Well done, and works very well. I already asked in your previous video about the controller about the part numbers for the connectors, do you happen to know these(both the large power connector as for the 2 fan wiring connectors)? thanks
Did you happen to see my response on your other post? I don’t know the OeM harness part number but I put a link to the aftermarket ones I’ve seen for sale
My other video on Contour Fan install has the part numbers 21493-B210B or 21493-C370B are the two newest revisions. There are a lot of older revs in a black case but I don’t have the part number for them.
I don't have a part number for a good harness. There are cheap ones on Ebay and Amazon, but i feel the wiring is a little on the small side. I don't use these on my car and managed to get my hands on the OEM plugs which have much larger wire sizes. Search "Engine Cooling Fan Control Module Plugs Connectors Wire Harness 3Pcs for Infiniti G37 G35 G25 Q40" and some might pop up.
@@Mustang5L5 Do you have any pinout for this? If I found it right, ( latch on the top, lookin at the module) 3pin: - , PWM, + and 2pin: +, -. And PWM signal it's not like regular PWM to GND but 12V?
I added a link to the video description. Click on it and go to the first post. Near the bottom is a diagram of the controller wiring layout in terms of POS and NEG. It matches your wiring. I've found the PWM signal responds to both PWM+ and PWM-. I don't want to label what it should be because I don't have any official documentation, but I've used it with both.
Thank you so much for posting this
Well done, and works very well. I already asked in your previous video about the controller about the part numbers for the connectors, do you happen to know these(both the large power connector as for the 2 fan wiring connectors)? thanks
Did you happen to see my response on your other post? I don’t know the OeM harness part number but I put a link to the aftermarket ones I’ve seen for sale
@@Mustang5L5 Hi, yes I just saw your reply. Great, thanks!!
Hi, nice video. Is this an ms2 or ms3? I have an ms2 with extra firmware and I don’t seem to have any spare pins for pwm. Any detail is appreciated
This is an MS3x box that I built, which is why it has a few extra pins
@@Mustang5L5 thanks. I know ms3 has more spares. Was hoping it was ms2.
Amazing what is the part number of the Controller?
My other video on Contour Fan install has the part numbers
21493-B210B or 21493-C370B are the two newest revisions. There are a lot of older revs in a black case but I don’t have the part number for them.
Do you have part number of 2 and 3pin plug?
I don't have a part number for a good harness. There are cheap ones on Ebay and Amazon, but i feel the wiring is a little on the small side. I don't use these on my car and managed to get my hands on the OEM plugs which have much larger wire sizes.
Search "Engine Cooling Fan Control Module Plugs Connectors Wire Harness 3Pcs for Infiniti G37 G35 G25 Q40" and some might pop up.
@@Mustang5L5 Do you have any pinout for this? If I found it right, ( latch on the top, lookin at the module) 3pin: - , PWM, + and 2pin: +, -.
And PWM signal it's not like regular PWM to GND but 12V?
I added a link to the video description. Click on it and go to the first post. Near the bottom is a diagram of the controller wiring layout in terms of POS and NEG. It matches your wiring.
I've found the PWM signal responds to both PWM+ and PWM-. I don't want to label what it should be because I don't have any official documentation, but I've used it with both.