Straight Axle Swapped OBS Chevy UPDATE AND FAQ
Вставка
- Опубліковано 5 вер 2024
- Finally got around to doing an FAQ video and update on my SAS project. Hopefully i answered a few of your questions!
Build video:
• Chevrolet K2500 STRAIG...
Walkaround video:
• SAS Chevy K2500 Walkar...
Absolutely love the truck. From the lift, extended cab, big block, camper, this is the shizniz!!
Thanks!
Beautiful workmanship. It looks like you really chased down a lot of the details that often get left undone by lesser mechanics. 👌
It's a shame these platforms are so difficult to SAS IMHO but then again, GM didn't design them to be a straight axle vehicle 😁
My finding over this issue is two things - 1 frame movement/ flexing , 2 change alignment of pitman arm and if u can get high pinions for tops of hub/spindle .. if u have e let's say 2" lift run u a 4" pitman it will have much better steering response. And also make sure the track bar matches the design of pitchman steering shafts
Hahhhh some of us have snapped that damn fitting off the back engine. This is a sweet build man mucho props to you friend.
Damn good fab work performed🔧🔧🔧 One of awesome yrs for Chevy/GMC trucks.
Thought about going this route on my 1stgen 02 tundra. But decided to just rebuild old system instead due to time.
Really nice truck. I’m thinking about doing this with my 98 Tahoe.
Great info! Thanks for sharing. Truck looks awesome!
Nice build. Looks good.
With manual locking hubs you don't need to drive forward and backward to make sure. That's for auto locking stuff
been having this truck for like 3 years each time it breaks down i think its a total loss and ends up being something simple or easy fixes, spark wires or fuses
Pinion angle is a bit to much and need another inch of drive line I reckon. But awesome build man
Very nice SAS - thanks for sharing! I just finished the same ORD setup on my 1994 2 door Yukon. I used the ORD spring brackets, front and rear, on a Ford Dana 60 Kingpin and 14 bolt, respectively. I used the Yukon OEM springs on the rear and standard Chevy 3 leaf front springs (0” lift). Question, which front ORD 10 leaf lift springs did you use? My front springs are stiff with very little flex - but I used them for the 0” lift. I’m considering the ORD 10 leaf springs in the future.
The front springs are the 47 inch “2 inch lift” ORD springs by Alcan Spring. They ride very nice and flex well! Worth the money
I zip tied my actuator to the frame and it fell off. the transfer case still shifts the only difference the light on the button flashes. it works just fine, HOWEVER...I have a manual transmission that was swapped in, not sure if that makes a difference.
holy shit thats a clean truck!
where did you get the front leaf spring mounts?
Thanks! The leaf spring hangar kit is from Offroad Design
How did you make front drive shaft to work
Double-cardann 1330 at the T case
What spring hanger kit are you using
So, what would you say it's the best pick of transfer case and differential to do this if you were to do it manual 4x4?
“Best” haha well everyone had a different opinion. I like doing the least work possible that’s also the most reliable. Keep it simple. Stock 241 transfer case with the floor shift is plenty fine and a driver side high-pinion front axle. I have a 243 which is the electric shift version that came in the truck. I don’t feel the need to replace it because it works just fine.
If you want to make things harder for yourself you can get a passenger side drop low pinion axle then you have to get a passenger side drop 241 or a 205 and pay more money for an adapter to clock it so you don’t bind your front driveline up.
If money wasn’t an object I’d buy a driver drop NP205 and a Off-road Designs Magnum reduction box… with the adapter plates… that would be sweet with a NV4500 in front.
@@Calikov762 nice thought!
@@Calikov762 thanks for feedback, I also think is better keep it simple.
Appreciate man
Drag link what do I order???
It’s on Offroad Design’s website under the steering section, specifically for the GMT400 with crossover steering
what camper shell do you have
It’s a Leer
@@Calikov762do you know where I can get one or do you have a newer model on your truck?
@@claytonmurray4885 this was on another OBS Chevy. I bought it off a guy on Craigslist for $200
What axle is it from what Ford
1989 F350 Dana 60 Kingpin
Big block ??
Yep 454.. 7.4L vortec
My Son has a truck like this. He has a 3 inch body lift and 6 inch suspension lift. He is running 42 inch super swamper boggers on it. Never have a problem with the CV shafts breaking. His truck goes everywhere. No need to swap axales
@@bradleymadosh911it won’t flex like this. id wager it’s less capable than this build
Guys I will strait axle your trucks for 12 15 k.