1972 XL Ironhead Bobber
Вставка
- Опубліковано 21 сер 2024
- 20140325212404 1
1972 XL Ironhead Bobber #108 Sportster clutch primary motor repair harley by tatro machine
the start of the walker saga and his bobber sportster.
it started as a case repair job and turned into a major complete bike rebuild but still keep the rat bike look walker likes.
tatro
Tees, Hoodies, Hats, Parts at : tatromachine.com
Thank you for posting this, learned a bit for putting my 72 sportster back on the road while doing more myself this time around and not being a mechanic this helps!
Thanks for taking the time to make this, just got a 74. Learning all I can. If these haters know everything why the hell are they watching how to vids?
i guess it is kinda off topic but does anyone know of a good website to watch new tv shows online?
@Zev Arlo I would suggest FlixZone. Just search on google for it :)
@Zev Arlo i watch on Flixzone. You can find it on google =)
Did mine today without a video. I kinda knew what to expect and after watching this video. Yeah that's about what I did. Thanks for the video
Great clutch and primary assembly video👍
Thanks for the videos. There very helpful for someone starting out and I like watching them. And you know your shit...lol
🤘😎🤘
👍
Thanks for the info. I adjusted my 75 sportster the same way and seems a fairly straight forward process. I even tried adjusting as described in the manual but my clutch just wont work. I wound the adjuster screw in until it seated and wound it back 1/4 turn and locked it off. I adjusted the cable with a little slack not tight so the ball bearings are correctly seated. Doesn't matter how many ways I try my clutch just wont disengage like it should when I pull the lever. Any suggestions on what I should be looking for ?
try adjusting it at an 1/8 of a turn. the inner clutch plate that has the studs on it needs to be flat and not over torqued. make sure that you use the stock large diameter spacers that go onto the studs on the plate. those thin ass replacement spacers are junk and don't hold the outher pressure plate flat and square.
tatro
@@TatroMachine Thanks for that I really appreciate your comments and videos. I found that if I wind the adjuster screw in about 1.5-2.0 turns there is a sweet spot that the clutch disengages when I pull the lever. I know that’s not how it should be but could that indicate what the problem is before I start buying spacers and new plates?
Thank you for the vid. As I am letting my clutch out when it starts to engage I feel a small buzzing or grinding at the last second if releasing the clutch. Do you know what that my be?
no, take it apart and see what is wrong. broken cases are very expensive to fix, small parts are not.
tatro
@@TatroMachine thank you I’ll have to pull the primary cover. I was thinking either throw out bearing or compensator.
I'm guessing it's safe and or easier to use a impact when changing out a new primary chain
it works for me.
tatro
Hi , I have a 1976 bicentennial ironhead, the clutch basket is oval for this reason I have to leave the chain sluggish and it makes noise. Can you tell me if I can solve it by buying a used clutch basket? or are they all oval after a few years? Thank you
just go find a good one.
tatro
I know Keenan is busy moving so I'll ask everyone this question.
With this style clutch, If the adjustment screw and nut were removed all the way from the primary cover ( while the cover is attached to the engine) is it possible for the bearings to fall out of the ramp assembly ? It they can fall out, is it a certainty that they would fall out ? Is it possible that maybe they wouldn't fall out if the adjustment screw and nut were completely backed out of the primary cover ?
Im sure its easy to guess why im asking this question. I did manage to get the adjustment screw and nut reinstalled. Clutch releases and engages by squeezing the clutch hand lever. It just dont feel like it seems it should.
maybe but not likely. if you start pulling on the lever than you might have some issues.
tatro
How do you remove the hub nut on a 69xlch without a air wrench? I need to replace the kicker assembly
put it in high gear and block the rear brake some how.
tatro
keep up the good work great source of info...any idea on this my 72 xlch1000 jack it up turn rear wheel can select all gears feels smooth no binding,peddle travel seems a bit far between gears but managable.but start the bike select 1st take off an suddenly peddle travels huge between gears they still select but can not get gear without lifting your whole leg as they about 4inches travel between each one.turn it off an peddle travels back to managable,iv adjusted clutch numerous times (no slip or drag) and the gear linkage distance (fitted with forwards) makes no difference..gear box prob or clutch any1 ??
sounds like the shift shaft inner lever is loose on the shaft. time for a new one before it lets go.
tatro
@@TatroMachine thanks alot,sounds like thats probably it as iv a bit of lateral and horizontal play on the shift shaft at the casing.
Could you post the link where you got the parts for Barnet clutch
What is the gasket sealant used? I couldn’t make out what he called it.
I believe he said Goop?
Check that, I think it's just a shop name, Goop. Search down a bit and he writes... 3 bond 1184. Sorry about that
what is the name of the goop tube you used to hold gasket? You talk fast and low and I couldn't catch the name when you said it.
3 bond 1184
@@TatroMachine THANKS!
i need my 71 iron head worked on ... where are you located?
What is the sealant used on the primary cover?
Looks like Three Bond 1194
Would just like to add ,,that little thing is referred to as ," Ball and Ramp," ,,,I think, I could be wrong.....
i call it a clutch release mechanism.
tatro
What spacers should I use and where can I get a set
the stock ones. try tatro machine.
tatro
@TatroMachine I did not see anything on your website , do I need to call to order ? Thanks !!
email works best but calling is good too. tatromachine@cox.net
tatro
I'm in North Carolina what time is best to call ?
Welding on the case without first heating it up in a oven to get rid of the oils and junk the case has isn't the right way to weld on that case. Weld won't last . and cracking a customer's case has to be the worst . and throwing clutch parts on metal and installing parts that have broken studs to go into a clutch . if this was done to my bike I think u would be paying a shop that takes pride in there work instead of this getto type work..
when you are use to welding crap you get very good at it. if these welds were so bad then how come they looked so good after they were cleaned up. if you want the white glove treatment than go to harley and see what they do for you.
tatro
Just put a new clutch plates in mine it doesn't spin like that in neutral.
Could you post the link where you got the parts for Barnet clutch
a place called tatro machine. ever heard of them? what do you think i do here.
tatro
@@TatroMachine thought you was a mechanic didn’t know you were in sales
@@TatroMachineyou aggravate paying customers is what you do best. Of course I'm joking, I just couldnt let this one go