcb stops working. Cord winder is the same as on 90% of Electrolux vacuum cleaners, so nothing special, cable is not thick enough to survive more years (5+) if you dont hold cable during rewinding to slow it little bit (or if you hold cable reel button with no stops then it can damage cable if it is in bad position for too long inside of vacuum cleaner +fast rewinding can damage reel spring) - but if you take care of this then it can work longer than its motor, more often owner damage cable by pulling it too strong out (when cable stuck somewhere or when entire cable is already out of vacuum) or by pets 🫣
@@proexservis , thank you so much for the quick response, and the useful info! Excuse me, but could you help me for a while in my decision? My current vacuum cleaner has gone wrong, and I'm fed up with the extreme prices of their accessories, so I'm close to go back to the "good old" Electrolux. (That is why I'm watching these videos on UA-cam right now.) I see, thati n my country (Hungary), at the official Electrolux shop the Hungarian made UltraOne, the UltraOne Green, UltraSilencer, and the D8, D9 models are still available for purchase. But I realized, that the company moved the production to China (not a good news to me), and that new 300,500,600, 800 series of course are sold in all kind of setups. (I wonder how long those recycled plastic housing would last without a break... 2 years? 3 years? 😒🙄 ) What do you think, please, which would be the right choice! To help your answer: I don't care about noise level. The main criterias to me are: - the possible best dust filtering, - Possible best vacuum power, - And I don't mind, if It wont break in 3 years, so would last at least 4-5 years expectedly. (I know, any additional working time beyond 2-3 years is sadly a present for all nowadays' echnological products for households.) (Of course there are "good to have" attributes as well - e.g. possibly the longest cord - , but the above 3 criterias are the most important.) So which would be the right choice, please? UltraOne, UltraOneGreen, D8-9 or one of the new x000 models made in China? Your help is much appreciated! (If the great ESP74DB was still available as new item, it would not be a question to me. But now, I'm sorry, I cannot decide.)
Because of recycled plastic and because of that every part was already made in china (except motors - slovenia), it was reasonable to move whole production to china, in these cases it is not problem: pure d8/d9 or same but newer electrolux 800 But I would pick Ultrasilencer EUSC (because of hose connection from top of the lid, radius same as EUO/PD8/9, filtration, noise volume better than EUO but not as PD9/E800 and because of long history of US, this model was designed in 2013, so very capable and spare parts are available for over decade) then ultraone and then pured8/9/electrolux800 (because of higher price). Electrolux 300/500 is old EasyGo (overpriced 60-80€ model), only Electrolux 600 is new model (it is some new chinese design, but not great as US/UO/PD: ua-cam.com/video/QaqfSihFIOs/v-deo.htmlsi=NdzEU8zhGvuFpS3V).
@@proexservis , thank you so much! I highly appreciate your knowledge and willingness to help! 🙏 (BTW... the linked comparison of the 3 models was the 1st video I've checked, when I was searching for info about the new Elux models on UA-cam. 🙂 ) Unfortunately meantime in the official Electrolux shop, the UltraSilencer became "out of stock". 😥(Won't get restocked, I'm afraid. Their "summer sale" is ongoing...) - Do you think, that hose connection on the front of the machine (like UltraOne or D8/9) has a disadvantage? If yes, what is that comparing to the "top of the lid" connection type? 🤔 - You are right, as Pure D8/9, and Ultimate 800 are too expensive for me. So currently these are the available models and options for me: 1. EUOC94DB - UltraOne 66 dB - 166 EURO, 2. EUOC9GREEN - UltraOne 66 dB - 172 EURO, 3. EB61A5UG - Animal 600 73 dB - 139,5 EURO, Also, there are 4. EPF62IS PowerForce - 154 EURO, 5. PF61RR PowerForce - 86 EURO. So considering everything, which is the best product I should choose, please?
Last US has tech. documentation from 2022, so maybe there is still chance they will produce this line as it is or under new name, i wish 🤔 for example last EPF (powerforce) has docs from 2020 and is still in stock Hose in front (in my opinion) is bad for action radius, damaging hose when you are pulling it behind during vacuuming and dust/dirt in bag is always in that hose connection if you are using bag till its maximum 😅 but it is true that UO has advantage over US, can use more space of bigger E210 s-bag. Some shops are still selling UltraSilencers, but dont pick EB61 over UO or PF (this one only if you dont mind less cable length). EUOC or EUOCGreen, doesnt matter too much, one is produced with 50-70% recycled plastic and one is normal, pick by colour preference or go “eko”, those few plastic doesnt save anything when you compare it to big chunk of plastic in everyday usage 🫣
very good video.
Step by step, I just used it synchronously.
Without this information I would probably have broken something, especially at the beginning. Thank you very much 😀
Highly appreciated video, great to have someone showing how to do it. I checked the reel since I had no connection and noticed that one of the wires that runs on the side of the cord reel where broken in the corner (at the 90-degree bend) where the wire goes into the center. A quick solder fixed my problem. Probably some tension on the cable/wire that caused it. I wonder if this is a common problem. Please write here if you have the same problem.
Hi, I had this problem maybe once out of 200+ cable reel problems, most of time ppl damage cable near the plug or near the reel, sometimes between that. In compare to Zelmer/Bosch cable reels, Electrolux has better part (but wind mechanism is opposite, winding stops working earlier) 🤔
My suggestion is: when you put in a new cable part, you immediately check if it rewinds. You do this by pushing the pin - the metal wire / part on the top. Otherwise, you might almost assemble the vacuum cleaner only to realise your cable doesn't rewind.
Maybe 1 out of 100/200 is faulty part, but I am checking it through assembling 🫡 because every plastic part have to fit in another part, like in 11:55
@proexservis My experience is the following: I put the spare part easily back, but I forgot to check whether the cable rewinds. Only after disassembling the vacuum cleaner again, I realised the part can easily be put back in a faulty way. This is when the bottom right part is not entirely or properly put / slid in a "cradle". If this happens the frame of the cable blocks the cable. At the end all went well. Thanks again for this video.
Thank you very much! You saved my vacuum cleaner - and my day! 🙂
Nice, thank you 👍
Excellent!
Interesting video, thank you for it! Excuse me, is this a common issue for these series (including the "Green" version)? Cause this is not the only video I found about how to replace their cord reel part...
@SoldierOfSunrise hi, thank you too 👍
No, on this model most often will break plastic regulator or pcb stops working. Cord winder is the same as on 90% of Electrolux vacuum cleaners, so nothing special, cable is not thick enough to survive more years (5+) if you dont hold cable during rewinding to slow it little bit (or if you hold cable reel button with no stops then it can damage cable if it is in bad position for too long inside of vacuum cleaner +fast rewinding can damage reel spring) - but if you take care of this then it can work longer than its motor, more often owner damage cable by pulling it too strong out (when cable stuck somewhere or when entire cable is already out of vacuum) or by pets 🫣
@@proexservis , thank you so much for the quick response, and the useful info!
Excuse me, but could you help me for a while in my decision? My current vacuum cleaner has gone wrong, and I'm fed up with the extreme prices of their accessories, so I'm close to go back to the "good old" Electrolux. (That is why I'm watching these videos on UA-cam right now.)
I see, thati n my country (Hungary), at the official Electrolux shop the Hungarian made UltraOne, the UltraOne Green, UltraSilencer, and the D8, D9 models are still available for purchase.
But I realized, that the company moved the production to China (not a good news to me), and that new 300,500,600, 800 series of course are sold in all kind of setups. (I wonder how long those recycled plastic housing would last without a break... 2 years? 3 years? 😒🙄 )
What do you think, please, which would be the right choice! To help your answer: I don't care about noise level. The main criterias to me are:
- the possible best dust filtering,
- Possible best vacuum power,
- And I don't mind, if It wont break in 3 years, so would last at least 4-5 years expectedly. (I know, any additional working time beyond 2-3 years is sadly a present for all nowadays' echnological products for households.)
(Of course there are "good to have" attributes as well - e.g. possibly the longest cord - , but the above 3 criterias are the most important.)
So which would be the right choice, please? UltraOne, UltraOneGreen, D8-9 or one of the new x000 models made in China? Your help is much appreciated!
(If the great ESP74DB was still available as new item, it would not be a question to me. But now, I'm sorry, I cannot decide.)
Because of recycled plastic and because of that every part was already made in china (except motors - slovenia), it was reasonable to move whole production to china, in these cases it is not problem: pure d8/d9 or same but newer electrolux 800
But I would pick Ultrasilencer EUSC (because of hose connection from top of the lid, radius same as EUO/PD8/9, filtration, noise volume better than EUO but not as PD9/E800 and because of long history of US, this model was designed in 2013, so very capable and spare parts are available for over decade) then ultraone and then pured8/9/electrolux800 (because of higher price). Electrolux 300/500 is old EasyGo (overpriced 60-80€ model), only Electrolux 600 is new model (it is some new chinese design, but not great as US/UO/PD: ua-cam.com/video/QaqfSihFIOs/v-deo.htmlsi=NdzEU8zhGvuFpS3V).
@@proexservis , thank you so much! I highly appreciate your knowledge and willingness to help! 🙏 (BTW... the linked comparison of the 3 models was the 1st video I've checked, when I was searching for info about the new Elux models on UA-cam. 🙂 )
Unfortunately meantime in the official Electrolux shop, the UltraSilencer became "out of stock". 😥(Won't get restocked, I'm afraid. Their "summer sale" is ongoing...)
- Do you think, that hose connection on the front of the machine (like UltraOne or D8/9) has a disadvantage? If yes, what is that comparing to the "top of the lid" connection type? 🤔
- You are right, as Pure D8/9, and Ultimate 800 are too expensive for me. So currently these are the available models and options for me:
1. EUOC94DB - UltraOne 66 dB - 166 EURO,
2. EUOC9GREEN - UltraOne 66 dB - 172 EURO,
3. EB61A5UG - Animal 600 73 dB - 139,5 EURO,
Also, there are
4. EPF62IS PowerForce - 154 EURO,
5. PF61RR PowerForce - 86 EURO.
So considering everything, which is the best product I should choose, please?
Last US has tech. documentation from 2022, so maybe there is still chance they will produce this line as it is or under new name, i wish 🤔 for example last EPF (powerforce) has docs from 2020 and is still in stock
Hose in front (in my opinion) is bad for action radius, damaging hose when you are pulling it behind during vacuuming and dust/dirt in bag is always in that hose connection if you are using bag till its maximum 😅 but it is true that UO has advantage over US, can use more space of bigger E210 s-bag.
Some shops are still selling UltraSilencers, but dont pick EB61 over UO or PF (this one only if you dont mind less cable length). EUOC or EUOCGreen, doesnt matter too much, one is produced with 50-70% recycled plastic and one is normal, pick by colour preference or go “eko”, those few plastic doesnt save anything when you compare it to big chunk of plastic in everyday usage 🫣
Thank you very much!
Thanks
طريقة الانتخاب الاتحاد الأوروبي