Це відео не доступне.
Перепрошуємо.
HOW TO REMOVE AND INSTALL SKATEBOARD BEARINGS
Вставка
- Опубліковано 3 лип 2017
- Does your board sound like crinkling a chip bag as you roll around the park?
Tune into some wise words from our friend levi, as he teaches you how to remove old wheels and bearings, put new bearings in wheels, and reinstall new wheels onto the board. You'll be rolling again smooth in no time!
shop.shredzshop...
"make sure you use a safe counter"
pushes against glass table
HAHAHHAHA SAME
Skate shop glass can stop bullets.
LLMMAAOO AHAHAHAHAHAHA TTTRRUUEE😂😂😂😂😂
@@Mystninja facts
Looks like a very strong glass table :)
it would be nice if u could do some close ups with the camera. can’t see anything you’re doing
Fax
69 likes
Yesterday I broke my ankle because while I was going down a ramp my wheel just came off and it rolled under my foot while I was running from the momentum and now I can't skate for a month.
😂😂🤦🏽♂️ maybe I’m just high but this was funny af to me bro hope you get better tho 💯
This is so unlucky lmao
Ooof
Welp, I hope your skating now
My wheel fell off while I was going up a steep bank doing a 360 revert a few weeks ago. I fell right on my ass and I lost the bearing that came out of the wheel, plus the washers and the nut. Had to rip off all my wheels and put new bearings on all of them. I was lucky to have not gotten hurt at all.
'a couple summers old' is poetic
hahah true
dude just used all your methods in the video to practice when I get my new bearings in. haven't changed the stock Penny bearings and while doing this learned that the nuts were tightened hard. by following your video and giving some wiggle room, they roll much much better then before. Thank you 🙏
Thanks a bunch! Picked up some boarding while things are on lockdown here, and this video helped me replace the worst bearings I've seen in my life lmao.
Literally couldn't perform a full wheel rotation with your hardest spin. New ones are super mint.
I can't take it seriously when you say nut.
There's nut in your skateboard wheel
00:36
@@willow0nlin3 wow
Im switching to fidget spinner bearing they are super cheap and roll so fast
Bmx Rider wtf
@@wadimgirivenko5097 yes they roll perfectly
Guess you gotta buy eight
@@user-mw4cx7qr2q i did
Lol Xd
Thanks man! Just stuck some fresh ones on and they’re rolling great!!
I’m a nubby to this. But your video has my wheels spinning fast. Thanks brother
Glad to hear it!
Dude, you're just amazing. My roller skates were dirty af I don't have that fancy tool to take the bearings off, so I didn't know what to do. You've saved me here bro
Always wondered where the sticker goes...😁
Why am I watching this I’m just getting a new board.
Does Silent Bob also do "how to" videos?
Thank you so much for the tutorial! And for the bonus tips at the end, I have to admit I've been mall grabbing but I'll correct my mistakes lol
Don’t worry about mall grabbing if it’s comfortable for you 🙏
Good video and the quater spin is very usefull❤
My bearings won’t flush (don’t have skate tool currently) and it was hard af to put them in the wheel because they feel rubbery af.. any suggestions??
thanks to you, my wheels no longer suck
14mm socket works well for installing bearings also. Only press the bearing on the outer edge as pressing inside will damage the bearing.
This is the sort of thing I was hoping he’d say in the video: how to press the bearing in without pushing on the inner race. I already damaged one set of reds by pushing them on too hard only using the trucks for instal. THANK YOU!
No wonder walmart boards never roll fast. I say that after I heard about puddles or out in the rain lol. Oh btw I got OJ brand wheels and reds bearings for my custom cruiser board
They're GGGGGGREAT!
I know it sounds dumb but I have 52 mm wheels, I’m scared that if I get a bigger size it won’t fit my skateboard, is that possible?
You should be good from 50-54 or 55mm wheels. Worst case scenario (if you get 55-60mm) you’ll have to throw a 1/8inch riser pad on there and you’re good to go!
I knew a guy who used 56mm wheels. He died.
Not from skating though, so I think you’ll be good.
@MEATBALL *tips hat*
I have 54mm, skate extremely loose trucks, and am just breaking in New bushings so don't have any bushing washers on (which means even looser trucks than I'm used to). I finally started to get a bit of wheel bite so put on 1/8" risers today and actually love the height and how the pop feels. Had the best session I've had in a loooong time. I hope since you posted you've tried some bigger wheels and have continued to skate! 👍
Hold your board however you want. But mongo pushing is no good. Trying to reverse that habit
Yeah the people who make fun of skaters for petty shit like which way your wheel graphic is facing, how you hold your board, etc. Are either 12 years old or they are they definition of a kook regardless of how good they are on the board. All that matters is that you have some park etiquette/respect for other skaters and if your having fun. All else is ridiculous ego stroking. I cared to much about what others thought as a kid and i never allowed myself to put in the dedication to learn the basics because i would be too embarrassed at the skatepark, so i would only like to skate alone or with friends. That is until starting back up later on as a adult and you realize how ridiculous it is to care about stuff like that and to allow it ruin your time at the park. Just skate for yourself and screw what others think. But i do recommend trying to avoid mongo lol
Wait bearings come with spacers?
I installed new wheels but afterwards my trucks are obnoxiously squeaky for some reason. I see some videos of people pouring dish soap in their stuff but I don’t know, I’m scared I messed something up
thank you so much for the tutorial, I was really confused about what I should do with the spacers!
I was once bombing a hill. And my wheel come off. There was back in the mid 90s and I think I was using Cozmo inline skate wheels. As they felt faster. (I was like 14 I didn't know any better) but now they make wheels just like it in the tablet shape.
Just got a new board which came with 8 spare bearings and I’m trying to repair my old one
I got my first skateboard. As a gift for my 9th or 10th birthday by my grandma. Im 17 now and havent changed fixed or tuned up anything once until now
Omg thank you I was putting them on on my own and they were super slow and I was like wtf then I watched this and did it this way and they arent slow anymore thank youu
Stoked it helped!! 👊🏻
Thank you! i have a target board. It’s perfect and a durable board except for the fact the bearings suck
They’re a quick and cheap fix at least!
@CHORRU Cablemaker yea I just got a new board :)
Thank you.
What are the pros and cons all of spacers? For you reccomend? I just got mybsuper swiss 5 bones bearings
was anyone else putting the wheel on the trunks and then hear him say "you want to put the wheel design on the inner side of or else you will be made fun of"..... no, just me lmaoo
😂
I don't understand this. My spacer is moving freely in the middle. Is It supposed to be that way? I didn't use spacers when I was skating -00
Note to self guys don’t put the Allan key metal rim on the grey part of the bearing to push it in. I made the mistake and munted a bearing it won’t spin now great warning
Are bearing spacer really needed please reply brother?
Not mandatory, but they help stoping your bearings from being damaged, so I recommend them.
I don’t have the equipment to clean my bearing and I’m new to skating so idk if I should buy new bearings to buy the equipment to clean my bearings
I have brand new bones wheels and bones swiss bearings both new but the wheel spin isnt long at all?
They usually need to get worked in a bit! They’ll get faster after you ride em a bit
So I have a walmart skateboard and I was wondering does THE BOARD matter or just the wheels and bearings?
Everything matters, but if you're replacing piece by piece, usually the first thing I'd replace on a walmart board is wheels & bearings. Or if you can only afford one, just get wheels. Go get them at your local skateshop and they'll help you out!!
@@ShredzShop ok Tysm!!
i don’t have a washer is that ok?
what wheels you have
Doing it right on the class counter is crazy.
I agree on the mongo part but no one over 40 cares about the "mall grab" and no one anywhere should, ever. Good talk.
Wow it came of so fast thank you so much
Yikes! Strong glass counter top!
how deep should i press my bearings in, should i push it in until it touches the separator thing in the middle, i use spitfire wheels
I usually press them as deep as they'll go. Bronson makes the bearing saver skate tool, and it works really well because you can tighten your wheel bolts as tight as you want and it doesn't dent your shields.
@@ShredzShop I tried to push them but when I push one side the other gets out... the spacer is shaking inside... is that okay?!
Oh no... my board is turning on his own... what shall I do ?!
@@Winter_B12 A bit late of a reply, so i guess that has already been fixed. The board turning on its own is caused by the truck bushings being too soft or the wheels being unevenly worn out. The bushings are most likely the problem and need to be replaced or refitted.
@@shoruda yes, the problem has already been fixed but thanks for replying anyway, really appreciate it
Actually, the problem turned out to be in the puvit (I'm not sure how it's spelled Lol) cups
They were unevenly worn out
Never thought that that could be an issue
Thanks very much, it helped a lot.
I lost the spacer whatdo I do?
I tightened them too hard and now the bolt wont unscrew, any hel?
Is it worth putting spacers in ??
I think so, stops the bearing runbing against your trucks.
Thanks bruh 🤟🏾
Works like a charm 👍
where do you put the washers tho
Wait each wheel has two bearings? I guess that explains why they come in 8 packs
dudeee thank you so much appreciate it .
Glad we could help!
Do you have to have spacers?
Nope! They help tho!
@@ShredzShop Ok thank you!
Which side is the protective casing😅
Great Vid! Thanks!
Glad we could help 🙏🏻🙏🏻
my bearings don’t have a hollow or empty side how do I figure out what side to go on the inside of the wheel?
You should be able to do either, unless it’s marked to put one side out
Exposed side inside the wheels basically man shielded side outside
Why the hell andelez swiss bearings(blue) don't come with spacers? Can't find them in skateshops here.
Between you and I... andele are some of the worst bearings I’ve ever rode in my life.
@@ShredzShop well damn. Thats not a good thing to hear after trying to start skating at 30 years of age. Well, I got some Bronson g3's on the day then, how about them?
@@theturk360 Everyone loves Bronsons especially the G3 and Raws. If you stick to Bones & Bronson for bearings you should be smooth sailing!
Are spacers necessary or is it okay without them?
You don’t need em! Just use them if you’ve got em!
@@ShredzShop 😲🤔!!
It’s the yelling for me
Was this filmed in from across the room in the dark and fully zoomed in?
I got brand new super red bearings and they are super slow in comparison with my old regular reds bearings. What the hell I did wrong my older board was setup by the shop and my new board I setup.
Sometimes you just gotta work them in a bit. Also make sure you put them in straight and the wheel isn't wobbling! 👍
So I don’t put any cream on it
How much bearings in each wheel?
2
nice the camera guy is 2 miles away so we can see everything.
It’s funny that I have the exact same bearings
🤝
It would be great if i could see the details in close up, as i cant, video is too far to see small parts.....
sorry maybe its good... but not for a total beginners as we need to see what goes and where...
my board doesint have a sapcerr
Em I to weak? I can’t take them off 😂
Shredz Shop i got them off. Figured it out.
Awesome 👊🏻
People who put stickers on there boards 💀
Always put your reds sticker on your board.
Bill Danforth of the legendary Alva skate team pushed mongo. Push mongo-represent.
goofy foot and mongo. I'd like to see that.
Do I need washers for bearings I’m a beginner
You need washers
Need more closeups. The obvious is not at all obvious to a newbie.
Appreciate the input!
I skate Mongo and could not care less what anyone thinks. Biggest way to have fun skating is not care about the follower way of people making fun of others because someone else told them to.
👨⚖️
Still can’t take beating out
Lol u got corrected
But... why is there no speed washers in my board?! Like seriously lol
You didn’t explain how to take it off
ye he did
Welp I broke my finger
how lmao
Me: Why tf woud anyone need to rethread anything..
Explination: 2:00
Kind of fkd up how judgmental a lot of skaters are but it’s only the fkin losers. There’s some cult mentality going on with how if you don’t do what everyone does you’re a poser or some sh.. I’m glad you shined a light on the wheels going with the graphic inside the board and not out, to me this is stupid I don’t care either but for someone to make fun of you for using your wheels with the graphic out is super dumb or if you have wheels with any color other than white is stupid too.
Do whatever u want and have fun.
You can tighten the nut all the way if you have a spacer and you are putting way too much into how you want others to see you.
"buttery smooth" after visibly struggling for awhile
this video is weird
This didn’t help at all it made it worse
Some unknown person thank you! Please like and subscribe to make things even worse!!
Shredz Shop 😂
Shredz Shop 💀
L
Li
Bad angles
thank u
Which side is the protective casing😅
One size should be covered (on. most bearings) and one side should have the ball bearings showing, put the covered side facing out to eliminate dirt. Unless it's covered on both sides, then It doesn't matter.