2018-2023 Mustang GT Barton Industries Short Throw Shifter Hybrid 3 w/Reverse Lockout Installation

Поділитися
Вставка
  • Опубліковано 23 гру 2024

КОМЕНТАРІ •

  • @markjones7417
    @markjones7417 Рік тому +2

    Do I have to have those loud guitar riffs playing as I remove each part? I'll need a second person to turn them off and on at the right time.

  • @dinobravo23
    @dinobravo23 7 років тому +22

    Damn. Used to be so easy to install a short throw shifter. Now, its a PITA.

    • @Zerogivengarage
      @Zerogivengarage 7 років тому +1

      Yea it's a lot of work but worth it IMHO.

  • @ZackMuffinMan
    @ZackMuffinMan 24 дні тому +1

    How do you remove the lockout collar one it is snapped into place? I think mine is rattling against the spring and I want to try and fix it with some heat shrink.

  • @vdub5818
    @vdub5818 7 років тому +16

    Man, 2 10mm's are needed for this install? I've searched the earth twice and still can't find 1, let alone 2! 😂

  • @Book20244
    @Book20244 6 років тому +4

    What’s the stimated cost on the install?

  • @texboydstun4736
    @texboydstun4736 2 роки тому

    Greatest improvement to my 2019 GT I had Shelby LasVegassdo the install a bit to much of a job for me 75 year old Gear Head I cannot get over how the shifting improvement is! Highly Recommended

  • @marcasswellbmd6922
    @marcasswellbmd6922 2 місяці тому

    Will that work on my 17 GT?? I want the stock lockout and look????? I'm going to do a body mount.. I hate NVH... Great video though..

  • @rokncobra
    @rokncobra 5 років тому +1

    Hey bill..had a garage do the install and they used all springs. .i find very stiff and notchy..how hard is it to remove springs..can it be done from top inside cabin

    • @cjponyparts
      @cjponyparts  5 років тому +1

      You would need to remove the boot and trim plate and then unbolt the shifter from the base. It is tight but there is enough room.

    • @rokncobra
      @rokncobra 5 років тому +1

      @@cjponyparts thanks..will try it

  • @sgt_loeram1933
    @sgt_loeram1933 Рік тому

    Hey I bought my 2018 GT PP1 with 20k miles on it in Sep 2022. My shifter is different, I have to PUSH down on the shifter to engage reverse. Not sure why or what it has installed. Any ideas??

  • @scatpack1381
    @scatpack1381 2 роки тому

    Is there a review before and after comparing the shifters?

  • @darenerivera6070
    @darenerivera6070 2 роки тому

    At 10:20 I installed the nuts on the driver hand side will there be a problem?

  • @dry509
    @dry509 7 років тому +2

    Question..please advise why you get the manual instead of the auto..trying to decide? The auto is faster and stronger.

    • @triggerxx9760
      @triggerxx9760 7 років тому +1

      dry509 get the auto. You wont regret it

    • @6ixspeedstang186
      @6ixspeedstang186 7 років тому +7

      dry509 get a manual. It's a muscle car, not an exotic or some family car.

    • @6ixspeedstang186
      @6ixspeedstang186 7 років тому +3

      Trigger _ he actually will regret it because it's the wrong transmission to have in a muscle car. Manual all the way.

    • @triggerxx9760
      @triggerxx9760 7 років тому +2

      Brandon Curry unless you want a slower car. Manual is fun but not fast enough

    • @6ixspeedstang186
      @6ixspeedstang186 7 років тому +1

      Trigger _ don't know how you drive but the manual I drive has never kept me from winning races or made me slower.

  • @visions558
    @visions558 7 років тому +6

    He called the slip joint pliers a cresent wrench?

    • @mikereyes6289
      @mikereyes6289 7 років тому

      Visions lol right I was like Wtf

    • @evilone6785
      @evilone6785 7 років тому

      Glad your perfect

    • @visions558
      @visions558 7 років тому

      Not perfect just stating the facts. Usually he is right on the money

    • @Zerogivengarage
      @Zerogivengarage 7 років тому +9

      Because this was the first install I did completely on my own since my hand surgery and by the time we got to the tool list I was in so much pain I simply read the manufacturer by mistake lol . it happens

    • @dennisgross1080
      @dennisgross1080 5 років тому

      Crescent Tool Company

  • @brandonnoll5110
    @brandonnoll5110 6 років тому +1

    Curious if the stifflers driveshaft loop will work with the trans mounted Barton hybrid 3?

  • @bl4d3runn3rX
    @bl4d3runn3rX 7 років тому +1

    Hey Bill, are you guys offering installation as well? I can't find a trustworthy shop in Illinois. Wanna get the Barton, kooks chatted headers a Cai and a tune this year.

    • @cjponyparts
      @cjponyparts  7 років тому

      Sorry no we no longer offer installation, we use the shop for a video studio now. - Bill

    • @bl4d3runn3rX
      @bl4d3runn3rX 7 років тому

      CJ Pony Parts thanks for the answer Bill, any recommendations for a decent shop in the mid west?

  • @digiclear3338
    @digiclear3338 7 років тому +2

    New subscriber, love your videos! Sorry to ask another question about the seats. Thank you for answering the other one. Is there an adjustable lumbar on your recaro seats?

    • @Zerogivengarage
      @Zerogivengarage 7 років тому +1

      No there is no lumbar adjustment. You have up and down and the back is adjustable and that's it.

    • @digiclear3338
      @digiclear3338 7 років тому

      Bill Tumas Thank you so much

  • @alreadytracer8864
    @alreadytracer8864 6 років тому +1

    Hey Bill 😊
    If you choose to use the supplied trans mount, does that effectivley do the job or a blowfish bracket?

    • @cjponyparts
      @cjponyparts  6 років тому

      Yes it works the same way. The Blowfish converts the stock body mount to a floor mount, the Barton Hybrid gives you both options.

    • @alreadytracer8864
      @alreadytracer8864 6 років тому

      @@cjponyparts Thanks Very Much!
      What effect does removing the shelby damper have on the operation of the transmission?
      I saw you guys remove it but didn't see you install it again.
      Cheers! 🙂

    • @cjponyparts
      @cjponyparts  6 років тому

      Hud Bill it had to be removed to install the shifter. We have not had any ill effects from removing it

    • @alreadytracer8864
      @alreadytracer8864 6 років тому

      Okay!
      Thanks Guys, what is the intended purpose of the piece?
      I can't seem to find that online anywhere?

  • @ToG_7
    @ToG_7 6 років тому

    Bill, how do you recommend getting the reverse collar out of the Barton? My 2015 came with a black o ring and the white one and when I installed the Barton I put the black o ring on and then the white one and I believe that is causing some issues with the reverse lockout collar.

  • @alreadytracer8864
    @alreadytracer8864 6 років тому

    Hi CJs.
    What impact does removing the Shelby transmisson damper have? What is the function of it in the first place?
    I can't find any info anywhere else online
    Thanks in advance!.

    • @cjponyparts
      @cjponyparts  6 років тому +1

      I believe it is designed to be more of vibration damper with the stock shifter but I am not 100% sure, I have seen no issues from removing it.

  • @kaveh6390
    @kaveh6390 7 років тому

    Can you guys start doing aftermarket exhaust work/options??

    • @Zerogivengarage
      @Zerogivengarage 7 років тому +1

      We did an X pipe so far, as soon as more options are available we will.

  • @digiclear3338
    @digiclear3338 7 років тому +1

    Are these recaro seats the same exact shape and fit as the recaro seats in the GT 350?

    • @Zerogivengarage
      @Zerogivengarage 7 років тому +2

      Same as the 15-17 cars, the Shelby ones are different.

  • @evandixon1002
    @evandixon1002 2 роки тому

    What bolts were used for top of trans mount arms ?

  • @BMan100
    @BMan100 7 років тому +3

    NOW!..do you guys sell something to reduce the clutch throw length?

    • @3star2nr
      @3star2nr 5 років тому

      Yes. There is an adjustable throw out bearing. But if u don't know what you're doing it's a great way to cook a clutch

    • @kodacres7820
      @kodacres7820 10 місяців тому

      I know your post is 6 years old, but check out the clutch pedal riser they sell.

    • @BMan100
      @BMan100 10 місяців тому

      @@kodacres7820 well I did solve the problem…just cost me more ….bought a factory ordered 21 scat pack challenger with a 6 spd and the hellcat brakes lol. Before the interest rates went up

  • @andrewmorgan5090
    @andrewmorgan5090 Рік тому

    i am having issues going into 2nd gear after installing this, anyone have the same issue?

    • @SaVarMatner
      @SaVarMatner 10 місяців тому

      I am too. I have the flat stick push down version. I'm going to be making sure the shop did it correctly. Mines is Trans-Mounted and the assholes forgot to put my upper boot back in there. But 1st to second at around 5K or more is a no go for me.

    • @andrewmorgan5090
      @andrewmorgan5090 10 місяців тому

      @@SaVarMatner trans mounted here too, ive checked it over three times and tried adjusting top plate multiple times and still no luck

    • @SaVarMatner
      @SaVarMatner 10 місяців тому

      @@andrewmorgan5090 I figured out my problem today. You might want to make sure if you had someone install it they didn't do what my installer did and that is trans-body mount it ☠️☠️☠️
      I uploaded the video on my channel today. I couldn't believe it. So my vehicle is going back to the shop to have everything adjusted correctly.

  • @DanielLopez-ei3nh
    @DanielLopez-ei3nh 4 роки тому

    Am i screwed if i dont have the small white o-ring?

    • @cjponyparts
      @cjponyparts  4 роки тому

      I have never tried without it. You can get an o ring at any decent parts store

  • @josephcienega4773
    @josephcienega4773 7 років тому +1

    Would most 15-17 mustang exterior parts fit an 18 mustang?

  • @alejandrorivera5938
    @alejandrorivera5938 6 років тому

    Thanks for a good video on this install Bill. I was hesitant to get a Barton short throw shifter but I’m gonna send it now lol. Just wanted to know if the instructions that come with the shifter mention the torque specs for all the bolts or do you happen to know what they are? Thanks in advance.

    • @cjponyparts
      @cjponyparts  6 років тому

      Thanks for watching! If there are required torque specs the instructions will include them.

  • @momoo5843
    @momoo5843 7 років тому +1

    Hey Bill i m glad you guys are back with install videos. Even though i dont have a mustang i still enjoy watching your videos. In the video you credit steeda shifters for keeping your transmission from falling. Why is that? That's an intriguing statement hahaha

    • @momoo5843
      @momoo5843 7 років тому

      I meant barton not steeda lol

    • @Zerogivengarage
      @Zerogivengarage 7 років тому

      In my opinion a lot of the failures of the MT82 come from people shifting too aggressively with the stock shifter. There are plenty of other options out there, I have just always run Barton and have been happy with them. My 11, 13, and 15 all had Barton shifters.

    • @jimsauer2453
      @jimsauer2453 5 років тому

      I agree with what you said about people shifting too aggressive with the factory shifter. I position myself so I don’t overthrow on the 2-3 shift also, I don’t slam on it, and I haven’t broken anything. The OEM shifter is a POS! Just picked up a Barton for my 2018.

  • @wzbhnn
    @wzbhnn 6 років тому

    Can this be mounted on the 10-14 cars?

  • @kevinsdb1
    @kevinsdb1 7 років тому +2

    Hey Bill is the Steeda clutch spring still needed for the 2018 Mustang or is the clutch feel not nearly as numb as the 15-17 Mustangs?

    • @dougfa3515
      @dougfa3515 7 років тому

      Good question... I am curious about that as well.

    • @Zerogivengarage
      @Zerogivengarage 7 років тому +1

      I will be adding one shortly and will let you know. The clutch is very light compared to the 15-17

    • @Zerogivengarage
      @Zerogivengarage 7 років тому +3

      The clutch spring is a MUST on the 18, feels so much better.

    • @kevinsdb1
      @kevinsdb1 7 років тому +1

      Alright good to know. Hey Bill are you going to put a Roush supercharger on your 2018 or you going to keep NA and make it a screamer?

    • @dougfa3515
      @dougfa3515 7 років тому

      Cool! Good to know. It will be one of the first things I do once I get one of my own.

  • @evangreer9568
    @evangreer9568 6 років тому

    Thanks for the video, just installed mine on a ‘17 GT. My rubber boot was different than the one in the video but I was able to modify it to make it work.

  • @clarencebenavidez1321
    @clarencebenavidez1321 6 років тому

    My brother has a 15 gt and after he had installed it is smooth in all gears but you gotta force the shit outta it to get in reverse

    • @cjponyparts
      @cjponyparts  6 років тому +1

      I would tell him to make sure the lockout is in the correct location, my car goes into reverse like butter and my 15 was the same way.

    • @clarencebenavidez1321
      @clarencebenavidez1321 6 років тому

      CJ Pony Parts I took a look at it and everything looks good but when you put it into reverse the lip on the lockout just slips off.

  • @scurfie2343
    @scurfie2343 7 років тому

    Did you replace the DS while you were switching the shifter?

  • @qwik281
    @qwik281 7 років тому

    Bill when you gonna try out the mgw?

    • @tazaxx21
      @tazaxx21 7 років тому

      I don't think they do videos on parts they don't sell. Look up SVT Performance for video on the MGW...

    • @tazaxx21
      @tazaxx21 7 років тому

      ...Or the MGW website itself....

    • @Zerogivengarage
      @Zerogivengarage 7 років тому

      I had an MGW on my terminator swapped 96 and it was a great shifter but Tazaxx21 is correct. The Barton shifters have always gotten the job done for me so there is no real reason to try something else.

  • @MustangsbyMatt
    @MustangsbyMatt 7 років тому

    Are there any benefits to going body mount? Would that not have the same level of reliability as trans mount?

    • @Zerogivengarage
      @Zerogivengarage 7 років тому

      The body mount will have a little more play in the linkage but will have less NVH. I barely noticed any going trans mount though so I stayed with that.

    • @tazaxx21
      @tazaxx21 7 років тому

      For the difference between body and trans mount check out Bartonshifters.com

    • @tazaxx21
      @tazaxx21 7 років тому

      According to the guy on the Barton video, when the body mount is used the linkage allows the trans to torque relative to the shifter, but the fore and aft movement is still nice and solid compared to the factory unit. The main difference is the vibration experienced through the shifter. Barton is the only shifter I've seen that replaces the entire OEM lower unit, and still allows a body mount option.

  • @Rob...
    @Rob... 7 років тому

    so want to do this but sooo much work..my wrx was like a 5 minute install :(

    • @Zerogivengarage
      @Zerogivengarage 7 років тому

      Yea I can bang out the Focus short shift in about the same time. This is more work but so worth it.

  • @mistamaog
    @mistamaog 5 років тому +6

    Just when I thought it could be done at home 😢

    • @cjponyparts
      @cjponyparts  5 років тому

      It can be but you will need jack stands and patience.

    • @mistamaog
      @mistamaog 5 років тому +2

      @@cjponyparts Yeah but I'd be paranoid to move any of the other components, like when the transmission was lowered slightly.

  • @r000tbeer
    @r000tbeer 7 років тому +1

    LoL was wondering when you were going to ditch the stock shifter.

  • @Stonefactor
    @Stonefactor 6 років тому

    Will this fix the clutch fork failure issues people are having. They issue basically starts with 3rd and forth gear grinding and then they eventually go out. Will this prevent that?

    • @cjponyparts
      @cjponyparts  6 років тому

      A good quality shifter will help prevent damage to the internals, the Fork issue seems to be a production issue. I have had this shifter on my 18 for over 11,000 miles and no issues.

  • @ArchimedeanEye
    @ArchimedeanEye 7 років тому

    You look like Eric from the channel 'Nomadic Fanatic' bro

  • @Ford_Raptor_R_720hp_V8
    @Ford_Raptor_R_720hp_V8 7 років тому

    Good Choice for a Shifter

  • @mattperry4868
    @mattperry4868 7 років тому +13

    Sorry but the music killed the video, couldn't get past 4 minutes

  • @dry509
    @dry509 7 років тому +1

    Or get a Camaro with a TR6060 manual?

  • @gsheverything_2716
    @gsheverything_2716 5 років тому

    Nice watch man

  • @03bloodredsnake
    @03bloodredsnake 5 років тому

    What a pita this looks like

  • @Zle_blacklightning
    @Zle_blacklightning 7 років тому +1

    Would have been nice to actually see the car move

  • @boostedcoyote8368
    @boostedcoyote8368 7 років тому

    Dope

  • @stuclen1050
    @stuclen1050 3 роки тому

    The music is annoying asf.

  • @agaad22
    @agaad22 7 років тому

    Bro...slow down when you're talking.

  • @jordycruz6661
    @jordycruz6661 3 роки тому

    So will this mod alone fix the issues of the mt82 such as the 3rd gear lockout?