I’m having this exact issue on my 2005 Frontier. Will a bad TCM give a different code than a bad valve body? My OD light isn’t on bud OD is not working or low gear. It’s like I’m taking off in 2nd or 3rd gear 🤷🏼♂️
just want to check,is the input turbine sensor is part of the selonoid pack my 07 pathfinder keeps setting a code for that P0715 thank you for any input
My 2006 pathfinder jerks when R is selected and also the transmission gives a P0744 and P1759 code do you think changing the valve body will work or no? Also a jerk when OD is engaged and disengaged.
Hey love your videos. I have a question I have a 2014 Nissan frontier 4.0L 6 cylinder. The engine check engine light came on and ran the code P0720 so I changed out the output speed sensor. Still giving me the code and check engine light still on. What would you recommend I do. Thank you for all you do
Hello. I recently got pathfinder 4.0 2010. when i shift from R n D there is a slight delay. about 2-3 seconds. Only when from R to D. Is this normal? this may be a common problem with this car? new fluid and everything else works fine. thanks for the info
If the solenoid is bad, can I replace just that on the valve body? Or do I need to replace the whole thing? Also notice some place say "pre-flashed, no dealer flash required with vin #" how true is that? Great vidoe btw thanks
Got a 2005 Titan 2wd. Mines is sluggish taking off feels like it’s taking off in 2nd gear just for a few seconds when it gets going all gears shifts fine
My frontier truck jerks violently when you put in drive and reverse. it also jerks when slowing down at the light and jerks from 1st to 3rd. Do you think I should change the valve body?
guess who's changing out a valve body out today ? thanks for the video
no way. those are always fun. hope everything goes well. good to hear from you bud
You let us hear you talking but then when you took it apart which is the most important part you fast forwarded it and no direction.
I’m having this exact issue on my 2005 Frontier. Will a bad TCM give a different code than a bad valve body? My OD light isn’t on bud OD is not working or low gear. It’s like I’m taking off in 2nd or 3rd gear 🤷🏼♂️
just want to check,is the input turbine sensor is part of the selonoid pack my 07 pathfinder keeps setting a code for that P0715 thank you for any input
Hello sir, I have a 2006 Nissan Xterra same vehicle where’s the output speed sensor on the transmission please
My 2006 pathfinder jerks when R is selected and also the transmission gives a P0744 and P1759 code do you think changing the valve body will work or no? Also a jerk when OD is engaged and disengaged.
Hi there, i have same issues with my xterra. Just want to know the part number of the body valve thanks.
Ow much do you chage i need to pix mine also thanks
Hey love your videos. I have a question I have a 2014 Nissan frontier 4.0L 6 cylinder. The engine check engine light came on and ran the code P0720 so I changed out the output speed sensor. Still giving me the code and check engine light still on. What would you recommend I do. Thank you for all you do
Check to see if the signal is reaching the module. Could be a bad module
@gautorepair will do thank you
Where did the owner get the tcm from? Where are you located in South Florida?
Would you be able to change the output speed sensor through there or easier to go through the drive shaft side
Hello. I recently got pathfinder 4.0 2010.
when i shift from R n D there is a slight delay. about 2-3 seconds. Only when from R to D. Is this normal? this may be a common problem with this car? new fluid and everything else works fine.
thanks for the info
What’s the torque of the bolts that hold the transmission module? What’s the torque to screw the outer cover back on? Thanks for this video.
Not sure about the torque for the pan but the valve body bolts are torqued @ 70 in/lbs
If the solenoid is bad, can I replace just that on the valve body? Or do I need to replace the whole thing? Also notice some place say "pre-flashed, no dealer flash required with vin #" how true is that? Great vidoe btw thanks
Im not sure if they sell just the solenoid. But if it comes pre programmed then its plug and play
Got a 2005 Titan 2wd. Mines is sluggish taking off feels like it’s taking off in 2nd gear just for a few seconds when it gets going all gears shifts fine
I changed the tcm but im getting a u1000 code and no gear indicator does it need to be reprogram
Yes. Programming is required
Nissan dealership said that there's no available programming for the tcm I bought online
My frontier truck jerks violently when you put in drive and reverse. it also jerks when slowing down at the light and jerks from 1st to 3rd. Do you think I should change the valve body?
Have you scanned for codes
@@gautorepair Yes they said I should change throttle body change the throttle body. Nothing changed
The throttle body or the valve body? Two different parts
@@gautorepair throttle body is what I changed and it was still jerking
With out knowing the codes or anything it would be difficult give you a direction
Is the vehicle speed sensor reachable after the valve body is removed?
One is on the valve body the other is in the bell housing
I have the same problem on my Titan, solenoid is bad so I need to replace the valve body. I’m from south Florida can you send the contact ?
Gautomotive2004@gmail.com
En que estado te encuentras ??
Florida
I'd like to see it slowed down in the middle and hear what your saying!
Where did you get your valve body from?
Nissan dealer
What was the cost of the valve body?
The valve body itself is over 1k
❤❤❤
Brother where are you located?
South Florida
Not good