LG Washer Power Button Not Working? Learn How to Fix! [LG Panel Removal & More!]
Вставка
- Опубліковано 15 жов 2024
- In this appliance repair training video we will help you fix your LG top load washer. The model used in this video starts with WT7305. So If your LG washer has no power most of the time it's your MPC and in this video we will show you how to replace LG washer control board. The LG top load washer no power is a common problem. If you need parts numbers for your LG washer repair check below. All the hard work of research is done for you!
✅ PART NUMBERS FOR YOUR WASHER CHECK BELOW👍
WT7305CW
PCB Assembly & Display, Part Number EBR86692724
PCB Assembly Display [ONLY] Part Number EBR85755514
✅ PART NUMBERS FOR YOUR WASHER CHECK BELOW👍
WT7305CV
PCB Assembly & Display, Part Number EBR86498808
PCB Assembly Display [ONLY] Part Number EBR85755508
✅Subscribe to our channel to evolve part of our channel. Thanks for visiting our channel. Hope this Video was useful for you. Please comment, like, share and subscribe to the channel to get more videos like this.
Thank you!
So frustrating - ours is 2 years old and does this. Our last LG was still working after 11 years. The new washer and dryers are junk!
Thanks for the video! I’ll give it a shot.
Check out my video titled 'Unbelievable Fix for Your LG Washer Power Button - What's the Reynolds Wrap Trick?' It could save you a lot of money. You'll find it in my LG playlist.
@@onlineappliancetechman I missed this comment. Between then and now I tried working with LG and they sucked. Terrible service. Tried your foil trick today and it worked!! You are the man - subscriber for life!
Just ordered a front panel replacement from lg and got it installed. Thanks so much! You legit saved us hundreds of dollars!
Very happy we could help! Happy New Years!
Happy to help!
How much it cost
How much did it cost?
Very helpful - Any concerns about the foil causing a spark or fire?
This video was very helpful for the teardown. After taking the entire thing apart I was able to fix it all with a small piece of tinfoil! The way the system works for the buttons is through a capacitive charge that is sensed from your finger by using little spring antennas that are on the main board. The issue seems to all be coming from the actual front panel glass. The glass is either too thick for the signal to pass through or there's a coating that rubs off over time. The fix is as simple as extending the spring antenna, they sell special foil that can be used to stick on the glass to amplify the signal but I just used a small piece of tinfoil under the glass where the power button is that the spring sits against (I put a tiny piece of tape on the edge off the foil to hold it on). The antenna actually sits on the glass slightly offset to the right of the power button image. So I just made sure the piece of tinfoil was large enough for the antenna to sit against it and also be behind the cover panel button image. I would say the piece was probably about the size of a quarter.
Happy we where able to help! And thanks for the info!
@@onlineappliancetech you can also use some aluminum foil tape, but most people don't have it and it's a lot more expensive and not worth getting since you only need such a small amount.
I had the same problem with my just over the 1 year warranty lg top loaded washer, same model displayed in this video. I was able to permanently fix by cutting a square piece of Nashua flexfix dryer vent tape ($6) and sticking it on the outside glass over the power button. Maybe 1.5 in by 1.5 in. This amplified the capacitive charge from my finger enough to return the power button back to normal function.
Thanks for this comment! We just put tin foil and now it’s working!!! Saved us hundreds of dollars!
@@KeepingupwiththeKinyons
My washer is 2 1/2 yrs old, model WT7305CW. Was having the same issues and for a while could unplug and plug back in and it worked... but then that stoped working. Took it apart and found out the problem was the front panel was not connecting to the control board. Put some aluminum foil on front panel, where the start button and pause button connected to the control board and it fixed the problem. Now it works perfectly!!! Cost $0. Hope this helps someone.
Hey, thanks a lot! I put some foil right where you said and that fixed the problem.
I'm having issue with it turning on. If i keep playing with the button it finally turns on. I'm going to try this.
Any concerns about the foil causing a spark or fire?
Thanks to all who suggested the tin foil process. We had replaced the mother board and the start process remained intermittent. Installed Nashua tin tape and the machine is now fully operational. biggest problem was reengaging the master setting dial but figured it out. If your machine is fairly new would definitely suggest the foil play before replacing the board. If you do replace the board I would still install the foil tape to save another reassembly.
I just did this on our LG and it freaking worked!!! Thank you for posting!!!
You're welcome!
Can you link the display board control panel you ordered? I have that exact washer
My panel is no longer responding but if I move the door around sometimes I can get it to run. Is this still a panel issue? Is there a door sensors?
What he did in this video. Is not the problem in most cases. Check the control right behind where you push. Use you phone to magnify the image. You will see if control panel is broken right where round membrane joints the square one. You can also tell you by pushing the button on the control board and and washer should turn on and off if the problem is control panel
Information of the work light, where can I get one
Hey I know I’m late to the party but I did the display board swap right? Ok well without the front cover on I can turn the washer on by touching the spring that is the power on the display board. (This will shock you so if you’re not versed in electrical theory please do not attempt.) however when I put the front cover with the power display button to safely do so, I get nothing. Please help.
Never mind 😂 I found your foil video after. I figured it was something goofy like the circuit wasn’t completing since it worked when I touched the bare spring while being grounded. I’ll try that before bugging again.
Great video, very informative. Thanks
Also, it would be great if you could post the links for where to buy the parts in your videos. My washer’s model #WT7700HVA
@@edgarr6828 I have the same model same issue did you find the part or the part number?
Great video! Worked perfectly! Thanks
I'm so glad to hear that the video was helpful for you! Thank you for watching and leaving such a positive comment!
Where did you find the part? Price??
Thank you so much for this video. Fixed my problem asap.
Do you have a link to buy the display board? I'm having the same issue but cannot find the replacement part
Can you text me model number please and I will try to find for you.
Where can I purchase control board. Thanks
@@onlineappliancetech where can I purchase control board?
@@dorothygranzin7613 Hi Dorothy, I have a newer video that shows you how to fix the no power problem with a piece of aluminum foil.
The aluminum foil fixed my issue with the start button also.
Thank you so much for sharing your experience! It's always helpful to hear feedback from viewers. I'm glad the aluminum foil method worked for you as well.
where can i buy this mother board? Whats the part #?
i have the LG model # is WT7800CV?
Had the touch panel replaced under warranty, then the machine started throwing water supply errors. Tech only replaced the facia and not the component board, had to have them come out again. Should have done the work myself as not entirely sure when went wrong with his work.
Did he turn water back on all the way?
Sorry for the delayed response. Yes, water was turned all the way on. I verified flow through hoses and no issues found.
Oddly enough, I did the LG reset process, unplug, hold power button and then start/pause button. The unit hasn’t thrown the water error issue since but the fabric softener tray will not flush out. Took the tray apart, ensured there was no sticky residue or blockage and still nothing. Seems like the water is not being directed to that portion of the tray during the rinse cycle.
Heard LG was a great product so we thought, why not. Beginning to question our choice.
Where did you get the front panel assembly for $35?
LG.com
i tried this but cant get anything but them wanting to sell me a washing machine?, any suggestions on navigating to get that same part you got?@@onlineappliancetech
Can you provide me with a link for both control boards together. Model #WT7600HKA
EBR81634405 Display PCB Assembly- The Main board is separate for this one it seems? I would call LG for a part number to see if you can buy together.
@@onlineappliancetech Thank you!
@@MrKleeg1st You are very welcome!🙂
What is the part called
Could you seen me the model number and the problem you are having I would be happy to help!
My start button is starting not to work.....
We change the control board but still did not start .
Try the foil. It might be that the front cover has warp or such not and no longer makes contact with the spring. The foil will complete the circuit so your touching the button location will allow the capacitance change to be transmitted to the control board. I tried this today and it worked great.
@@Privat2840 where do you put the foil? I’ve taken the whole thing apart but can’t get the second white panel where buttons are off?
I called LG and I believe I have to buy the control board separate from the display board 😩
You can buy them separately from other sellers...