Volvo Penta 290 Dp-A Dp-B outdrive Sterndrive Removal

Short Video less than 8 minutes showing DIY Volvo Penta 290 Dp-A Dp-B outdrive Sterndrive Removal Visit FreshWaterVolvoPentaParts.Com for thousands of hard to find and obsolete Swedish Volvo Petna Parts

[@Bobssecondhand]

Well done Ryan! This helped alot. All the best from Sweden =)

[@javierzerozeroseven9959]

WOW In less than 10 minutes.

[@pfcpatsy]

Great video and explanation. Exactly what I needed. Thanks guy. 👍

[@josehechavarria2003]

Thanks for your video

[@aquaholictherapy463]

Thanks for the straightforward video!!

[@mikaeljansson280]

thanks👍 you have done this before I notice

[@MrLinezzz]

such a great video. without it, it would have been impossible for me to get that thing off 💪

[@travisconner1581]

Never comes apart that easy 😂

[@stefcampagna2321]

Awesome video. Thks !

[@lorenmaly1637]

Badass! Thank you!

[@mikeshanaberger7503]

Thank you!

[@dominickentrekin598]

I am replacing the Bellows and gimbal bearing on this exact stern drive. My problem is how do you remove the shaft after the drive comes off? Great video by the way!

[@Off2Fly737]

Great video! Exactly what I needed to see.

[@terryjackybishop8995]

I need to have my drive rebuilt

[@ryanvanlandschootd.c.671]

Any advice for removing the shift cable connector ( little metal piece at the end of the threaded rod)? Mine will not break loose even with vice grips holding the threaded rod.

[@goproexplo9290]

Nice Video. I need some help, i got the leg off 100%, when i took the pin out for the trim rams, one ram compressed and the other lengthened. I felt to see if i could push and pull and they seem solid, Why has this happened? How do i get them free to move to line them up? Thanks

[@randallweichbrodt1582]

Thanks Ryan!

[@1stinsonguy]

Ryan, do you have a photo of an installed fuel pump on a AQ205A engine? Thanks.

[@georgebernero4634]

How did you remove the trim cylinders

[@mvperseverance]

I've got that same drive, but my water intake hose is really pinched. Where it connects to the drive itself, it comes off that point and goes starboard before it bends back to the port side where it goes through the transom. Seems like a silly design, or I got the wrong hose. Any suggestions?

[@joneich1591]

That extension really made my life a lot easier.. 😜😅😅😅😂😂😂👍

[@dylanholzenkamp1745]

Have any videos of doing the primary shaft?

[@hedgepethracing9590]

Good looking out on the video, I'm praying someone greased my Monday morning, Volvo drive...

[@ManuelDiaz-fm2dv]

Como puedo sacar el pasador que agarra el brazo donde coge el cable del timón

[@CorriG]

Thank yoooouuuuuu...... 😅😅😅

[@grasscutter88]

I expected it to just fall down when he pulled the main hinge pins out.

[@jeremyhale4137]

How do you put it back in!??

[@ThomasKabalt]

Dat vroeg ik mij ook al af haha

[@justingeturgun]

What happens when your hinge pins bolts are stuck lol

[@seanstewart9722]

Any progress on this? I’m running into the same issue.

[@turboed00SI]

I had to heat mine up, be careful not to go too hot though lol

[@garypeatling7927]

Ok but using gun to undoe seized bolts is silly , Seen threads torn out blow lamps and oil more sensible