⛐ Check out our Garage to see what tools we use and recommend: www.amazon.com/shop/worldmechanics ⛐ Subscribe and hit the notification bell by the subscribe button for new videos: ua-cam.com/channels/k_lcDzEWLs5fVRYceK3-9Q.html ⛐ Our GoFundme Page: www.gofundme.com/auto-repair-guys
Yo...thank you, thank you, thank you...my car had been sitting for months trying to figure out this problem...I was about to send in my TCM module for repair...looked this up...had a spare 30 fuse In my glove box...fixed the problem... thanks for this...you guys are the best!!!!...saved me 300 bucks!!!
Thank you! You saved me. I Knew it wasn't complicated and I found your video and found the fue. It was burned. Now I can use my car again! Thanks a LOT!
You are my hero, i was on the way to work when the fuse blew and car went into limp mode pulled over at a gas station and changed the fuse but i’m still in limp mode, any advice??
Thanks for the good video's. My E46 went into limp mode, my Trans Fuse was bad, I put in another one and it burned up right away? What would cause this to happen??? Anyone?
My bmw E 46 have been showing the gearbox warning light since I was having an a automatic transmission ,now I have converted to manual transmission.now how can I reset or remove the gearbox warning light?
Anyone know what the p0600 and the P1145 codes are for? Car is a 2000 BMW 323i. BMW forums is a joke as no one knows anything there. And I can't find anything about these codes for this car. Thank you~
A fuse kept popping in the little cluster of fuses. So I looked up online what they all talk to. Checked all the wiring. And sure enough. Wires that went to the o2 sensor on the passenger side were all melted together. Rewired that and no more CEL.
I am wondering the same thing....did you ever figure out what was making the fuse keep blowing? I am lost at the point. And am about to take the big jump and switch the mechatronics board out inside of the transmission and see if it blows the fuse again, still......have you figured out what was going on. If so what did you do to fix the issue
Hey guys great job, so this is the problem that I have on my 2002 bmw 325i, it went into "limp" mode and I did all sensor on the transmission exept the speed sensor and still the same, but I just discover thanks to you that the fuse for the dsc is blown and I change it and limp mode dessappear for maybe 10 seconds, and it keeps blowing, is it possible that I have a short on a cable?, please help, thanks, keep the great job
Angel Rosario was your traction control on while you are onnlimp mode? My 323i was just driving fime one morning. Parked it and 6hrs later instarted the car and my traction control light was on and along with the gear and the ! In it.. now only running on 4th gear. Where is the dsc fuse located? please help
@@tengzturiagaiii3185 Yes it was on while I was driving and I couldn't turn it off, but here's the video that shows where is the fuse ua-cam.com/video/YbUFPXXO-r8/v-deo.html I hope this help
@@garrett8412 well this was 3 years ago and I have a 335 now but I’m currently going to school for a Bmw tech pretty soon I’ll make videos and diys on on UA-cam also to help
Hi.. i need your help.. my car have some issue. Bmw e46 1.9. My gear is not shift then i drive my car and some times the gear shift very hard until we can hear the gear changing..
My TCM makes a constant buzz when the car is turned off, like it’s not going to sleep, but once unplugged the buzz stops. And my new battery drained after only 4 days, could this be the cause?
When I put my E46 in drive or reverse it does not move on its own power unless I give it a bit of gas and then there is a clunck in the rear and no it's not my diff bushing or subframe so what could this be?
I am wondering the same thing....did you ever figure out what was making the fuse keep blowing? I am lost at the point. And am about to take the big jump and switch the mechatronics board out inside of the transmission and see if it blows the fuse again, still......have you figured out what was going on. If so what did you do to fix the issue.
⛐ Check out our Garage to see what tools we use and recommend:
www.amazon.com/shop/worldmechanics
⛐ Subscribe and hit the notification bell by the subscribe button for new videos:
ua-cam.com/channels/k_lcDzEWLs5fVRYceK3-9Q.html
⛐ Our GoFundme Page: www.gofundme.com/auto-repair-guys
Can u do video on transmission limp mode? Thanks
a mi se me quema el mismo fusible al poner en contacto, antes de arranacar
Is there a similar fuse / fix for the petrol engine
@@cristian811lo solucionaste? ayuda tengo el mismo problema
Yo...thank you, thank you, thank you...my car had been sitting for months trying to figure out this problem...I was about to send in my TCM module for repair...looked this up...had a spare 30 fuse In my glove box...fixed the problem... thanks for this...you guys are the best!!!!...saved me 300 bucks!!!
Thank you! You saved me. I Knew it wasn't complicated and I found your video and found the fue. It was burned. Now I can use my car again! Thanks a LOT!
Hi, i know this post is over a year old but I was just wondering if you could tell me what symptoms your car was having? Thank you.
I watch you videos all the time to learn about bmws they are my passion and I hope to one day be experienced enough to be a professional mechanic
You are my hero, i was on the way to work when the fuse blew and car went into limp mode pulled over at a gas station and changed the fuse but i’m still in limp mode, any advice??
something is causing that fuse to blow over and over figure out which wire is causing it to blow
Thanks for the good video's. My E46 went into limp mode, my Trans Fuse was bad, I put in another one and it burned up right away? What would cause this to happen??? Anyone?
Check your o2 sensors that are under car on the muffler see if the wires are not on the muffler or burnt.
@@anastasiaschannel980 yes it was a burned o2 sensor wire
@@anastasiaschannel980 mine was not burnt, what other stuff can it be?
I have a P1732 and P0734 code showing up after I ran over a big rock on freeway car is constantly going in limp mode after that
Found the fuse, was blown. Replaced and now have communication with dme and egs
My bmw E 46 have been showing the gearbox warning light since I was having an a automatic transmission ,now I have converted to manual transmission.now how can I reset or remove the gearbox warning light?
One question where can I put the computer to check a code, thanks
I put my car in drive it doesn’t move unless I press the gas when I hit reverse it goes like nothing
Does this help to diagnose P1770 Code?
Is it the same on a 550i
Anyone know what the p0600 and the P1145 codes are for? Car is a 2000 BMW 323i.
BMW forums is a joke as no one knows anything there. And I can't find anything about these codes for this car.
Thank you~
Having same issur same codes ever figure it out??
A fuse kept popping in the little cluster of fuses. So I looked up online what they all talk to. Checked all the wiring. And sure enough. Wires that went to the o2 sensor on the passenger side were all melted together. Rewired that and no more CEL.
That's crazy I had the same exact problem it's fixed now that is a million
Any input on a code p0709?
Hey I have a 2001 bmw 325ci my fuse keep burning after I change it
I am wondering the same thing....did you ever figure out what was making the fuse keep blowing? I am lost at the point. And am about to take the big jump and switch the mechatronics board out inside of the transmission and see if it blows the fuse again, still......have you figured out what was going on. If so what did you do to fix the issue
Great video but can u do a video. Or comment on the dip stick can I add fuild in it like any other car
Hey guys great job, so this is the problem that I have on my 2002 bmw 325i, it went into "limp" mode and I did all sensor on the transmission exept the speed sensor and still the same, but I just discover thanks to you that the fuse for the dsc is blown and I change it and limp mode dessappear for maybe 10 seconds, and it keeps blowing, is it possible that I have a short on a cable?, please help, thanks, keep the great job
Angel Rosario was your traction control on while you are onnlimp mode? My 323i was just driving fime one morning. Parked it and 6hrs later instarted the car and my traction control light was on and along with the gear and the ! In it.. now only running on 4th gear. Where is the dsc fuse located? please help
@@tengzturiagaiii3185
Yes it was on while I was driving and I couldn't turn it off, but here's the video that shows where is the fuse
ua-cam.com/video/YbUFPXXO-r8/v-deo.html
I hope this help
Thank you
yo tengo el mismo problema, cambiando el fusible al ponerlo en contacto lo vuelve a quemar
Angel Rosario yes mine keeps blowing too. The the small black box that has like 5fuses right? One 30amp kept blowing. Not sure why
I also have a bmw e46 and I have codes p0700 and p1892 i was wondering if you could help me
same! Any idea what it was?
@@garrett8412 well this was 3 years ago and I have a 335 now but I’m currently going to school for a Bmw tech pretty soon I’ll make videos and diys on on UA-cam also to help
Hi.. i need your help.. my car have some issue. Bmw e46 1.9. My gear is not shift then i drive my car and some times the gear shift very hard until we can hear the gear changing..
I have a problem in BMW 2.5i 2005 hear indicat light is not coming in the dashboard please can you help me to fixed it out
My. E46 wasn't showing any warning lights on the dash, it just went in limp mode..can the fuse be the cause???
Any fix?
My TCM makes a constant buzz when the car is turned off, like it’s not going to sleep, but once unplugged the buzz stops. And my new battery drained after only 4 days, could this be the cause?
What will happen if you change the gierbox and not reset
what makes a cer not to rave beyond 2000rpm
Tranmission light stays on and goes off when I change the fuse but pops immediately anyone can tell me why it does that?
I have 330i e46 I literally cant reverse at all but I can put it on drive and itll drive smooth
8TY1 Productions check the code must be a sensor. That’s what happened to mine
Did you find out what it was ? Got a 335i e93 same drives fine in drive but very very sluggish in reverse and doesnt hold it
@@BillyTheSKID just had to get a whole new trans
@@prodbresc1027 did you try and even flush it or replace gear selector valve?
@@BillyTheSKID I took it to the bmw specialist and told me I need a new trans
Need help with transmission light
When I put my E46 in drive or reverse it does not move on its own power unless I give it a bit of gas and then there is a clunck in the rear and no it's not my diff bushing or subframe so what could this be?
Hi
My bmw 530d years 2005 code error ced 418.?
What would cause the transmission to down shift hard and shift hard when cold
What if mine keeps blowing the fuse
I am wondering the same thing....did you ever figure out what was making the fuse keep blowing? I am lost at the point. And am about to take the big jump and switch the mechatronics board out inside of the transmission and see if it blows the fuse again, still......have you figured out what was going on. If so what did you do to fix the issue.
@@myob3did you find the solution? I have the same problem keps blowing the same fuse