Dude, thank you a million times! I replaced all of my front end suspension and ended up with a popping noise that 4 shops couldn’t find. Kept getting told everything was fine. I thought the tightening specs on the links were low. I’ve always smashed those bushings to about about the size of the washer on top of them but this I didn’t. After your video I jacked it up, noticed a bit of play, smashed em down and bam! Noise gone. It was driving me crazy. Thank you so much!
This may be the information I needed. Clunking noises? Yes! Just bought four new struts and am about to install them, yet always had that funny feeling that "struts" should never make that kind of a noise when they age. Wrong? Maybe. But the sway bar clip here led me onto a new path of discovery. Thanks ; - )
Im dealing with this now. I just replaced struts, lower control arm, ball joint and outter tie rods and im getting a clunking noise after about 2 months
My mechanic and Hyundai told me clunking sound from car when accelerating is transfer case, quoted me $4k to replace. I inspected myself and found stabiliser link and wheel bearing as noisy, replaced both and clunking noise is gone. Cost me $200 in parts
This channel helped me and my boyfriend my boyfriend was able to save me a lot of money by learning how to change my rotor and calipers on my car from this channel now there’s something new I can add to the list of things I’ve learned incase I run into this problem thanks 1A-auto😊
Great video. Some of the trackday crowd advises to wrap the swaybar with teflon tape to avoid metal-on-rubber contact when the silicone grease eventually wears off or dries out. The teflon tape is mostly to avoid annoying squeaky sounds, but I think this could help the swaybar rotate smoothly and keep the car behaving predictably.
If only the bushings where this easy to replace on all vehicles. Had to do it on and early 2000s cavalier and it was the worst. The car was not worth all the problems it had. The wisconsin weather really did a number on the car. But it was my ex's grandmas car so i tried my best to keep it safe and working for her.
I really appreciate this video I have a 99 Ford F-250 on a 4 inch lift so I probably need to check all of that out what you just explained especially before I take her in the mud LOL
super vid, nice job , excellent lighting and superb camera work . content and mechanical knowledge were on point and relevant. thanks ,,also liked the blooper outtakes at the end ...adds some reality and authenticity to the vid.
Haha. Nice. My 2014 scion tc front left makes a knockong sound. Over rough roads driving straight it rattles. But turning the wheel on curves while driving it doesnt rattle as much. Mainly on the driver side. Looks like i have an idea of where to look now. Sweet.
My Scion TC is making this sound even after changing struts/balljoint + lower control arm. Sway bar link looked good nothing torn but I did not check the sway bar bushing. Intro of this video convinced me it's the same clunk ass noise it's making under on both side driver and passenger on speed bumps.
+Henry Kim We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
look at this new guy he's got all the finesse of an emerging holly wood actor written all over him reminds me of Mark walburn in Basketball Diaries...but hes also kinna givin me that Billy Mays vibe
My 2015 Subaru Forester XT rattles and shakes past 55/ 60 mph. If I slightly turn the steering wheel while driving or making a turn at a similar speed or faster it stops the shaking. Now that the check engine light randomly comes on the rattling/ shaking has stopped. When the check engine light is off the shakiness comes back at 55 mph or faster... Guess ill check sway bar end link's and bushings.
+Dan D We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
My swaybar does minimal movement nothing close to this only wehn i apply significant force with a pry bar. There is no metal noise. Is this normal? I am trying to diagnose a suspension issue and not sure what part is causing it.
Thanks much for your video. I didn't know this. I bought new bushings for my 2000 Camry LE back sway bar. So the bushings are on bear metal. A mechanic put the new bushings on I didn't watch him. Oh geez. I've been wanting to put heavier sway bars on the Camry. I'm customizing the Camry. So where do I buy silicone paste?
I have a 2007 Chevy Silverado 2500hd classic crew cab 6.0 liter gas engine 4wd. Same noise. I rebuilt the entire front end...still happening. No play in the sway bar at all. Any ideas? I've been told replacing the body mounts are the issue, but others have said no it's not. Help!
i have a xtpe jag, 2005. i have changed these bushes and tirods, springs, shocks, bushes where the shocks connect to upper part of the body and one of the arms. I still get a knocking sound on N/S rear wheel. my mechanic has run out of ideas and i run out of cash!. any idea what might be causing it? thanks.
+@tekinmoustafa8141 We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
"CLUNKING NOISES" started from my Marriage shortly after starting,....."SwayBar" needs ADJUSTING😊 (Its NOT a 'Singles Bar' Darling, its a SOCIAL GATHERING, She said😂,....she sure does like "SOCIAL GATHERINGS" I thought...... THAT is the EXACT MOMENT my SWAYBAR BUSHINGS needed some Jacking UP) Just SMILE, and hit "LIKE" You KNOW you 'RELATE'😂❤😂
Good video but I would never purchase anything off you guys again apparently your guys ball joints are made in China and we’re non grease-able I installed your guys kit on my 89 GMC Sierra shortbed which is basically a project truck so it’ll hardly get driven It was installed 2019 and my ball joint popped out the a-arm while driving 25 mph hitting a corner I was stranded for a hour and could of died if I got as on a freeway this was 2022 again this truck was a project truck hardly ever drove ball joints should last 75k-150k miles and I am mechanically incline so it’s crazy I paid $130 for that whole kit which came with pit arm idler arm inner and outer tie rods upper and lower ball joints 🚩 I ended up paying $320 for just upper and lower ball joints (moog problem solvers) pay once cry once my buddy always said well now I know 😢
√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Visit-1AAuto
√ Do it Yourself
√ Save Money
Just turn the radio up loud to drown out the noise.
Dude, thank you a million times! I replaced all of my front end suspension and ended up with a popping noise that 4 shops couldn’t find. Kept getting told everything was fine. I thought the tightening specs on the links were low. I’ve always smashed those bushings to about about the size of the washer on top of them but this I didn’t. After your video I jacked it up, noticed a bit of play, smashed em down and bam! Noise gone. It was driving me crazy. Thank you so much!
This may be the information I needed. Clunking noises? Yes! Just bought four new struts and am about to install them, yet always had that funny feeling that "struts" should never make that kind of a noise when they age. Wrong? Maybe. But the sway bar clip here led me onto a new path of discovery. Thanks ; - )
Im dealing with this now. I just replaced struts, lower control arm, ball joint and outter tie rods and im getting a clunking noise after about 2 months
My mechanic and Hyundai told me clunking sound from car when accelerating is transfer case, quoted me $4k to replace. I inspected myself and found stabiliser link and wheel bearing as noisy, replaced both and clunking noise is gone. Cost me $200 in parts
This channel helped me and my boyfriend my boyfriend was able to save me a lot of money by learning how to change my rotor and calipers on my car from this channel now there’s something new I can add to the list of things I’ve learned incase I run into this problem thanks 1A-auto😊
Great video. Some of the trackday crowd advises to wrap the swaybar with teflon tape to avoid metal-on-rubber contact when the silicone grease eventually wears off or dries out. The teflon tape is mostly to avoid annoying squeaky sounds, but I think this could help the swaybar rotate smoothly and keep the car behaving predictably.
I purchased sway bar link from 1A auto for my camry and the quality of parts is very heavy duty and outstanding 👌
I highly recommend that
I've been chasing a rattle at the front-end. Replaced control arms and mounts. Never thought to check swaybar bushings ! 😮
If only the bushings where this easy to replace on all vehicles. Had to do it on and early 2000s cavalier and it was the worst. The car was not worth all the problems it had. The wisconsin weather really did a number on the car. But it was my ex's grandmas car so i tried my best to keep it safe and working for her.
If it is a 1A Auto video, it is worth watching! Thanks for the valuable content!
Excellent no b.s video, very professional and straight to the point, thankyou from Oz ❤
Thank you for the tips of greasing the bushing, which I wasn't going to do, and facing the split to the rear.
I really appreciate this video I have a 99 Ford F-250 on a 4 inch lift so I probably need to check all of that out what you just explained especially before I take her in the mud LOL
super vid, nice job , excellent lighting and superb camera work . content and mechanical knowledge were on point and relevant. thanks ,,also liked the blooper outtakes at the end ...adds some reality and authenticity to the vid.
I would have sanded the sway bar a little bit and got the surface smooth before putting the bushing on.
Haha. Nice. My 2014 scion tc front left makes a knockong sound. Over rough roads driving straight it rattles. But turning the wheel on curves while driving it doesnt rattle as much. Mainly on the driver side.
Looks like i have an idea of where to look now. Sweet.
Very nice! Local repair network had absolutely NO IDEA what to do for 3 years. Sold the car in the enc.
So how bad is it to not change it immediately?
Thank you A1 Auto for helping me nail down 1 of my gremlins 👍🏽
Thank you for teaching me something new.
Thank you bro now I can do bushings on my Crosstrek
Best video ever
I've replaced everything except those. Hopefully, that will fix the knocking sound. Everything else did need to be replaced.
My Scion TC is making this sound even after changing struts/balljoint + lower control arm. Sway bar link looked good nothing torn but I did not check the sway bar bushing. Intro of this video convinced me it's the same clunk ass noise it's making under on both side driver and passenger on speed bumps.
+Henry Kim We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Best channel on youtube. So informative.
what a great vid. I love the explaining what the parts do for the car!! 1a auto rules!
Great video
That's the sound my Jeep makes! 😅
Immaculate hair!
look at this new guy he's got all the finesse of an emerging holly wood actor written all over him reminds me of Mark walburn in Basketball Diaries...but hes also kinna givin me that Billy Mays vibe
That car looks toast
Does one have to lose the bolts holding the sway bar links? Or one can change them bushings just by removing the brackets?
This is the information I seek in my feed!! This awesome!!
+@michaelgalindo5931 Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Very nice! Show me how to fix rotted parts of a 4th gen 4Runner frame? Please?
Nice video! About to get this replaced
Thank you…well done!
Great video. That truck has a ton of rust underneath. It must be in a northern state, lol.
Excellent video very easy to follow thank you
It's great explanation
Great educational video!
Awesome........ Thank you !
If I do not have a lift do I just put the vehicle up on 2 Jack's and take sway bar off from there w both wheels off?
My 2015 Subaru Forester XT rattles and shakes past 55/ 60 mph. If I slightly turn the steering wheel while driving or making a turn at a similar speed or faster it stops the shaking.
Now that the check engine light randomly comes on the rattling/ shaking has stopped. When the check engine light is off the shakiness comes back at 55 mph or faster...
Guess ill check sway bar end link's and bushings.
+Dan D We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
should I use silicone grease on the sway bar links ?
This was an awesome vid! Great explanation of everything.
Excellent video !!!
Very educative videos...big up
That's the exact sound I've got in my car. No play in anything. I'm gonna check the stupid bar tomorrow
Great video! Well done! Thanks! 🏆
This video was really helpful
Are the ebay and Amazon parts any good, or do we need brand names or oem parts,
Thanks for any answers!
Props to the driver for putting their safety and the safety of everybody else at risk to get that video
No need to dramatize. Road traffic was not endangered by that broken bushing. There are vehicles that don't even have a Sway Bar.
What would cause the truck to feel like it's swaying a little. It was just aligned and a parts were checked.. seemed good.
Show us how to do the rear sway bar bushings on an SUV like the first generation Honda Pilot.
Thanks 🙏🏾🙏🏾 this was really really helpful
holy moses! look at that rust!! thankful im in cali.. jeez
5:31 thank u
Thank you for this video.
Hey man changed out my links and bushings and the sound only stopped for a day and then came back . Wut do u think it could be ?
Very helpful, thank you:)
Great video thank you.
Question do the vehicle need too be off the ground too check this????
I feel terrible for the people that drive in the rust belt or where they salt the roads. 😢
Very helpful thanks!!!
should replace sway bar that old one will chew up the new bushings quick
Thankyou !! ❤
Thanks so much for info
great video👍 helpful👍👍
What's the typical charger on getting that bushing replaced on the sway bar... I have a 2015 and I need that done I believe
What's the name of the lubrication he used?
My swaybar does minimal movement nothing close to this only wehn i apply significant force with a pry bar. There is no metal noise. Is this normal? I am trying to diagnose a suspension issue and not sure what part is causing it.
My car is currently doing this at 35k miles. Is it dangerous to drive even around?
Great !
Thanks much for your video. I didn't know this. I bought new bushings for my 2000 Camry LE back sway bar. So the bushings are on bear metal. A mechanic put the new bushings on I didn't watch him. Oh geez. I've been wanting to put heavier sway bars on the Camry. I'm customizing the Camry. So where do I buy silicone paste?
The clucking could also be bad sway bar bushings and are bad sway bar end links
I have a 2007 Chevy Silverado 2500hd classic crew cab 6.0 liter gas engine 4wd. Same noise. I rebuilt the entire front end...still happening. No play in the sway bar at all. Any ideas? I've been told replacing the body mounts are the issue, but others have said no it's not. Help!
What would cause my 2005 dodge ram 1500 rear end to squaek
how couse sway bar links kit
You failed to mention the cv axle.
Look at those Rusts .
Clunking or Rattlling under your car and suspension seems fine?
*Probably The Neighbours Cat*
Excellent video! My wife likes you... ha ha.
2 bolts missing to the right control arm over your head
just put a full empty pipes ,that fixed every other noises . Services they dont know what they are doing ,just guessing left and right
whats the torque spec
i have a xtpe jag, 2005. i have changed these bushes and tirods, springs, shocks, bushes where the shocks connect to upper part of the body and one of the arms. I still get a knocking sound on N/S rear wheel. my mechanic has run out of ideas and i run out of cash!. any idea what might be causing it? thanks.
+@tekinmoustafa8141 We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
how do you fix rust on a car?
Everything reminds me of her
👍
Thats is the culprit that peeple overlook. I know i did.
Chuckled 2:19
I've seen a lot worse from these 😂😂😂
That noise would never be a ball jlint
"CLUNKING NOISES" started from my Marriage shortly after starting,....."SwayBar" needs ADJUSTING😊
(Its NOT a 'Singles Bar' Darling, its a SOCIAL GATHERING, She said😂,....she sure does like "SOCIAL GATHERINGS" I thought......
THAT is the EXACT MOMENT my SWAYBAR BUSHINGS needed some Jacking UP)
Just SMILE, and hit "LIKE"
You KNOW you 'RELATE'😂❤😂
Good video but I would never purchase anything off you guys again apparently your guys ball joints are made in China and we’re non grease-able I installed your guys kit on my 89 GMC Sierra shortbed which is basically a project truck so it’ll hardly get driven It was installed 2019 and my ball joint popped out the a-arm while driving 25 mph hitting a corner I was stranded for a hour and could of died if I got as on a freeway this was 2022 again this truck was a project truck hardly ever drove ball joints should last 75k-150k miles and I am mechanically incline so it’s crazy I paid $130 for that whole kit which came with pit arm idler arm inner and outer tie rods upper and lower ball joints 🚩 I ended up paying $320 for just upper and lower ball joints (moog problem solvers) pay once cry once my buddy always said well now I know 😢
Mine sound like this but only when I reverse at an angle and drive