The heat is disabled... Its tropical here in Philippines... But if you need to have itworking... You will need tge other two motor actuator for mode and cold/heater.... The electrical is all plug and play as long as you have the motor actuators...
Got it thanks, I'm from Cambodia so I know all out the heat. So you didn't change the computer or anything, correct. I see where you butt spice the plugs for the fan switches. If I replace the hardness I don't have to spice them, correct.
@@du3dsp I've heard it's a direct swap from the bicycle brake line original but after I squeeze my fat american ass down in there and I'm looking at it upside down, I just cant visualize how it goes on..
Great video! How did you convert the manual temperature cord cable to electrical knob? Between the two air vents there is a manual arm switch that allow you to choose if the air is going to the windshield or to the front air vent , what did you do with that arm switch?
So far yavent touch much... Only the harness... The climate control... Did conversion on the hazard switch...so far thats it... Most of the harness is plug and play...
as far as when i put the sockets plug and play sya... nagkaron lang ako ng slight modification para saresistor block... and rewiring sa hazard switch... fyi usdm yung 2 din ha... sa jdm medyo masalimuot ang conversion...
Ginamit ko lang po yung resistor block na kasama... Yung nilalakihan ang butas d7n sa may blower housing... Ako dun sa may circulate/intake damper side nilagay since isinara ko na yung intake side...
Hi sir un po bang resistor block saan nyo po kinabit doon po ba kung saan nakalagay ung sa stock or nilipat nyo ng location? At sa hazard switch socket ano po ang rewirig na ginawa, kinakabit ko po ngayon ung sa akin
Hello sir... Actually di po ako shop... Hobby lang and for tutorial purpose lang po mga videos ko... Pero sa Malolos Bulacan po lacation ko if you need any help...
Very informative content sir from you safety management and crowd management.
Thank you very much mam... Nice to see you here in the channel...
This is just what i needed fo find. I have a Honda civic 1999(EJ9) chasis, the 1.4is model, does the vents position works?
Yes, it did work.
How did you get the heat to work without changing the motor, because the 98 has cable and 99 or newer is electronic?
The heat is disabled... Its tropical here in Philippines... But if you need to have itworking... You will need tge other two motor actuator for mode and cold/heater.... The electrical is all plug and play as long as you have the motor actuators...
Got it thanks, I'm from Cambodia so I know all out the heat. So you didn't change the computer or anything, correct. I see where you butt spice the plugs for the fan switches. If I replace the hardness I don't have to spice them, correct.
Correct... But you need to modify the wiring for the hazard switch as well...
Ok, thank so much for information 🙏.
Amazing ,
what a job for making EK3 more modern !
Thank you mate...
can i ship this Lcd android ? i have just the control bezel without lcd ,, more details please for the size and reference ,,
thank you dear
Hello there, where is your location? The lcd i intalled was purchased online... You can easily get one from amazon...
Morroco , did you have the name or , store link ? thnak's @@du3dsp
what about the ac wiring it work with the old wiring or there som changing? plzzzzzzz i wana know
It works the same way with the old... Only to modify the hazzard switch and rar windshield heater...
Hi friend, I did this in my USDM Ek but I lost AC the fuse keeps blowing out. Do you still have AC?
Yes mate, my ac is totally working fine...
Where can i purchase these, can you send a link
kindly enlighten me on the automatic mode actuator swap. TY
Actually right now the 2 actuators are not yet installed... Still looking for the motors... But for the intake/cycle motor is ok...
@@du3dsp I've heard it's a direct swap from the bicycle brake line original but after I squeeze my fat american ass down in there and I'm looking at it upside down, I just cant visualize how it goes on..
How did you control the AC manual controller to the new automatic controller
All the sockets are plug and play except for the hazard switch... Need to do mod on the socket...
Boss saan nyo po Banda tinabas air vent?
About 1 inch from the end...
what i need to change manuel ac to auto .. plz som details
❤❤❤🎉🎉🎉
Great video! How did you convert the manual temperature cord cable to electrical knob? Between the two air vents there is a manual arm switch that allow you to choose if the air is going to the windshield or to the front air vent , what did you do with that arm switch?
Hi... Put another motor solenoid to move the arm to open or close the vent in the upper center i will upload another video for that mod... Thanks...
I think for this conversion , you need to change the whole climate unit as well.
So far yavent touch much... Only the harness... The climate control... Did conversion on the hazard switch...so far thats it... Most of the harness is plug and play...
sir! i just bought JDM 2din panel and an headunit. ask ko lang if walang bracket yung 2din headunit ano pede maging remedyo!
thank uu!
Fabricate na lang ng bracket...
Sir. Plug and play lang ba socket nang ac sa 1 din at 2 din?
as far as when i put the sockets plug and play sya... nagkaron lang ako ng slight modification para saresistor block... and rewiring sa hazard switch... fyi usdm yung 2 din ha... sa jdm medyo masalimuot ang conversion...
Ano po convertion na ginawa nyo s resistor block?
Ginamit ko lang po yung resistor block na kasama... Yung nilalakihan ang butas d7n sa may blower housing... Ako dun sa may circulate/intake damper side nilagay since isinara ko na yung intake side...
Sir san po pwede makabili nung adaptor nung sa hazard?
Rewiring lang po dapat may kasamang hazard switch yung mabibili mong 2 din climate control...
Nice kuyang 👍👍👍
Thank you kuyang...
Goodjob! 👍
gagana parin ba sir yung lakas ng lamig ng aircon kasi ying sa stock is manual na di kabli
On my experience gumagana naman sya... Plug and play naman yan basta USDM na 2 din...
Hi sir un po bang resistor block saan nyo po kinabit doon po ba kung saan nakalagay ung sa stock or nilipat nyo ng location? At sa hazard switch socket ano po ang rewirig na ginawa, kinakabit ko po ngayon ung sa akin
Kunan ko po picture sir... Pati rewiring ng hazzard switch...
Thank you po Sir
Meron po sa harness ng usdm climate control na green na wala po syang paglalagyan naconection
sir same problem here pwede ko po ba makuha pic ng hazard switch at resistor block
@@du3dsp sir
niceee, ask ko lang boss magkano bili nyo dun sa kinabit nyo at saan mo nabili?
Hello paps... Nabili ko kay jamcris trading sa malolos... 7500 kiha ko...
Sir paano nyo wiring ginawa mo sa hazard, na convert ko na po ung sakin, my problem now is ung hazard switch.
Sir i will take a picture nung wiring ko ng hazzard switch...
sir ano po ginamit nyo na pandikit sa aircon vent
Idol ginamitan ko lang panghinang at other plastic para dumikit... Lalagyan ko pa sya ng air duct aluminum tape...
San location nyo sir..kc yong akin nag black out sya.no power
Sa malolos bulacan sir...
Ayos Bro! 👍
Salamat kuyang...
sir pwede masilip wirring ng hazard
👍👍👍
Hello Po!, ano size ng headunit mo? Salamat :)
Good day sir.. 7inches yung head unit...
102mm x 178mm
Nice paps
Thank you...
shout out naman!
Oo naman idol...
Sir baka may diagram kayo nung wiring na ginawa niyo sa hazard
Sir hm po pa install ng 2din at loc po
Hello sir... Actually di po ako shop... Hobby lang and for tutorial purpose lang po mga videos ko... Pero sa Malolos Bulacan po lacation ko if you need any help...
Ah nice po yan sir
Boss thank you dame ko customer ng 2din hirap ipaliwanag na kelangan mag modify kung stock air duct
Yes sir... Tatabasin talaga...
@@du3dsp sir can i recommend you for installation ?
Pwede naman po sir... Location nyo po? Nasa malolos kasi ako...
Sir😁
Hello...👍☺️