🚘 "Illuminate Your Ride: Effortless Rear Map/Dome Light Removal for a 2011 Toyota Venza & Camry 2011
Вставка
- Опубліковано 17 вер 2024
- 💡 Brighten Your Drive: Easy Rear Map/Dome Light Removal & Bulb Replacement for 2011 Toyota Venza & Camry! 💡
👉 Master this simple DIY task and enhance your car's interior lighting!
#ToyotaVenza #ToyotaCamry #CarMaintenance
Learn how to effortlessly remove the rear map/dome light cover and change the rear map light bulbs for your 2011 Toyota Venza. This method also applies to other cars like the 2011 Toyota Camry with the same rear map light cover.
🛠️ Trim Kit Used in the Video: ▶︎
★ amzn.to/3jdknX2 ★
While you may not need a kit this extensive, it can also come in handy for replacing plastic rivets missing from other vehicles.
🌟 SPECIAL NOTE: My video focuses on removing the cover, but for a tutorial on removing the bulbs, check out this helpful video:
🏃🏾 • Rear map light Camry 2...
👉 Tell them we sent you! 👈
🛑 Disclaimer: It is safe to assume that I may receive a small commission for recommending this product. However, I do so with confidence because I have used it, and it worked for me. It's no additional cost to you, you are helping to support this channel and it is greatly appreciated. 🙏🏾
I may not be an expert, but I'm thrilled to share the practical knowledge I've acquired. Let's keep our cars in top shape together!
Not all hero’s wear a cape. Thank you sir!
Thank you for the help with this 🙏 Just did my 2014 Venza Limited. 😁👍🏼👍🏼👍🏼
Great job bro. I'm a fan
Thanks, I appreciate that.
Thank you!
You are welcome I hope It helped.
What's the 1 thing you love most about your VENZA???
Leave your answer in the comments below...
They've thought of everything for convenience.
Thanks for the video, would never have done it without breaking something. Any idea on how to replace the glove box light?
I changed mine today, take the glove box out by disconnecting the shock on the right side, pull the sides of the box inward and it should come all the way down. This exposes the 3 screws on the top and 1 on the bottom. There is a 10mm bolt on the right side that may need to come out, I didn't take It out. Remove all the screws and pull the housing down, this will un-clip it allowing you to get access to the bulb housing. The bulb sits inside the glove box light switch. Press the 2 tabs inward and pull the switch. This will remove the switch housing. Disconnect it and now you can replace the glove box light. Use a needle nose plier to remove the bulb. Installation is reverse. Took me about 20 min, best of luck!
Thanks, I'll give it a try.
The issue I have since owning my 2010 Venza (purchased pre-owned in 2012) is the dome light housing will detach from the roof starting with the edge towards the back and if I don’t catch it early (every 3-4 days) the whole unit will eventually hang by the wires.
Nice video but still didn't give me an exact way to get the light out and when I did I can't put it back in and it was so annoying for me after it kept dropping I chopped off the wires for the time being 😂
Where's the link to the other video to replace the bulbs?
ua-cam.com/video/cJ-j2YTd0S0/v-deo.html
Thats the link he provided if u did not see it under his note
I found this one was easier for me. The clips were too hard for me. I changed all my dome lights in my 2009 Toyota I went through so many video. This one was helpful with figuring out how to take off the dome in the back seat. Then I click the video this guy posted about the light bulb which to press on the 4 clips but it was so hard for me then I ran into this other video made it a little more easier. Here u go
ua-cam.com/video/MTeyi19cAac/v-deo.html