2005 Honda Accord Knock Sensor - Check Engine Light ON!
Вставка
- Опубліковано 10 вер 2024
- How to replace the knock sensor on the 05 honda accord, we use the Hantek scope and the Launch and look at a couple different ways to see how the knock sensor is operating.
I appreciate your posting, it was helpful. However, I just did my son's 2004 Accord and the knock sensor could easily be reached just over the alternator with a deep well 27mm socket with a swivel joint and eight inch extension under the intake. Removing the plastic shroud was helpful to see the sensor, but I found that there is no need to remove the throttle body or intake manifold. As simple as replacing a spark plug and the sensor engine code was resolved.
Do you need wire harness for the knock sensor?
4 cylinder or 6? 6 probably harder to get to.
You helped me greatly! My son failed emissions due to knock sensor. Followed your video and “knocked” this out. Great video snd HUGE thanks! Keep it going! This is by far one of the nest tutorials I’ve watched and learned from.
And clearly I cannot type correctly on my phone 😳
Thanks for uploading this video! Watched 5 or 6 others that made me think I couldn't do this repair, then I saw yours. Maybe it's cuz I live in STL too, LOL. Based on how much money I saved by doing this repair myself I'm more than happy to buy you a meal and/or beer sometime.
Thank you for the help! This turned out to be an easy repair- nice to know (different from the book) to take off the entire throttle body. Hardest part was finding a 27mm socket for the knock sensor itself. Ended up using a wrench... was a tad cumbersome, but got the job done. Thank you.
Yes some people say they can get it out with removing the manifold but I can remove the manifold in minutes and be down to it without much headache at all so that's how I always do it
Took me 10 minutes to remove and replace my knock sensor . Didn't have to remove anything. Long extension reaches it just fine.
You should make a video next time and post it!
@@HooptiesGarage some one did make one and post it.
@@mcard48able great 👍
2 -3", 1-1" extensions , 27" deep socket take me 4 mins w/o remove intake manifold
How do you disconnect the sensors cable
How much is the cost for knock sensor replacement?
Couldn’t get the two top bolts on the manifold off mines
IS IT 24mm or 27mm socket needed? (you mentioned 24mm @11:15)
7:45 you need to take that bracket off and it's a pain in the ass. In the video you're telling viewers not to take it off which is not right. I spent 20 mins figuring it out. Other than that great video. I couldn't find torque spec for the manifold online. It would be helpful to torque anything with a gasket.
I don't take the bracket off the manifold just from the block.
Hoopties Garage you won't be able to pull off the manifold. Yours was already off because someone else took it off before you.
I might be thinking of the element in those you can pull it off without taking that bracket off the manifold. I think you are right on this car someone had already been in there, I think it had a newer starter on it.
Just changed mine how do I clear code ? Will engine light stay on or do I gotta drive ?
Yeah you would need a scan tool to clear it, otherwise just drive it and it should go off within a week or so depending on how much you drive it
@@HooptiesGarage okay thanks I don't have a scan tool I'll just drive it and hopefully it goes off
@@tommylee2411. Go auto zone they have a scanner to loan for free
i Changed mass airflow sensor and knock sensor but the engine light showed up again help please
What is the code ?
@@HooptiesGarage the code as said by my mechanic was to replace sensors and did it. he did the reset but it came back up again. I disconnected the battery, tighten the fuel cap and it came back again. the mechanic says if the car is running good don't worry about it. But it is getting on my nerves.
@@HooptiesGarage p0325 I changed mine out and code came back on what can it be ? Thanks
@@VivaLaRaza619. hello, i have the same problem, did you figure it out?
@@lexu3167 wasup bro , yeah mine all it was was a loose cord tht wasn’t connected when I changed out the starter the guy forgot to connect it back when he put everything back together, I kept thinking it was the knock sensor but nope was just a connecting tht was not connected
I appreciate your video, I just finished, but I got another issue that is a sound and it seems to be losing air somewhere.
Is there anyone who had this issue after changing the knock sensor?
Sounds like maybe one of you vacumn lines either didn't go back on or fell off I would look real close around your manifold and make sure all the hoses are back on
@@HooptiesGarage would that cause the code to pop back on ? One of the vacuum hoses
where does the other end of the wiring attach to?
Goes to the ecm
I had a mechanic switch this out on my mother's car and he said drive it for 100 miles and the check engine light will go off then after it reprograms the computer. Is that correct because I see in this video that you didn't need to drive it to stop the check engine light from coming on?
I cleared the codes after I installed it if he didn't clear the codes then yes it will probably take some drive cycles for it to clear but he should have just cleared the code and took it for a drive to check his work
What a waste of time. Takes like 90 seconds with the proper tools.
How did you unplug it and replug it in without disassembly of the intake?
😂
To much Blah blah blah
Tough crowd.