I personally just did the swap in my driveway mostly by myself (because my old man was against me doing the swap because of having to cut into the tunnel). My old man actually helped a little when i was stumped, but i skipped a good bit of these steps (with the knowledge my old man gave me) but the biggest one was not having to cut the tunnel. The transmission went right up and in with no problem and the car is now back on the road.
Yup, the tunnel hump is completely unnecessary unless you are switching to an aftermarket shifter, I have a hurst and felt like doing it simply because it looks nicer
I have a 302 and I’ve done everything fine but I can’t get the t5 pushed in the last 1/2 inch. Is there something that I did wrong that would effect this or is the shaft of the t5 to long for my 302? This is my first time doing something like this so any help would be appreciated.
What year car is the T5 out of and what bellhousing are you using? Judging by the comment, sounds like you have a SN95 T5 and a Fox bellhousing. The input shaft in a SN95 T5 is longer than the input shaft in a Fox T5. -Landan
No, the cluster doesn't have to be installed to start the car. If you do this, the alternator won't charge as that circuit is tied into the volt gauge on the cluster. This could also be the reason why the airbag module is beeping. It's been a while since I've looked at the circuit, but I'm pretty sure the Airbag Diagnostic Module is tied into the airbag light on the cluster. As far as the car not starting, something in the wiring isn't right. Go over it again and make sure it's all correct. -Landan
@@LegendDEJ I like doing things the correct way so, yes I used a manual transmission harness. Using the correct part to do the swap makes things alot easier I used as many factory ford parts as I could unless I found a aftermarket upgrade parts. I hope this helps.
I was under the impression you need to rebalance the rotating assembly when you swap from flex plate to flywheel? Is this the same for a 5.8 sbf Windsor
Currently doing this could you clarify the wiring at the transmission. I saw a video somewhere else stating o2 harnesses need to be repinned. You dont mention any that. Could you just clarify
We don't mention any of that because we left the automatic ECU in place. If you're replacing the factory automatic ECU with one from a manual car, then you have to match the o2 harness with the computer that you're using. This can be done by repinning the existing connector or just purchase a new harness. What year is the car you're swapping and what ECU do you have? -Landan
Hey Dallan, here is the link for the safety switch on our site and the full video breakdown: lmr.com/item/LRS-11156A/86-93-Mustang-Clutch-Pedal-Safety-Switch - ua-cam.com/video/-ej8-W6H_Cw/v-deo.html
This will depend on the mechanical skill and the condition of the vehicle. With these vehicles being 30+ years old, there may be obstacles found that we did not run into. We recommend getting with your local shop to discuss an estimate based on your vehicle.
I'm not well versed in 4-cylinder AOD to T5 conversions. The 4-cylinder cars had some oddball one-off stuff. "Most" of the swap components will work with the 4-cylinder cars. Sorry I'm not much help, but there isn't much info on this swap that's specific to a 4-cylinder. How far along with the swap are you currently? -Landan
When you get it all done you have a T5 which works for a 4 cylinder or maybe a V6 but behind a V8 it won't last very long. You spent all that time and money and end up with pretty much nothing. That's not a good trans to use for V8 motors.
@macnation3006 I'm pretty much retired now but we used to rebuild lots of T-5. V-8 motors eat them for breakfast. They work great if you don't drive aggressively. We added onto our guarantee that we don't warranty broken gears, broken or bent mainshafts, or broken cases. If you break it in half we let you keep both pieces. That's our famous 50-50 guarantee. Bent mainshaft is a common problem. They jump out of 1st gear when you accelerate. Good box but then won't handle lots of power.
After watching your video I'd bet money you've never worked one day of your life as a real mechanic. Way too many mistakes. I know you're really proud of your video but it's actually embarrassing.
The routing of the clutch cable was explained starting at 28:54. The wiring related to the swap is discussed throughout the video. What is your specific question? We'll be happy to help. -Landan
I personally just did the swap in my driveway mostly by myself (because my old man was against me doing the swap because of having to cut into the tunnel). My old man actually helped a little when i was stumped, but i skipped a good bit of these steps (with the knowledge my old man gave me) but the biggest one was not having to cut the tunnel. The transmission went right up and in with no problem and the car is now back on the road.
Good info thanks
So you didn’t cut your transmission hump?
Yup, the tunnel hump is completely unnecessary unless you are switching to an aftermarket shifter, I have a hurst and felt like doing it simply because it looks nicer
@@that1993mustang shit i got a hurtst in mine and i have no issues of fitment even without cutting the floor pans but glad someone else agrees
50Tussin taught me everything I need to know about a T5
I have a 302 and I’ve done everything fine but I can’t get the t5 pushed in the last 1/2 inch. Is there something that I did wrong that would effect this or is the shaft of the t5 to long for my 302? This is my first time doing something like this so any help would be appreciated.
What year car is the T5 out of and what bellhousing are you using? Judging by the comment, sounds like you have a SN95 T5 and a Fox bellhousing. The input shaft in a SN95 T5 is longer than the input shaft in a Fox T5. -Landan
Hey! I’m currently in the process of doing this swap to a ‘93 Fox with a 4cyl. Is everything the same as this video?
Other than some of the mechanical differences from V8 to 4-cylinder, yes, the steps are the same. -Landan
Do I need to install the manual trans harness (LRS-8793MTH)? Also is the neutral switch only necessary for the automatic?
LRS-8793MTH makes it easy. It only works for 87-93 cars, though. Are you asking about the neutral sensing switch or the neutral safety switch? -Landan
Do o have to install the cluster to start the car? It won’t start. Also what I think is the airbag warning is beeping. 5x then stops.
No, the cluster doesn't have to be installed to start the car. If you do this, the alternator won't charge as that circuit is tied into the volt gauge on the cluster. This could also be the reason why the airbag module is beeping. It's been a while since I've looked at the circuit, but I'm pretty sure the Airbag Diagnostic Module is tied into the airbag light on the cluster.
As far as the car not starting, something in the wiring isn't right. Go over it again and make sure it's all correct. -Landan
Try doing that swap in a drive way on your back. Not fun.
Been there done that! Having a lift always helps, but as with most of us, jacks and jack stands are a normal part of modding our cars.
See that’s where I’m at
did you need a manual tranny harness?
@@LegendDEJ I like doing things the correct way so, yes I used a manual transmission harness. Using the correct part to do the swap makes things alot easier I used as many factory ford parts as I could unless I found a aftermarket upgrade parts. I hope this helps.
@@TheCobraClone58 do you have a link for it or did you get it from a donor etc?
I was under the impression you need to rebalance the rotating assembly when you swap from flex plate to flywheel? Is this the same for a 5.8 sbf Windsor
No. As long as the flex plate balance weight matches the flywheel that was removed or what the engine was balanced for. -Landan
Currently doing this could you clarify the wiring at the transmission. I saw a video somewhere else stating o2 harnesses need to be repinned. You dont mention any that. Could you just clarify
We don't mention any of that because we left the automatic ECU in place. If you're replacing the factory automatic ECU with one from a manual car, then you have to match the o2 harness with the computer that you're using. This can be done by repinning the existing connector or just purchase a new harness. What year is the car you're swapping and what ECU do you have? -Landan
@latemodelrestoration mines is an 89 gt stock 5.0 with aod. Not sure what ecm i will check here in a bit. I plan on keeping the stock ecm.
Where are the neutral safety jumpers at? My 86 doesn't have them handy and I don't know where to look to see if there is any from factory.
Hey Dallan, here is the link for the safety switch on our site and the full video breakdown: lmr.com/item/LRS-11156A/86-93-Mustang-Clutch-Pedal-Safety-Switch - ua-cam.com/video/-ej8-W6H_Cw/v-deo.html
What's a rough time estimate for this swap? May have local shop do it and trying to gauge cost by hours involved. Thx.
This will depend on the mechanical skill and the condition of the vehicle. With these vehicles being 30+ years old, there may be obstacles found that we did not run into. We recommend getting with your local shop to discuss an estimate based on your vehicle.
I have a 1993 5.0 coupe and I WANT TO PUT THE TRANNY FROM A GT HATCH 1988 DOES IT FIT ?
Yes.
Will the kit work on my 93 2.3?
I'm not well versed in 4-cylinder AOD to T5 conversions. The 4-cylinder cars had some oddball one-off stuff. "Most" of the swap components will work with the 4-cylinder cars. Sorry I'm not much help, but there isn't much info on this swap that's specific to a 4-cylinder. How far along with the swap are you currently? -Landan
@@latemodelrestoration thank you for replying,I just got the transmission so far and wanted to know what parts I can and can’t use.
@@GavinGutierrez-t1z What year car and what engine did the T5 come from? -Landan
@@latemodelrestoration it is a rebuild that came out of a 1990 foxbody 2.3
@@latemodelrestoration is there any 5.0 specific parts in the kit
Cat currently wont turn over
To better assist you, please reach out via email. Thanks! -Landan
lmr.com/contact
When you get it all done you have a T5 which works for a 4 cylinder or maybe a V6 but behind a V8 it won't last very long. You spent all that time and money and end up with pretty much nothing. That's not a good trans to use for V8 motors.
What are u talking about, the t5 has been used for years with v8s
@macnation3006 I'm pretty much retired now but we used to rebuild lots of T-5. V-8 motors eat them for breakfast. They work great if you don't drive aggressively. We added onto our guarantee that we don't warranty broken gears, broken or bent mainshafts, or broken cases. If you break it in half we let you keep both pieces. That's our famous 50-50 guarantee. Bent mainshaft is a common problem. They jump out of 1st gear when you accelerate. Good box but then won't handle lots of power.
After watching your video I'd bet money you've never worked one day of your life as a real mechanic. Way too many mistakes. I know you're really proud of your video but it's actually embarrassing.
Could’ve been a great video if they took the extra 5 seconds to explain how to route the clutch cable and the new wiring 🤦🏼♂️
The routing of the clutch cable was explained starting at 28:54. The wiring related to the swap is discussed throughout the video. What is your specific question? We'll be happy to help. -Landan
@@latemodelrestoration i figured it out, but just a little bit of a better video would’ve helped a ton. Hard to see where it goes that’s all
This video could of been so much better with little adjustments.