Your starting to seem more relaxed in your videos your well spoken and seem to know alot of info it's good seeing n/a serouse as most people start out in them
@Taylor atkinson Thanks heaps mate, but I may have you fooled if it seems I have a lot of info! Know a little but a lot of research goes into each ep too to try back it up and not make a fool of myself 😂 And glad people are responding to the NA stuff, like you said it’s were we pretty much all start.
Got a kit from Mace for about $330 cash and then fitting including front main oil seal at Maxx performance for $200. Would recommend fitting yourself because something developed a rattle after they did the work and they made no effort to assist diagnosing the fault. Am pleased with the improved power and response. Worthwhile mod for the money.
I welded one up from some scrap metal . Dual purpose holds the harmonic so you can remove the bolt then bolt a plate with a big bolt turn and remove easy as. Cost $35 for a flat plate bearing/wheel puller to bolt on. I made it from a huge 100 mm × 10 mm thick washer from the back of my sons dead subwoofer welded three bolts with a piece of small square steel 45 mm to make hooks to go behind the three arms/spokes in the harmonic ballance I taped four bolt holes put the puller on the came off easy. Oh year I welded a bar about 400 mm it sits on or under the shasie rail to stop the harmonic ballance from turning . I use the handle to keep the timing mark lined up.
@Bigg Bhudda There's a few listings on eBay for just the balancer and one for the kit but at a bit of a premium price compared to when I got it. Not sure what the go is, may be worth checking with Mace Engineering to see if they're getting them back in to save some money. bit.ly/3344JHJ bit.ly/3jBDFWK
Anytime mate, just installed my 20% underdrive and can definitely feel a difference in response and pull. Thanks for all the tips. It's not dodgy if it works, right?! 👍😆
Good video mate, just wanted to add sumthing, you should always put sum rtv sealant on the harmonic balancer around the key to stop leaks, also, while ur swapping it out is a good time to replace the crank seal, especially if ur going to get rid of the tool. Keep up the nice work
@Justin Draper Hey Justin, awesome info thanks mate. I had intended to change the crank seal but didn't get one in time... and got lazy on this! You're right though I probably should have, and cheers for the other tip, now I know where to keep an eye out for leaks and to improve in future so big thanks mate 👍
Good to see you back mate! I think the end result will show that many incremental changes will defo add up at the track! I know you have hinted at putting a LSD in, if you do - go a ratio change as well. In my opinion, it’s the biggest single thing you can do to wake up the car (and is bum dyno approved!)
@Meatball Garage Hey Marc, thanks mate. Fingers crossed you’re right, even if not the car is feeling great for what it is. Yep will hopefully be going LSD very soon, and I did consider changing ratios while it was out but decided against it at this stage for a few reasons. The car unfortunately has to do some decent highway kms still whether I like it or not and aiming to keep this to mods that pretty well anyone can do confidently at home themselves. Sure gears would be doable too but starts pushing a little beyond beginner stuff perhaps? Working on anything to do with this diff and cradle setup is a real pain as it is! Not to mention a line had to be drawn somewhere unfortunately, the next stage for this car is already burning a hole in my pocket too!
Can definitely vouch for the underdrive kit! Installed it on my fg manual and I noticed alot better response with the throttle. AC doesn't have an issue unless it drops below idle. Not major, only fan speed drops with the rpm a little. At idle no issue and aircon still cools off plenty.
@Heath Irwin Awesome, I didn't expect there to be any issues but good to at least test cause I didn't expect to be quite as pleased with the improvements either! You never know. Cool to here some more feedback on them too, cheers mate 👍
@project Balrog Awesome, thanks for watching mate. Hope you’re enjoying the series 👍, congrats on putting up with that many of my videos in such a short time!
Hmm , did very similar mods to an atmo FG sedan a few years ago , no underdrive pulley , but extractors , cold air intake and 3.46 diff gears with lsd in a 6 speed auto and then just got a mail order engine and gearbox tune. FG's are even heavier than the BA's .....hard to believe , I know !!! Even so , I managed a 13.6 @ 99 mph. Surprised a few people , including myself :)
@Ford AU Damn good time there mate! Those 3.46 are pretty short in the FG, are they 2.73 stock? Would feel pretty quick off the line, which will be the weak point of our 4 speed I think. Hopefully we can get the mph up closer to your figures though.
@@BrowneysGarage Yup , 2.73 stock for all the 6 speed autos. Going by memory I did a 1.9 60 footer . The run is on my channel , few years back though :). Eventually turbo charged it .... as you do.
Hey Mate! Love your videos! Got an Fg g6e i wanna do this mod as well. Now its been a couple years, how has the ac been in the summer after this mod? A lot of mixed messages online but a lot saying what you said were voltage isn’t really that much of a difference. Be good to know if the ac still works fine in summer. Keep up the great videos!
Awesome, I’ve looked at these crank pulleys but was unsure about the reduce in the other pulleys. I was going to buy one and test it out just like you are but you beat me to it. Thanks mate looks like I’m getting one 😁👍👍 *also is the crank bolt reverse thread?
Hi. Great stuff with the 20% underdrive pulley kit. Tell me yourself or anyone else for that matter. Is it worth getting the Billet underdrive pulley's also put on the Power Steer/Water Pump and Alternater. And getting a bigger belt as these pulley's are larger than factory.? 🤔
6:03 idk why thats so true, ive never remembered, just done it, weird explanation but idk i can just tell if its on wrong, or going on wrong its just always been obvious to me ive never put one on wrong either, but the sticker on the hood has helped in the early days
Hey Browney, how about a 2,500 or 3,000 stall converter next? Tell your missus the old one is running out of rpm and the new higher rpm one will last much longer before it runs out again😁
Excellent video mate. Do you reckon the Underdrive pulley will accelerate engine wear since there is no rubber to dampen the engine’s vibration? I am tempted to put one on my v6
Hi mate, great stuff I am really enjoying the Barra videos. If you are looking at doing the diff, do you think you will get around to doing a converter change as well?
Hi Browney your video's fit really nicely into a needed slot mate thanks, all of us DIY BA/BF FG and Territory owners like it. I Have a BF 6 speed, an NA Territory and an FG Turbo, im looking at a King Brown cat back for the Territory and that pulley upgrade, your thoughts?
@Frank Redward Thanks mate, glad you’re enjoying them. Sounds like a nice fleet you have there. I have no experience with King Brown but I’d assume the catbacks are all much the same. I’ve been pleased with the underdrive pulley kit, the extra throttle response/feel was a nice surprise and the performance gain, particularly up top, seems worthwhile.
@@BrowneysGarage I've gone down the other way, have a 998kw rebuild kit with 4.1 truetrac on rwd and an electric motor running the front 4.1 truetrac diff 400nm. I also have a v3hb vortech that was running off the same motor but have decided to run stock power and go hybrid straight to the wheels. Sold my pump and injectors and running stock power in the motor with the same 0-100 times as running 500hp before... Just quicker off the mark. Has an extra 3phase alternator that trickle charges at idle at 144-160v and peaks 168v. Lithium ion titanium cells in the back. Can shoot the cells with a shotgun and they'll still work. Great technology. Running 168v peak can set my power levels I the front to save on petrol charging and charge off solar at home or flick a switch and have maximum power from the foot throttle if needed. Reliable is key....
Good stuff mate, I will be doing pretty much the same mods to my grandpa-spec 03 BA Futura soon, same exhaust, same headers (I am assuming yours are PH4490's), same underdrive pulleys..where mine differs is my intake, instead of that Mace Engineering CAI, I have a Typhoon airbox (with the extra intake snorkel below the left-hand headlight), K&N panel filter, and an SS Inductions BigMouth intake (Snorkel inlet is about as wide as the radiator!), going through a Territory Plenum into the stock manifold. Speaking of the stock manifold, I also just picked up an FG N/A Intake manifold today for $100 (with the FG fuel rail, injectors (not that I am going to use them) and manifold bolts) and I suggest that as your next mod to do, its a little fiddle-farty, you need to get a bolt spacer kit for the BA injectors (I think these are the appropriate ones: chiptorque.com.au/product/fuel-rail-spacer-kit/ Though I still need to ask if they work with the N/A FG manifold or only the Turbo manifold, they look right at first glance), you need to either make an adapter plate for the BA throttle body to mount to the FG manifold, or just mod the TB itself, and you need the heater piping from an FG barra 195 as well, and need to mod it with some hose to plumb up to the firewall of the BA engine bay (And also in my case, you may need to source an FG oil dipstick), I also suggest pairing it with one of these while you are at it: www.maceengineering.com.au/COLD-AIR-INTAKE-MANIFOLD-INSULATOR-To-suit-EF-BF-6-Cylinder-UPPER Lastly you will need to fab up some sort of 3" pipework to go from the back of your Mace CAI to the TB, should be a short run since the FG manifold faces the back of the air intake box...I've seen blokes claim up to 20rwkw from doing this mod (after a custom tune ofcoarse) and this sounds reasonable to me, since the first barra engines were 182kw at the crank, and the FG's were 195kw at the crank, a good tune on 98RON combined with all the other supporting mods would see in or around 200kw at the rears (That's the figure I am hoping for).
@Glyn Atkin Hey mate, thanks for watching and sharing. Correct that this is running PH4490's. As far as the FG intake they do look promising and for an 'all out' NA build it would make sense to test this out but there are more plans for this car in the future where this would have to come off anyway. I'm very keen however to hear how you go and see results once you've completed this, sounds like it's going to be a tough NA combo that would surprise a lot of people. Regarding adapting the BA throttle body to the FG manifold, are you aware there's an adapter available to suit. Perhaps you are as you seem well across it but if not check it out - facebook.com/customalloywelding/photos/a.1101063416702619/1778062345669386/?type=3&theater Best of luck mate 👍
@@BrowneysGarage I am aware of his work, I think he was asking $200 for the adaptor plate, which I'll probably end up just forking out for, out of convenience. Maybe 4.11 diff gears and an LSD should be your next mod then, since 4.11 diff gears are good for the strip, I'm personally thinking of going with 3.9's and an LSD as well as some of my other planned mods.
Just found this series. A: I wish I hadn't sold my Barra, and B: Can you buy a VZ and do a similar series lol? I already bought the underdrive kit for the VZ, seeing this made me feel like it was justified. I'm doing the timing chains, new oil pump and balancer all at once. Greast vid!
🤣 Thanks very much mate. Maybe you can take your VZ and film a similar series, wouldn't take much to improve on the quality of videos I put out mate it's all pretty basic... including the host. Hope you get decent results from the underdrives as I felt I did, seems like much more of a no brainer for yourself to do while you're in there at least 👍
Thanks so much for this vid Browney! I've been wanting this kit from MACE for ages, but I was worried about its impact on the accessories. I couldn't find any other user feedback on that issue, but you've given me the confidence to give this kit a go! Thanks mate, love your work!
@@BrowneysGarage it's been great fun, as you do the mods I buy them and follow along last week I did aftermarket trans cooler & just ordered this pack and once it aarives I'll get stuck in .
did you ever test AC out as i wish to fit this kit to a 2015 TERRITORY as i have replace the balancer 2 times now they keep coming off ( crap rubber in the balancer ) going to try this kit the cars only done 120K all i was worried about was city driving charging and cooling and the AC
@Mr. Broccoli I wouldn't write of the FG manifold, seems there could be decent gains there - maybe one day we'll give it a go (www.fordforums.com.au/showthread.php?t=11373221). And if you're talking aftermarket plenum I would hope they're better at up to $1k plus compared to a second hand FG inlet but you're right, they seem like a little bit of mucking around to make work and fit right.
Hi mate, could you please make a small video how we can find engine number location on xr6 ba 2004 , lot of people say underneath the exhaust manifold, I try to look where but I can't find nothing, thanks
Absolutely, XT and XR6 are mechanical pretty much the same except often different diff gearing. May also need a slightly different rear exhaust section because the XT doesn’t have the rear bumper cut out but should be stocked by exhaust shops still. Good luck and enjoy mate
Hey Brock, no dramas at all with this kit so far. It doesn't get driven nearly enough but other than the improved throttle response/small performance gain I wouldn't know it was in there without looking for it 👍
Hey bro, my bf falcon has recently started to flash adp pef we're the shifter symbols are eg P R D. I've replaced the transmission filter and oil and when it's been driving it does stop but still when I start the car it flashes, if u know anything to fix I'd appreciate any help. Cheers
Okay so same voltage as before Otherwise if you don’t get enough voltage your burn out your coils How has it been going since then voltage wise I’ll send my revs have dropped down a lot down to about 550 now Yeah I learnt my lesson do need the kit I need to buy the belt that specially for this balancer and the idlers
Yaaaaaaaa!!! Browney's back! That must mean his postie visited him too! A performance mod, that may be interesting to some, could be diff ratios and if they are worth it on a car like this. This was a great video. Simple but still informative. Do you think Turbo Taxi runs one of these? :P
@GlensGraphix Mr Glen you legend, good to hear from you. He sure did but unfortunately I can’t put all the blame on the fine people at AusPost! Quantity has slowed a bit here due to other factors and I really want these to be of a decent quality, as much as I can anyway. If that means less videos sometimes I hope people will understand and stick with us, and it seems they will thankfully. Awesome idea and it’s something I’d love to cover but don’t think it’s going to happen in this one just yet, the diff will be touched next though - are you reading my mind!? And poor Turbo Taxi and Scotty, the guy can’t catch a break at the moment. Thanks as always Glen 👍
@Mr. Broccoli I'm sure poor Turbo Taxi wasn't running one but don't know if they're completely not worth it, increased efficiency is good for any engine. The dyno graph shown in the video is actually from a turbo car with 7-8rwkw gain I believe, so bang for buck $40-50 / rwkw doesn't seem terrible?
Other way around as the crank pulley is smaller, this always throws me, so much so that I had to panic and go double check! Think of it this way. The smaller crank pulley has a smaller circumference and therefore for each rotation the belt is driven less distance. Anything driven off this belt (all accessories) is then spun less for each RPM of the engine. Hope that makes sense, and that my logic is correct! 👍
11:00 - It's not earth shattering but I definitely think it made some difference. At very least it felt like it improved throttle response which made it more enjoyable to drive. Didn't expect that but I would do the mod again, I was happy with it.
Your starting to seem more relaxed in your videos your well spoken and seem to know alot of info it's good seeing n/a serouse as most people start out in them
@Taylor atkinson Thanks heaps mate, but I may have you fooled if it seems I have a lot of info! Know a little but a lot of research goes into each ep too to try back it up and not make a fool of myself 😂
And glad people are responding to the NA stuff, like you said it’s were we pretty much all start.
Good to see you back legend
Got a kit from Mace for about $330 cash and then fitting including front main oil seal at Maxx performance for $200.
Would recommend fitting yourself because something developed a rattle after they did the work and they made no effort to assist diagnosing the fault.
Am pleased with the improved power and response. Worthwhile mod for the money.
WELL DONE BROWNY. NO FLUFF, STILL PROFESSIONAL. HAD A GOOD LAUGH. CHEERS 195BARRA MAN...
Thanks very much mate 👍
Incredible potential in those motors man,I'm truly impressed and I would love to drive a car over there with a souped up turbo motor in it.
I completed this mod after watching this video.. cheers
I welded one up from some scrap metal . Dual purpose holds the harmonic so you can remove the bolt then bolt a plate with a big bolt
turn and remove easy as. Cost $35
for a flat plate bearing/wheel puller
to bolt on. I made it from a huge 100 mm × 10 mm thick washer from the back of my sons dead subwoofer welded three bolts with a piece of
small square steel 45 mm to make
hooks to go behind the three arms/spokes in the harmonic ballance
I taped four bolt holes put the puller on the came off easy.
Oh year I welded a bar about 400 mm it sits on or under the shasie
rail to stop the harmonic ballance from turning . I use the handle to
keep the timing mark lined up.
Got the same I was pleasantly surprised by the results 😛
Where did you order yours from? I can't seem to find them for sale anywhere, has powerbond stopped making them?.
@Bigg Bhudda There's a few listings on eBay for just the balancer and one for the kit but at a bit of a premium price compared to when I got it. Not sure what the go is, may be worth checking with Mace Engineering to see if they're getting them back in to save some money.
bit.ly/3344JHJ
bit.ly/3jBDFWK
@@BrowneysGarage yeah ill check it out mate thamks a bunch 👍
Just bought myself a nice BA and your channel has helped so much. Looking forward to installing these soon 👍
Awesome! Enjoy the new BA and thanks for watching mate 👍
Anytime mate, just installed my 20% underdrive and can definitely feel a difference in response and pull. Thanks for all the tips.
It's not dodgy if it works, right?! 👍😆
Good video mate, just wanted to add sumthing, you should always put sum rtv sealant on the harmonic balancer around the key to stop leaks, also, while ur swapping it out is a good time to replace the crank seal, especially if ur going to get rid of the tool.
Keep up the nice work
@Justin Draper Hey Justin, awesome info thanks mate. I had intended to change the crank seal but didn't get one in time... and got lazy on this! You're right though I probably should have, and cheers for the other tip, now I know where to keep an eye out for leaks and to improve in future so big thanks mate 👍
Loving the video’s, well done young fella
@Trent Mc Swift Thanks mate, legend 👍
Good to see you back mate! I think the end result will show that many incremental changes will defo add up at the track! I know you have hinted at putting a LSD in, if you do - go a ratio change as well. In my opinion, it’s the biggest single thing you can do to wake up the car (and is bum dyno approved!)
@Meatball Garage Hey Marc, thanks mate. Fingers crossed you’re right, even if not the car is feeling great for what it is.
Yep will hopefully be going LSD very soon, and I did consider changing ratios while it was out but decided against it at this stage for a few reasons. The car unfortunately has to do some decent highway kms still whether I like it or not and aiming to keep this to mods that pretty well anyone can do confidently at home themselves. Sure gears would be doable too but starts pushing a little beyond beginner stuff perhaps? Working on anything to do with this diff and cradle setup is a real pain as it is!
Not to mention a line had to be drawn somewhere unfortunately, the next stage for this car is already burning a hole in my pocket too!
Can definitely vouch for the underdrive kit!
Installed it on my fg manual and I noticed alot better response with the throttle. AC doesn't have an issue unless it drops below idle. Not major, only fan speed drops with the rpm a little. At idle no issue and aircon still cools off plenty.
@Heath Irwin Awesome, I didn't expect there to be any issues but good to at least test cause I didn't expect to be quite as pleased with the improvements either! You never know. Cool to here some more feedback on them too, cheers mate 👍
Did the steering feel different or stay the same?
i started watching this series last night and boom new ep just as I ran out of vids to watch
@project Balrog Awesome, thanks for watching mate. Hope you’re enjoying the series 👍, congrats on putting up with that many of my videos in such a short time!
Hmm , did very similar mods to an atmo FG sedan a few years ago , no underdrive pulley , but extractors , cold air intake and 3.46 diff gears with lsd in a 6 speed auto and then just got a mail order engine and gearbox tune. FG's are even heavier than the BA's .....hard to believe , I know !!! Even so , I managed a 13.6 @ 99 mph. Surprised a few people , including myself :)
@Ford AU Damn good time there mate! Those 3.46 are pretty short in the FG, are they 2.73 stock? Would feel pretty quick off the line, which will be the weak point of our 4 speed I think. Hopefully we can get the mph up closer to your figures though.
@@BrowneysGarage Yup , 2.73 stock for all the 6 speed autos. Going by memory I did a 1.9 60 footer . The run is on my channel , few years back though :). Eventually turbo charged it .... as you do.
@Ford AU Nice, will check it out 👍
Hey Mate! Love your videos! Got an Fg g6e i wanna do this mod as well. Now its been a couple years, how has the ac been in the summer after this mod? A lot of mixed messages online but a lot saying what you said were voltage isn’t really that much of a difference. Be good to know if the ac still works fine in summer. Keep up the great videos!
Once again another great video like alway's mate
@BGAMERMAX Thanks mate, too good 👍
Nice work mate thanks for the video your a legend bro
No thank you mate, appreciate that very much 👍
Awesome, I’ve looked at these crank pulleys but was unsure about the reduce in the other pulleys. I was going to buy one and test it out just like you are but you beat me to it. Thanks mate looks like I’m getting one 😁👍👍 *also is the crank bolt reverse thread?
Nice, was pleasantly surprised with how the car felt after this one so hope you enjoy mate. And no the crank bolt is standard thread 👍
Great video Browney, well done mate
@Michael’s Projects Thanks mate 👍
Hi. Great stuff with the 20% underdrive pulley kit. Tell me yourself or anyone else for that matter. Is it worth getting the Billet underdrive pulley's also put on the Power Steer/Water Pump and Alternater. And getting a bigger belt as these pulley's are larger than factory.? 🤔
6:03 idk why thats so true, ive never remembered, just done it, weird explanation but idk i can just tell if its on wrong, or going on wrong its just always been obvious to me
ive never put one on wrong either, but the sticker on the hood has helped in the early days
ohyea its a "fkn bonnet" my bad xD
9:42 i suppose the one thing ive always remembered is that the belt has to wrap most of the way around the balancer/crank
Hey Browney, how about a 2,500 or 3,000 stall converter next? Tell your missus the old one is running out of rpm and the new higher rpm one will last much longer before it runs out again😁
@Gazwald Of Etonsville 🤣 Thanks mate, pretty likely we'll end up doing something like this but not planned just yet.
Thanks for making another great video Browney . Cheers 🍻
@Conservative Sniper Hunter Thanks for being here and watching as always mate 👍
Excellent video mate. Do you reckon the Underdrive pulley will accelerate engine wear since there is no rubber to dampen the engine’s vibration?
I am tempted to put one on my v6
Hi mate, great stuff I am really enjoying the Barra videos. If you are looking at doing the diff, do you think you will get around to doing a converter change as well?
@Darren Broadbridge Thanks heaps mate. Honestly don't think we will in this series but I wouldn't completely rule it out.
What about the 25% pulley? Did you consider it? And if so, why did you decide against it?
Hi Browney your video's fit really nicely into a needed slot mate thanks, all of us DIY BA/BF FG and Territory owners like it.
I Have a BF 6 speed, an NA Territory and an FG Turbo, im looking at a King Brown cat back for the Territory and that pulley upgrade, your thoughts?
@Frank Redward Thanks mate, glad you’re enjoying them. Sounds like a nice fleet you have there.
I have no experience with King Brown but I’d assume the catbacks are all much the same. I’ve been pleased with the underdrive pulley kit, the extra throttle response/feel was a nice surprise and the performance gain, particularly up top, seems worthwhile.
Long-term it has less dampening, id be looking at a ross dampener....
Especially if you plan on increasing the power
Hmm will have to keep this in mind, thanks mate 👍
@@BrowneysGarage I've gone down the other way, have a 998kw rebuild kit with 4.1 truetrac on rwd and an electric motor running the front 4.1 truetrac diff 400nm.
I also have a v3hb vortech that was running off the same motor but have decided to run stock power and go hybrid straight to the wheels.
Sold my pump and injectors and running stock power in the motor with the same 0-100 times as running 500hp before...
Just quicker off the mark.
Has an extra 3phase alternator that trickle charges at idle at 144-160v and peaks 168v.
Lithium ion titanium cells in the back.
Can shoot the cells with a shotgun and they'll still work. Great technology.
Running 168v peak can set my power levels I the front to save on petrol charging and charge off solar at home or flick a switch and have maximum power from the foot throttle if needed.
Reliable is key....
@@BrowneysGarage as far as I know, I'm the only hybrid barra terriitory in the world.
Good stuff mate, I will be doing pretty much the same mods to my grandpa-spec 03 BA Futura soon, same exhaust, same headers (I am assuming yours are PH4490's), same underdrive pulleys..where mine differs is my intake, instead of that Mace Engineering CAI, I have a Typhoon airbox (with the extra intake snorkel below the left-hand headlight), K&N panel filter, and an SS Inductions BigMouth intake (Snorkel inlet is about as wide as the radiator!), going through a Territory Plenum into the stock manifold.
Speaking of the stock manifold, I also just picked up an FG N/A Intake manifold today for $100 (with the FG fuel rail, injectors (not that I am going to use them) and manifold bolts) and I suggest that as your next mod to do, its a little fiddle-farty, you need to get a bolt spacer kit for the BA injectors (I think these are the appropriate ones: chiptorque.com.au/product/fuel-rail-spacer-kit/ Though I still need to ask if they work with the N/A FG manifold or only the Turbo manifold, they look right at first glance), you need to either make an adapter plate for the BA throttle body to mount to the FG manifold, or just mod the TB itself, and you need the heater piping from an FG barra 195 as well, and need to mod it with some hose to plumb up to the firewall of the BA engine bay (And also in my case, you may need to source an FG oil dipstick), I also suggest pairing it with one of these while you are at it: www.maceengineering.com.au/COLD-AIR-INTAKE-MANIFOLD-INSULATOR-To-suit-EF-BF-6-Cylinder-UPPER
Lastly you will need to fab up some sort of 3" pipework to go from the back of your Mace CAI to the TB, should be a short run since the FG manifold faces the back of the air intake box...I've seen blokes claim up to 20rwkw from doing this mod (after a custom tune ofcoarse) and this sounds reasonable to me, since the first barra engines were 182kw at the crank, and the FG's were 195kw at the crank, a good tune on 98RON combined with all the other supporting mods would see in or around 200kw at the rears (That's the figure I am hoping for).
@Glyn Atkin Hey mate, thanks for watching and sharing. Correct that this is running PH4490's.
As far as the FG intake they do look promising and for an 'all out' NA build it would make sense to test this out but there are more plans for this car in the future where this would have to come off anyway. I'm very keen however to hear how you go and see results once you've completed this, sounds like it's going to be a tough NA combo that would surprise a lot of people.
Regarding adapting the BA throttle body to the FG manifold, are you aware there's an adapter available to suit. Perhaps you are as you seem well across it but if not check it out - facebook.com/customalloywelding/photos/a.1101063416702619/1778062345669386/?type=3&theater
Best of luck mate 👍
@@BrowneysGarage I am aware of his work, I think he was asking $200 for the adaptor plate, which I'll probably end up just forking out for, out of convenience.
Maybe 4.11 diff gears and an LSD should be your next mod then, since 4.11 diff gears are good for the strip, I'm personally thinking of going with 3.9's and an LSD as well as some of my other planned mods.
Just found this series. A: I wish I hadn't sold my Barra, and B: Can you buy a VZ and do a similar series lol?
I already bought the underdrive kit for the VZ, seeing this made me feel like it was justified. I'm doing the timing chains, new oil pump and balancer all at once. Greast vid!
🤣 Thanks very much mate. Maybe you can take your VZ and film a similar series, wouldn't take much to improve on the quality of videos I put out mate it's all pretty basic... including the host.
Hope you get decent results from the underdrives as I felt I did, seems like much more of a no brainer for yourself to do while you're in there at least 👍
Thanks so much for this vid Browney! I've been wanting this kit from MACE for ages, but I was worried about its impact on the accessories. I couldn't find any other user feedback on that issue, but you've given me the confidence to give this kit a go! Thanks mate, love your work!
Hope you enjoy it as much as I did. Not huge power gains or anything but car definitely felt better to drive.
Your a bloody legend mate ! Love this series so far
@Final-Flight Garage Thanks mate, glad people are enjoying following along 👍
@@BrowneysGarage it's been great fun, as you do the mods I buy them and follow along last week I did aftermarket trans cooler & just ordered this pack and once it aarives I'll get stuck in .
Should do a XR6 FG NA series after the B series and see just what difference the rear sump is
@beau ingram Thanks mate, we'll gladly accept any donated cars to test on! 🤣
Love the vids mate
Part 5 needs to be a tune!
@Jed Conter Thanks mate, I’m keen to see what we can do with a tune too but have a few other things coming up first 👍
did you ever test AC out as i wish to fit this kit to a 2015 TERRITORY as i have replace the balancer 2 times now they keep coming off ( crap rubber in the balancer ) going to try this kit the cars only done 120K all i was worried about was city driving charging and cooling and the AC
great video,,thnx mate
Glad you enjoyed it, thanks mate 👍
Putting a limited slip diff in
@Jacob H That may just be the next video...
Plastic fg mainfold also adds somepower aswell think its 10 15kw
Maybe more
@Tim_ Arnold Thanks mate, have seen this done and it’s definitely very interesting. Definite gains to be had there.
Thanks for watching 👍
Also could manual it aswell
@@Mr-Broccoli if u ran those turbo inlet heaps better then fg ones prove 10 20kw also more power to top end
@Mr. Broccoli I wouldn't write of the FG manifold, seems there could be decent gains there - maybe one day we'll give it a go (www.fordforums.com.au/showthread.php?t=11373221). And if you're talking aftermarket plenum I would hope they're better at up to $1k plus compared to a second hand FG inlet but you're right, they seem like a little bit of mucking around to make work and fit right.
Great video good stuff
Cheers mate, thanks for supporting the channel 👍
Hi mate, could you please make a small video how we can find engine number location on xr6 ba 2004 , lot of people say underneath the exhaust manifold, I try to look where but I can't find nothing, thanks
STD BA does 7000 rpm with the original pulley on, guess it might help you down the strip?
Can i do these same mods to my ba xt falcon? like the same exhaust and that
Absolutely, XT and XR6 are mechanical pretty much the same except often different diff gearing.
May also need a slightly different rear exhaust section because the XT doesn’t have the rear bumper cut out but should be stocked by exhaust shops still.
Good luck and enjoy mate
Any more videos coming mate?
New video out this Thursday and plenty more coming 👍
I know car off the road atm getting boosted but since this kit no issues ?
Hey Brock, no dramas at all with this kit so far. It doesn't get driven nearly enough but other than the improved throttle response/small performance gain I wouldn't know it was in there without looking for it 👍
@@BrowneysGarage awsome thx mate
“Maintenance”...... lol I do the same
Haha honestly I think it’s almost more to justify the cost to myself most the time, I’m pretty cheap!
Hey bro, my bf falcon has recently started to flash adp pef we're the shifter symbols are eg P R D. I've replaced the transmission filter and oil and when it's been driving it does stop but still when I start the car it flashes, if u know anything to fix I'd appreciate any help. Cheers
Okay so same voltage as before Otherwise if you don’t get enough voltage your burn out your coils
How has it been going since then voltage wise
I’ll send my revs have dropped down a lot down to about 550 now
Yeah I learnt my lesson do need the kit I need to buy the belt that specially for this balancer and the idlers
No dramas at all to date, even with the turbo on it now.
You should have washed the engine down and changed the Front timing case seal.
R these suitable for a xr6t
Yep, should fit up exactly the same.
Can you get gilmore belts for barras and sohc?
Not that I'm aware of sorry mate, pretty old school tech.
How much was the underdrive kit from mace please.
@Toothless $310 plus shipping I believe, links are in the video description 👍
Hey mate what size belt does this set up use?
2:43 👍
@@BrowneysGarage thanks mate
Anyone around Geelong got a 2nd hand one of them tools avaliabe for purchase?
Yaaaaaaaa!!! Browney's back! That must mean his postie visited him too!
A performance mod, that may be interesting to some, could be diff ratios and if they are worth it on a car like this.
This was a great video. Simple but still informative. Do you think Turbo Taxi runs one of these? :P
@GlensGraphix Mr Glen you legend, good to hear from you. He sure did but unfortunately I can’t put all the blame on the fine people at AusPost! Quantity has slowed a bit here due to other factors and I really want these to be of a decent quality, as much as I can anyway. If that means less videos sometimes I hope people will understand and stick with us, and it seems they will thankfully.
Awesome idea and it’s something I’d love to cover but don’t think it’s going to happen in this one just yet, the diff will be touched next though - are you reading my mind!?
And poor Turbo Taxi and Scotty, the guy can’t catch a break at the moment.
Thanks as always Glen 👍
@@BrowneysGarage tell me about it! Local mail here in Melbourne can take up to a week to get to me. Crazy times.
Thanks @@Mr-Broccoli but I was fishing for a giggle. But your info is handy.
@Mr. Broccoli I'm sure poor Turbo Taxi wasn't running one but don't know if they're completely not worth it, increased efficiency is good for any engine. The dyno graph shown in the video is actually from a turbo car with 7-8rwkw gain I believe, so bang for buck $40-50 / rwkw doesn't seem terrible?
It'd make your accessories rotate faster being a smaller diameter
Other way around as the crank pulley is smaller, this always throws me, so much so that I had to panic and go double check!
Think of it this way. The smaller crank pulley has a smaller circumference and therefore for each rotation the belt is driven less distance. Anything driven off this belt (all accessories) is then spun less for each RPM of the engine. Hope that makes sense, and that my logic is correct! 👍
sharper on the go pedal
Belt diagram should be under bonnet on a sticker anyway
If you're lucky, not here though. Probably an owner's manual thing now?
@@BrowneysGarage Haynes manual better option?
I pressed all the buttons on my keyboard and this came up ngl ur kinda hot 030
didnt do anything did it
11:00 - It's not earth shattering but I definitely think it made some difference. At very least it felt like it improved throttle response which made it more enjoyable to drive. Didn't expect that but I would do the mod again, I was happy with it.
Any problems with overheating sonce the water pump is spinning slower
Try to buy Harmoic Balancer removal tool, as in your video 2 x in last 3 months...Thanks speed part's& XR6 TURBO DEVELOPMENT ..🤌👍
WELL DONE BROWNY. NO FLUFF, STILL PROFESSIONAL. HAD A GOOD LAUGH. CHEERS 195BARRA MAN...