Just Learning Process // 2 pieces Broken Gear MainShaft repair // Only Genius Mechanic Can Teach You
Вставка
- Опубліковано 28 лют 2024
- Just Learning Process // 2 pieces Broken Gear MainShaft repair // Only Genius Mechanic Can Teach You
#brokengearmainshaftrepair
#Onlygeniousmechanicteachyou
#justlearningprocess
#pkprocess - Авто та транспорт
А теперь.....покрасить и сдать не металлолом! Или выбросить !
Когда нет запчастей и это хорошо !!!🙂🙂🙂
It is surprising! So many efforts, so many imagination and skill! Such a brave approach! But at the end, I doubt it will work. So many mistakes! Is it a real process of reparation, or just to entertain the you tube audience....
They do seem to follow an unconventional path. Heating the material whilst turning it seems strange, is it , I don't know?
@@davidturner8689It's for annealing the hardened part of the shaft for better machining.
@@davidturner8689 In the factory, this shaft was quenched and tempered. Therefore it is very hard. In order to make it posible to turn, he heat it up to around 800-900 deg Celsius to convert martensite into austenite. While cooling, austenite transfers to ferrite/pearlite structure. Now it is possible to turn. After the mechanical treatment, that part should be heated up to 800-900 deg Celsius, quenched and tempered again. In other case it will be soft and ductile therefore it will get twisted.
The heating is not the prob.the prob.is I think that gear shaft are not properly aline or straight...that's the prob...
One wonders how long & strong is that stick welding job.
+ the tempering of all metals involved is all over the place.
🧐
How long will this geared shaft last ?
Mind you in Pakistan, they tend to greatly overload their lorries.
😳
КЛАСС!!!
Резец как кочерёжка
Сверло с добавкой ртути
Ты подожди немножко =
Сейчас мы всё замутим!!!
if it is just temporary for the urgency its quite good...
ماشاءالله تبارك الله ابداع ابداع مبدع ماشاءالله تبارك الرحمن باكستان 🇵🇰 احسن انسان 👏👏👏👏👏🫵🇵🇰🫵
Шлицы болгаркой😢 класс.
Нормально, походит еще. Потом снова принесем!
Дикий народ - дикие нравы ..
@@jurisjuris5735А Вы что сделали в своей жизни, чтобы Вами восхищаться?
Sério que alguém acredita que isso vai prestar ou que ficou bom??? Um torneiro de responsabilidade nem olhava pra um serviço desse
Xem nước ngoài thấy lợi hại giỏi thật kỹ thuật quá tốt luôn
Сильно... От души. Давно я так не ржал....
Jajajajaja
You have to discover yourself in front of these true artists, they are simply true masters of their craft, can you imagine them with some good tools in Germany?
Proper training is actually that they need. Nothing wrong with Old machine. They work just as well.
in Germany they almost have forgotten to use systems they used some 50 or 60 years ago .
The reason for this is poverty makes resourcefull
I certainly would not want somthin repaird like this
And the icing on the cake is, the super accurate ground splines, ha ha. 😂😂😂
Trabalho muito bem feito.Se temperar,pode aguentar mais do que vem,da maneira original.Abtacobe Feliz Páscoa para todos
Молодцы, - знают своё дело на отлично! Цена и качество совместимы. Хочеш лучше, покупай новый, но это не значит что новый будет лучше старого ввиду того что сталь будет соответствовать по качеству!
Кто нибудь! Наточите этому токарю резцы! И покажите таблицу обороты/подача! Без слез смотреть невозможно, на такую обработку!
Это местные технологии обработки металла.😊
это же индия или Пакистан,в общем тот регион
Es emocionante hasta las lágrimas.....
no nie wiem czy tu nie przydało by się chłodziwo do nie których prac a i obroty do wiertła tego by mogło by być mniejsze według mnie oczywiście
Хорошее решение проблемы пока запчасть заказан ,а работа не будет стоять ,молоцы!!!
Wonderful!👍
Если не хотите купить такой вал, срочно заберите у них синий маркер!😅😅😅
Это их технологическая тайна и сила.😊
great craftsman would have loved to see it tig welded and a broach tool and then some kind of heat treating
С таким биением его в металлолом только
до руzzкого війскового корита піде
В металлолом пойдут только стружка и обрезки . Из этого металлолома сделают чудесный сплав, отольют заготовки и сбацают новый "вал-шестерню"! Полный пиздец!
Самое интересное этот металлолом тебя переживёт.
Beautiful 👍👍👍
СУПЕРХАЛТУРА , навіть для мене, не машинобудівника!
При сварке произошел изгиб. Хорошо видно биение шестерни. Я уже не говорю о др. косяках. Деталь нельзя ставить даже временно, т.к. это чревато поломками сопряженных деталей!
Мастер класс 👍
Снято отлично.звук есть.трудолюбие народа огромное.все вручную без станков с ЧПУ.сделайте еще перевод на Русский язык.и будет❤
Кто нибудь !!!! Объясните этому горе сварщику .что эти электроды даже близко не подходят для сварки подобных деталей. Корень заложил дерьмовой.ua-cam.com/video/4f83vDA9vUA/v-deo.html
Молодец. 100% верно.
Отломили цельнометаллический хвостовик.
Что же будет с такого рода сваркой?..
Exelente trabajo buen operador de machin shop una gran ayuda para los mecanicos y camioneros
Son indespensables
Без синей изолента не взлетит.😂 После такой сварки это долго не продержится.😅
I don’t agree with joining parts that are major, torque or stress in most cases, but this is the best joining I’ve ever seen. also I’m not a pro in any stretch but I’ve seen people just weld pieces together that have been previously welded and you can see that that’s happened and I’m thinking to myself. This is just work in this case though Primo work.
在巴基斯坦一切皆可焊😂
Good job sir ji nice video
Thanks 😊
Sangat profesional
Хороший якорь получился.
Ага, грузило на оочень большой поплавок ))
И я это безумие досмотрел до конца? Такой халтуры еще не видел😢 особенно как он нарезал зубья это просто экстаз какой-то😂
Шедевр! И следует понять, что уровень "развития" всей этой публики соответствует их "труду"!
😂😂😂
Show de bola maravilha
Spitzenklasse !!!
정말 기술 실력이 대단하네요!
The wobble of the piece is visible with naked eye. What are they doing there? Are they for real?
They are the reason things keep braking...
Very nice good job
you're a bad person
Nice bro good work
I guarantee it works better than new
Main Shaft
Поставят разбитый подшипник компенсирующий ужасное биение и поедут. Хватит на месяц а может и на час.Жесть😂 Про такой ремонт мне рассказывал отец , но это было в послевоенные годы
Parabéns excelente trabalho
Muito bom !
GREAT WORK
Très bon travail continuez comme ça 👍
très mauvais travail oui, l'arbre ne tourne pas rond du tout. c'est juste une blague cette réparation, si ça se monte ça ne tournera pas bien longtemps (si ça peu faire un tour complet 🤣
Travailler dans ces conditions avec les moyens qu'ils ont c'est déjà pas mal pour un pays sous développé et pourtant on essaye de dépanner les gens n'est-ce pas🙃
@@ahmedlg7786ce n'est pas un problème de moyen mais bien de méthode, il y a une bonne et une mauvaise façon de faire les choses. avec le même matos on peut faire bien mieux en utilisant une méthode plus logique 🧐
Wow, I am very very impress with your skill. But I like to know what happen?
The customer threw it in the trash after they had a hard laugh.
Amazing
Excelente trabalho
Here the turning work is mainly welding; a new one would probably cost more expensively. Make a pin with a diameter of 30 mm and insert it into the center of the shaft.
Я уверен эта работа выполнена в два этапа!После сбора детали и первичной прихватки сваркой обязательно нужно померять эту деталь в на месте в коробке передач!
Love from Jaranwala
Right on the money; only a 1/4 inch off.
I really respect the creativity and dedication that is required to carry out this complicated task and cannot underestimate the potential impact this form of repairing has on the overall performance no matter the severity of criticism by unknown individuals 😊😊😊
Show de bola ⚽ 👌👌👌👊🤝👏🇧🇷
That is a mess and won't last
Сначала думал куда так много оборотов. А потом услышал что видео ускорено)))
Я все понимаю но биение аж глазом видно
That was wobbling so bad. Why didn't he chuck it with an indicator? Also with all that effort to cut threads, the grinder pissed me off. You can make an indexing tool with a grinder attachment if you really don't have a horizontal mill.
The Minion voice just kills me
A co tvrdost a pevnost materialu, kolko to vydrzi v realnej prevadzke ???
👍👍👍 Good
عمل رائع
25:15 масса через подшипники! - все ок!
аааааа!!!!111
I love the skilled repair!
Parçaları taktıktan sonra tekrar ölçseniz iyi olurdu
Работает на сухую даже эмульсией не пользуется
"Amar all fixed that shaft? "
"Yes boss, fixed already."
"How so fast? Expensive part."
"Oh, machine shop fix, so cheap. He do good I watched."
"Yea? Same length?
"Yes BOSS he measured."
"Same strength?"
"Yes boss, same diameter. I watch."
"Same strength I ask, not diameter."
"I think so, what could be wrong?"
Scary when you don't understand strength of materials and metallurgy. Imagine the face of the driver when, in a panic, he needs all that structural integrity.
Original heat treatment lost. Insert unknown material. Welding rod unknown material,. Hand-made spline ends full of potential stress raisers. No new hardening and tempering. Shaft wobble/bent. Running weld current through lathe bearings. Won't be long before it fails again. Not a genius, more like a butcher.
just has to last till after the auction
These videos are just for UA-cam views and clicks. Just enjoy it for what it is 😂
You're absolutely right about that, but you can't deny it's a real "CRAK"!
Мне вал сцепления сварили на Т 170 и работал нормально
Круто!!!!
Why all this new Shaft is not available
Buonasera ho visto il video della riparazione volevo sapere perché la foratura viene fatta a secco e non raffreddata grazie mille per favore rispondete
Руки из плеч !!!
Такой вал просто так не сломать. Наверное загрузили в 10 раз больше положенной нормы
Почему работете без масла?
Ok that's good. Ferpect!
На глаз видны биения
Life time guarantee
thanks for sharing brtoher
Material added, material removed, wouldn't it need to be re-balanced?
Yikes! Not a dial indicator to be seen - but plenty of wobble. I wouldn't want to be anywhere near the equipment that is going back in.
How do you break a 1 1/2 inputshaft?
Fatigue failure. Probably caused buy over loaded vehicle.
Those are fusers! I wouldn't even get my bike repaired with that. They are not interested in any heat treatment, throwing accuracy, nothing! It's terrible to just look at it and not use it after their "rescue"!!
No cutting oil? No wonder the drill bits wobble.
절삭유 안뿌리고 하면 공구 다망가질텐데
These things break because they put too much weight on the vehicle. If they were to follow a manufacturers recommendation it wouldn’t happen. I use to do these types of repairs. They do not last. This was a solid piece of metal, a thread and welding will not replace the original composition. Sorry but this is just another half repair. And I know I have done it and seen what happens after. The driver will overload the vehicle again, and the same result follows.
Ахахахх, если это такой троллинг ради контента, ок.
Походит немного
Конечно это не ремонтопригодно все понимают это. Но деталей замены нет. То что он сделал надо сдать в металолом. Но если бы он сделал внутренние шлицы плюс посадка на горячую а так же закалку и после отпуск нормализацию. Это бы было более надежно чем забивание молотком и обваривание.
Coincido plenamente...
Станок нужно калибровать, вал получился кривой видно когда вращается. Думаю что у авто будет вибрация.
Wow san all
Ну а чё, не битый не крашеный. :)
Немецкое качество и точность
Hahaha comedy work
Артель " Напрасный труд".
If.four.cylender.crank.brocken.from.middle.can.be.welding
❤👍👍👍👍
It doesn't look reliable. Thermal tempering of the metal after welding was not done; the central part was not hardened. Most likely this part burst very quickly after installation
Интересно, чем эта страна торгует?